{"title":"Residential Electric Water Heaters | Montreal, Laval, Longueuil, South Shore and North Shore","description":null,"products":[{"product_id":"chauffe-eau-electrique-bradford-white-re16u6-1nal-6-gallons-montreal-laval-longueuil-rive-sud-rive-nord","title":"BRADFORD WHITE RE16U6-1NAL Electric Water Heater (6 gallons) | Montreal, Laval, Longueuil, South Shore \u0026 North Shore","description":"\u003ch2\u003eHot water with no wait at the farthest tap, thanks to a 6 US gallon tank\u003c\/h2\u003e\n\u003cp\u003eIn a large home or a commercial space, a sink or washbasin is sometimes located far from the main water heater. Every time it is used, the cold water sitting in the piping has to run before the hot water arrives. The \u003cstrong\u003eBradford White RE16U6-1NAL electric water heater\u003c\/strong\u003e solves this at the source: this small \u003cstrong\u003e6 US gallon (5 imperial gallon, 23 L)\u003c\/strong\u003e tank is installed right next to the point of use and supplies hot water almost instantly. It runs on \u003cstrong\u003e120 V\u003c\/strong\u003e with a \u003cstrong\u003e1,500 W\u003c\/strong\u003e element. AirGreen installs it in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and on the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch3\u003eThe point-of-use water heater principle\u003c\/h3\u003e\n\u003cp\u003eA point-of-use water heater does not replace the home's main tank. It serves a single sink or a small group of fixtures in the same spot. Since the hot water only has a few feet of pipe to travel, it reaches the tap without delay, and cold water is no longer wasted while waiting. This type of unit is also useful in a building where a sink is added far from any hot water supply: it avoids running a long hot water line through walls or ceilings.\u003c\/p\u003e\n\u003ch3\u003eWhere it comes in handy\u003c\/h3\u003e\n\u003cp\u003eThe RE16U6-1NAL is the smallest of the residential tanks in this Bradford White line. It suits a kitchen island far from the main tank, an office kitchenette, a basement bar, the washbasin of a powder room added during a renovation, or the utility sink of a commercial space. At 14 in. in diameter and 16 3\/16 in. tall, it can often fit in a cabinet under the sink or in a nearby closet; we measure the space and the access to the connections before confirming the location. It is not meant to supply a shower or a bath: its reserve is designed for handwashing, dishes and cleaning.\u003c\/p\u003e\n\u003ch3\u003eManufacturer data\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003eCapacity:\u003c\/strong\u003e 6 US gallons, 5 imperial gallons, 23 L.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eFactory wiring:\u003c\/strong\u003e 120 V, a single 1,500 W element, unless otherwise specified when ordering.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eRecovery:\u003c\/strong\u003e 7 US gal\/h (6 imp. gal\/h) at a 90 °F rise, or 26 L\/h at a 50 °C rise, based on 1,500 W operation.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eMaximum wattage:\u003c\/strong\u003e 3,000 W, regardless of voltage.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eElement:\u003c\/strong\u003e immersion, screw-in, copper; INCOLOY-type element available on request.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eConnections:\u003c\/strong\u003e all water and electrical connections are 3\/4 in. (19 mm) NPT, with factory-installed dielectric fittings.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eInternal lining:\u003c\/strong\u003e Vitraglas with Microban.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eDimensions:\u003c\/strong\u003e height of 16 3\/16 in. (411 mm), diameter of 14 in. (356 mm).\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 35 lb (16 kg).\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eA single 1,500 W element at 120 V\u003c\/h3\u003e\n\u003cp\u003eThe RE16U6-1NAL is shipped wired for 120 V with a single 1,500 W element. This configuration lets it run on a 120 V circuit, without the two-pole circuit a large tank requires. Bradford White also offers the series in 208 V, 240 V, 277 V and 480 V, single-phase only, but for this model the wattage never exceeds 3,000 W, regardless of voltage. In the vast majority of cases, the factory configuration is the right one. We provide a dedicated circuit and check the capacity of the electrical panel before installation.\u003c\/p\u003e\n\u003ch3\u003eWhat to expect from 6 US gallons\u003c\/h3\u003e\n\u003cp\u003eA small reserve empties quickly if the water is left running for a long time, after which the element reheats it at a rate of 7 US gallons per hour for a 90 °F rise. For handwashing, rinsing dishes or cleaning a counter, this is more than enough, since each use takes only a fraction of the reserve. If the sink is used to fill large pots or to feed an appliance that uses a lot of hot water, we steer you toward a larger size in the same line instead.\u003c\/p\u003e\n\u003ch3\u003eConstruction and compliance\u003c\/h3\u003e\n\u003cp\u003eThe tank is protected by Bradford White's \u003cstrong\u003eVitraglas with Microban\u003c\/strong\u003e lining. The element is immersed and screwed in, so it can be replaced without changing the tank, and the factory-installed dielectric fittings limit corrosion between the tank and the copper piping. According to the manufacturer, all models in the series are UL listed, and applicable models are verified by CSA for energy performance under standard C191.1-M90.\u003c\/p\u003e\n\u003ch3\u003eManufacturer's warranty\u003c\/h3\u003e\n\u003cp\u003eThe RE16U6-1NAL is covered by a 6-year limited warranty on the tank and 6 years on parts. The detailed terms are provided with the quote.\u003c\/p\u003e\n\u003ch2\u003eInstallation of the Bradford White RE16U6-1NAL by AirGreen\u003c\/h2\u003e\n\u003cp\u003eAirGreen is a family-owned heating and cooling company established in Montreal, active for more than fifteen years. Electrical connections are made under our RBQ licence 5645-9605-01, which covers ventilation, refrigeration and electrical work. After a \u003cstrong\u003efree on-site estimate\u003c\/strong\u003e, you receive a \u003cstrong\u003ewritten quote\u003c\/strong\u003e. Installation includes:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003echoosing the location as close as possible to the tap served, with access for maintenance;\u003c\/li\u003e\n\u003cli\u003eremoving the old small tank, where applicable;\u003c\/li\u003e\n\u003cli\u003econnecting the cold and hot water in 3\/4 in. NPT;\u003c\/li\u003e\n\u003cli\u003einstalling the relief valve and its discharge line;\u003c\/li\u003e\n\u003cli\u003ethe 120 V electrical connection on a dedicated circuit;\u003c\/li\u003e\n\u003cli\u003efilling the tank completely before powering it up, then setting the temperature;\u003c\/li\u003e\n\u003cli\u003emaintenance and usage advice.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eMaintenance and safety\u003c\/h3\u003e\n\u003cp\u003eEven a small tank must be filled with water before it is powered up, otherwise the element can burn out within seconds. It is the first thing we check at commissioning. After that, we recommend a partial flush once a year to remove sediment, especially if the water is hard, along with a test of the relief valve. If the tank is installed inside a cabinet, keep the access clear so it can be inspected.\u003c\/p\u003e\n\u003ch3\u003eService area\u003c\/h3\u003e\n\u003cp\u003eWe install this water heater in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e and \u003cstrong\u003eLongueuil\u003c\/strong\u003e, as well as in Outremont, Verdun, Pointe-Claire, Brossard, Saint-Lambert and everywhere on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e. When it is part of a larger renovation project, our \u003ca href=\"\/en\/pages\/financement-avec-financeit\"\u003efinancing\u003c\/a\u003e lets you spread out the cost.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRequest your free estimate for the Bradford White RE16U6-1NAL.\u003c\/strong\u003e A photo of the cabinet under the sink and of the electrical panel is all we need to prepare the visit.\u003c\/p\u003e","brand":"Bradford White","offers":[{"title":"Default Title","offer_id":67799686381860,"sku":"RE16U6-1NAL","price":0.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0715\/1694\/6724\/files\/CHAUFFE_EAU_ELECTRIQUE_BRADFORD_WHITE_RE1_UTILITAIRE_RE16U6_1NAL_6_GAL_US_00_MONTREAL_LAVAL_LONGUEUIL_RIVE_SUD_RIVE_NORD.png?v=1793082266"},{"product_id":"chauffe-eau-electrique-bradford-white-re110u6-1nal-10-gallons-montreal-laval-longueuil-rive-sud-rive-nord","title":"BRADFORD WHITE RE110U6-1NAL Electric Water Heater (10 gallons) | Montreal, Laval, Longueuil, South Shore \u0026 North Shore","description":"\u003ch2\u003eA small 10 US gallon tank for the workshop, the office or the cottage\u003c\/h2\u003e\n\u003cp\u003eNot every building needs a large tank. A garage workshop with a utility sink, a small office with a kitchenette, a commercial space with a washbasin or a cottage used mostly in summer have modest needs, but they deserve reliable hot water. The \u003cstrong\u003eBradford White RE110U6-1NAL electric water heater\u003c\/strong\u003e meets these uses with a tank of \u003cstrong\u003e10 US gallons (8 imperial gallons, 38 L)\u003c\/strong\u003e, a single \u003cstrong\u003e1,500 W\u003c\/strong\u003e element and a \u003cstrong\u003e120 V\u003c\/strong\u003e supply. AirGreen installs it in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and on the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch3\u003eThe middle size of the utility line\u003c\/h3\u003e\n\u003cp\u003eBradford White's residential utility line has three compact sizes. The RE110U6-1NAL sits in the middle: more reserve than the very small model designed to hide under a sink, but a much smaller footprint than the largest size in the line. At 17 7\/16 in. tall and 16 in. in diameter, it fits on a workshop floor, in a utility closet or under a deep enough counter. Its weight of 44 lb also makes it easy to carry down a narrow staircase or into an accessible crawl space.\u003c\/p\u003e\n\u003ch3\u003eWhat it is used for\u003c\/h3\u003e\n\u003cp\u003eThis tank is made for occasional needs: washing hands after dirty work, rinsing tools, doing the dishes in an office kitchenette or supplying the sink of a small break room. In a business, it can serve a washbasin and a utility sink located in the same spot. It is not designed for a daily shower or to replace a home's water heater; for those uses, we offer you a standard-size residential tank.\u003c\/p\u003e\n\u003ch3\u003eManufacturer data\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003eCapacity:\u003c\/strong\u003e 10 US gallons, 8 imperial gallons, 38 L.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eFactory configuration:\u003c\/strong\u003e 120 V, single 1,500 W element, unless otherwise specified.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eRecovery:\u003c\/strong\u003e 7 US gal\/h or 6 imp. gal\/h at a 90 °F rise; 26 L\/h at a 50 °C rise, based on 1,500 W.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eElement:\u003c\/strong\u003e immersion, screw-in, copper, with an INCOLOY-type element available on request.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eConnections:\u003c\/strong\u003e water and electrical in 3\/4 in. (19 mm) NPT, factory-installed dielectric fittings.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eTank protection:\u003c\/strong\u003e Vitraglas with Microban lining.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eHeight:\u003c\/strong\u003e 17 7\/16 in. (443 mm); \u003cstrong\u003ediameter:\u003c\/strong\u003e 16 in. (404 mm).\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 44 lb (20 kg).\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eVoltage and wattage: the available options\u003c\/h3\u003e\n\u003cp\u003eThe RE110U6-1NAL is factory-wired for 120 V with a 1,500 W element, so it can be fed by an ordinary 120 V circuit reserved for the unit. Bradford White offers the series in 120 V, 208 V, 240 V, 277 V and 480 V, single-phase only. Its limitations table covers wattages from 1,500 W to 6,000 W depending on the voltage; at 120 V, only wattages from 1,500 W to 3,000 W are allowed. A different configuration must be specified when ordering. In a workshop where a 240 V panel is already in place, we assess with you whether another combination is useful, but the factory configuration suits most of the uses described here.\u003c\/p\u003e\n\u003ch3\u003eRecovery suited to occasional needs\u003c\/h3\u003e\n\u003cp\u003eAt 1,500 W, the element heats 7 US gallons per hour for a 90 °F rise. In practical terms, the 10 US gallon reserve is rebuilt in under an hour and a half after being completely drained, which works well for uses spread out over the day. For continuous use, such as repeatedly filling a large tub, a larger size or a different wattage would be more appropriate.\u003c\/p\u003e\n\u003ch3\u003eConstruction and compliance\u003c\/h3\u003e\n\u003cp\u003eThe tank is protected by the \u003cstrong\u003eVitraglas with Microban\u003c\/strong\u003e lining, and the copper immersion element screws into the tank, which makes it easy to replace. The factory-installed dielectric fittings separate the steel of the tank from the copper of the piping. Bradford White states that all models in the series are UL listed, and that applicable models are verified by CSA for energy performance under standard C191.1-M90.\u003c\/p\u003e\n\u003ch3\u003eManufacturer's warranty\u003c\/h3\u003e\n\u003cp\u003eThis model has a 6-year limited warranty on the tank and 6 years on parts. The full terms are attached to the quote.\u003c\/p\u003e\n\u003ch2\u003eAirGreen installs your RE110U6-1NAL cleanly and by the rules\u003c\/h2\u003e\n\u003cp\u003eAirGreen is a family-owned heating and cooling company established in Montreal, active for more than fifteen years and holding RBQ licence 5645-9605-01 (ventilation, refrigeration and electrical). We start with a \u003cstrong\u003efree on-site estimate\u003c\/strong\u003e, then give you a \u003cstrong\u003ewritten quote\u003c\/strong\u003e. Installation includes:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eassessing the location, access to the connections and protection against freezing;\u003c\/li\u003e\n\u003cli\u003edraining and removing the old tank, where applicable;\u003c\/li\u003e\n\u003cli\u003econnecting the cold and hot water in 3\/4 in. NPT;\u003c\/li\u003e\n\u003cli\u003einstalling the relief valve and its discharge line to a safe location;\u003c\/li\u003e\n\u003cli\u003ethe electrical connection on a 120 V circuit reserved for the unit;\u003c\/li\u003e\n\u003cli\u003efilling the tank completely, powering it up and setting the temperature;\u003c\/li\u003e\n\u003cli\u003emaintenance advice and, if needed, seasonal draining instructions.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eLightly heated buildings and cottages\u003c\/h3\u003e\n\u003cp\u003eIn a garage or cottage that is not heated year-round, the water in the tank and piping can freeze during the Quebec winter and damage the tank. If the building stays cold for several weeks, we show you how to cut the power, shut off the water and drain the tank completely before the cold season, then how to fill it before powering it up again in spring. For a heated building, one partial flush per year and a test of the relief valve are enough.\u003c\/p\u003e\n\u003ch3\u003eService area\u003c\/h3\u003e\n\u003cp\u003eWe work in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, Mirabel, Kirkland, Dollard-des-Ormeaux, Beloeil, Saint-Constant and everywhere on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e. If the installation is part of a larger project, our \u003ca href=\"\/en\/pages\/financement-avec-financeit\"\u003efinancing\u003c\/a\u003e lets you spread out the cost.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRequest your free estimate for the Bradford White RE110U6-1NAL.\u003c\/strong\u003e Tell us where hot water is needed and attach a photo of the intended location: we will reply with a clear recommendation.\u003c\/p\u003e","brand":"Bradford White","offers":[{"title":"Default Title","offer_id":67799686447396,"sku":"RE110U6-1NAL","price":0.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0715\/1694\/6724\/files\/CHAUFFE_EAU_ELECTRIQUE_BRADFORD_WHITE_RE1_UTILITAIRE_RE110U6_1NAL_10_GAL_US_00_MONTREAL_LAVAL_LONGUEUIL_RIVE_SUD_RIVE_NORD.png?v=1793082266"},{"product_id":"chauffe-eau-electrique-bradford-white-re220u6-1nal-18-gallons-montreal-laval-longueuil-rive-sud-rive-nord","title":"BRADFORD WHITE RE220U6-1NAL Electric Water Heater (18 gallons) | Montreal, Laval, Longueuil, South Shore \u0026 North Shore","description":"\u003ch2\u003eThe largest of the compact 120 V tanks, for a secondary bathroom or a small cottage\u003c\/h2\u003e\n\u003cp\u003eSome needs fall between the small water heater hidden under a sink and a home's main tank: a guest bathroom at the far end of the basement, a cottage used on weekends, a studio built above a garage or a small commercial space with a kitchenette and a washroom. The \u003cstrong\u003eBradford White RE220U6-1NAL electric water heater\u003c\/strong\u003e targets exactly this middle ground, with a reserve of \u003cstrong\u003e18 US gallons (15 imperial gallons, 68 L)\u003c\/strong\u003e, a \u003cstrong\u003e1,500 W\u003c\/strong\u003e element and a \u003cstrong\u003e120 V\u003c\/strong\u003e supply. AirGreen installs it in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and on the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch3\u003eThe largest size in the utility line\u003c\/h3\u003e\n\u003cp\u003eThe RE220U6-1NAL is the largest of the three compact sizes in Bradford White's residential utility line. It keeps the strengths of this line, namely a 120 V supply and a single element, but with a noticeably more generous reserve than the small sink models. At 26 1\/4 in. tall and 20 in. in diameter, it remains low enough to fit under a staircase, in a bathroom closet or in the corner of a crowded mechanical room.\u003c\/p\u003e\n\u003ch3\u003eA short shower, yes; a whole house, no\u003c\/h3\u003e\n\u003cp\u003eLet us be clear about what this size can do. Its reserve handles handwashing and dishes with ease, and a short shower in a guest bathroom or a cottage. After heavy use, the 1,500 W element reheats the water at a rate of 7 US gallons per hour for a 90 °F rise: it therefore takes some time before the reserve is full again. For a family taking several showers in a row, or as the main water heater of a dwelling, we recommend a full-size residential tank instead.\u003c\/p\u003e\n\u003ch3\u003eManufacturer data\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003eCapacity:\u003c\/strong\u003e 18 US gallons, 15 imperial gallons, 68 L.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eFactory wiring:\u003c\/strong\u003e 120 V with a 1,500 W element, unless otherwise specified.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eNumber of elements:\u003c\/strong\u003e one only.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eRecovery:\u003c\/strong\u003e 7 US gal\/h (6 imp. gal\/h) at a 90 °F rise; 26 L\/h at a 50 °C rise, based on 1,500 W.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eElement:\u003c\/strong\u003e immersion, screw-in, copper; INCOLOY-type element on request.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eConnections:\u003c\/strong\u003e 3\/4 in. (19 mm) NPT for water and electrical, factory-installed dielectric fittings.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eLining:\u003c\/strong\u003e Vitraglas with Microban.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eDimensions:\u003c\/strong\u003e 26 1\/4 in. (667 mm) tall, 20 in. (508 mm) in diameter.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 67 1\/2 lb.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eA simple 120 V supply\u003c\/h3\u003e\n\u003cp\u003eThe main advantage of this model in a secondary building is its power supply. Factory-wired for 120 V and 1,500 W, it only needs a 120 V circuit reserved for the unit, where a full-size tank would require a two-pole 240 V circuit. In a cottage or garage with a limited electrical panel, this greatly simplifies the work. Bradford White also offers the series in 208 V, 240 V, 277 V and 480 V, single-phase only, with wattages from 1,500 W to 6,000 W according to its limitations table; at 120 V, the wattage stays between 1,500 W and 3,000 W. Any configuration other than the factory one is specified when ordering.\u003c\/p\u003e\n\u003ch3\u003eKeep the full weight in mind\u003c\/h3\u003e\n\u003cp\u003eEmpty, the tank weighs 67 1\/2 lb. Once filled with its 68 L of water, it becomes much heavier, which rules out a light shelf or a fragile mezzanine floor. We check the support at the intended location and provide a drain pan when the tank is installed above a finished room, to protect the ceiling in case of a leak.\u003c\/p\u003e\n\u003ch3\u003eConstruction and compliance\u003c\/h3\u003e\n\u003cp\u003eLike the other models in the line, the RE220U6-1NAL receives Bradford White's \u003cstrong\u003eVitraglas with Microban\u003c\/strong\u003e lining. Its copper immersion element screws into the tank, and the factory-installed dielectric fittings limit corrosion where the tank meets the piping. According to the manufacturer, all models are UL listed and applicable models are verified by CSA for energy performance under standard C191.1-M90.\u003c\/p\u003e\n\u003ch3\u003eManufacturer's warranty\u003c\/h3\u003e\n\u003cp\u003eBradford White gives this model a 6-year limited warranty on the tank and 6 years on parts. The full terms come with the quote.\u003c\/p\u003e\n\u003ch2\u003eInstallation of the RE220U6-1NAL by AirGreen in Greater Montreal\u003c\/h2\u003e\n\u003cp\u003eAirGreen is a family-owned heating and cooling company established in Montreal and active for more than fifteen years. Our electrical connections are made under RBQ licence 5645-9605-01 (ventilation, refrigeration and electrical). After a \u003cstrong\u003efree on-site estimate\u003c\/strong\u003e, we give you a \u003cstrong\u003ewritten quote\u003c\/strong\u003e. Installation includes:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eassessing the location, the support and the access for maintenance;\u003c\/li\u003e\n\u003cli\u003edraining and removing the old water heater, where applicable;\u003c\/li\u003e\n\u003cli\u003econnecting the cold and hot water in 3\/4 in. NPT;\u003c\/li\u003e\n\u003cli\u003einstalling the relief valve, its discharge line and, if needed, a drain pan;\u003c\/li\u003e\n\u003cli\u003ethe 120 V electrical connection on a reserved circuit;\u003c\/li\u003e\n\u003cli\u003efilling the tank before powering it up, then setting the temperature;\u003c\/li\u003e\n\u003cli\u003emaintenance advice suited to occasional or seasonal use.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eMaintenance and seasonal use\u003c\/h3\u003e\n\u003cp\u003eA partial flush once a year removes the sediment that builds up at the bottom and extends the life of the element. We also recommend operating the relief valve during this visit to check that it opens and closes properly. In a cottage closed for the winter, the tank must be powered down and fully drained before the frost, then filled before being powered up again in spring: we show you the procedure during installation.\u003c\/p\u003e\n\u003ch3\u003eService area\u003c\/h3\u003e\n\u003cp\u003eWe install this model in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, as well as in Lorraine, Bois-des-Filion, Sainte-Anne-des-Plaines, Saint-Basile-le-Grand, Mont-Saint-Hilaire and everywhere on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e. Our \u003ca href=\"\/en\/pages\/financement-avec-financeit\"\u003efinancing\u003c\/a\u003e program can apply if the installation is part of a larger project.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRequest your free estimate for the Bradford White RE220U6-1NAL.\u003c\/strong\u003e A photo of the intended location and of the electrical panel lets us propose the right solution from the first visit.\u003c\/p\u003e","brand":"Bradford White","offers":[{"title":"Default Title","offer_id":67799691460900,"sku":"RE220U6-1NAL","price":0.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0715\/1694\/6724\/files\/CHAUFFE_EAU_ELECTRIQUE_BRADFORD_WHITE_RE1_UTILITAIRE_RE220U6_1NAL_18_GAL_US_00_MONTREAL_LAVAL_LONGUEUIL_RIVE_SUD_RIVE_NORD.png?v=1793082266"},{"product_id":"chauffe-eau-electrique-bradford-white-re230s6-1ncpp-27-gallons-montreal-laval-longueuil-rive-sud-rive-nord","title":"BRADFORD WHITE RE230S6-1NCPP Electric Water Heater (27 gallons) | Montreal, Laval, Longueuil, South Shore \u0026 North Shore","description":"\u003ch2\u003eA 27 US gallon electric water heater, sized for condos and small apartments\u003c\/h2\u003e\n\u003cp\u003eA single person or a couple does not need a large family tank. A unit that is too big keeps hot water in reserve for nothing and takes up valuable space in a condo or apartment. The \u003cstrong\u003eBradford White RE230S6-1NCPP electric water heater\u003c\/strong\u003e offers a reserve of \u003cstrong\u003e27 US gallons (22 imperial gallons, 102 L)\u003c\/strong\u003e, well matched to these needs, with the proven construction of Bradford White residential tanks. AirGreen installs it in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and on the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch3\u003eWho this size is designed for\u003c\/h3\u003e\n\u003cp\u003eThe RE230S6-1NCPP suits a studio, a one- or two-bedroom condo, a plex apartment occupied by one or two people, or a cottage used regularly. In these situations, hot water use is moderate and spread throughout the day: a morning shower, the dishes, a few loads of laundry a week. A 102 L reserve covers these uses comfortably. For a family with children, or if two showers are often taken one after the other, we steer you toward a larger size instead.\u003c\/p\u003e\n\u003ch3\u003eHow this tank heats water\u003c\/h3\u003e\n\u003cp\u003eThe RE230S6-1NCPP heats water with immersion electric elements screwed into the tank. Cold water enters the bottom of the tank and hot water leaves from the top. When you draw hot water, the upper part is reheated first, then heating switches to the lower part. In the non-simultaneous configuration, the default one, the elements never heat at the same time. This proven operation explains the longevity of this type of unit and how simple it is to maintain.\u003c\/p\u003e\n\u003ch3\u003eManufacturer data\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003eCapacity:\u003c\/strong\u003e 27 US gallons, 22 imperial gallons, 102 L.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eStandby loss:\u003c\/strong\u003e 53 W.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eConnections:\u003c\/strong\u003e all water and electrical connections are 3\/4 in. (19 mm) NPT, with factory-installed dielectric fittings.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eInternal lining:\u003c\/strong\u003e Vitraglas with Microban.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eElements:\u003c\/strong\u003e immersion, screw-in type.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eOperation:\u003c\/strong\u003e non-simultaneous by default; simultaneous operation available, to be specified when ordering.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eAvailable voltages:\u003c\/strong\u003e 120 V, 208 V, 240 V, 277 V and 480 V; at 120 V and 277 V, single-phase only.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 90 lb (41 kg).\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eListings:\u003c\/strong\u003e UL; approved for manufactured homes under CAN\/CSA Z240 MH series.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eA 53 W standby loss: what it means\u003c\/h3\u003e\n\u003cp\u003eA tank keeps its water hot at all times, even when nobody is using it. Standby loss measures the heat it gives off to the room during these periods. For the RE230S6-1NCPP, Bradford White publishes a standby loss of 53 W: the equivalent of a small light bulb left on continuously. A low standby loss means the elements restart less often to maintain the temperature, which is especially useful in a small home where hot water often sits unused during the working day.\u003c\/p\u003e\n\u003ch3\u003eLocation and dimensions\u003c\/h3\u003e\n\u003cp\u003eIn a condo or apartment, the water heater is usually in a utility closet or the laundry room. The RE230S6-1NCPP weighs 90 lb empty, which makes it easy to handle on an indoor staircase or in a service elevator. Its exact dimensions are confirmed before ordering, and we always measure the available space, the ceiling height and the clearance in front of the elements during the assessment. If height is very limited, we can offer you a low tank of similar capacity.\u003c\/p\u003e\n\u003ch3\u003ePower supply\u003c\/h3\u003e\n\u003cp\u003eThe exact element wattage of the unit ordered is confirmed with the order and shown in your quote; it sets the size of the breaker and conductors. Bradford White offers this model in several voltages, but in a Quebec condo or apartment, the water heater is normally fed by a two-pole 240 V circuit. Simultaneous operation must be requested when ordering; the default non-simultaneous configuration suits the vast majority of small homes, since it limits the current drawn from the panel.\u003c\/p\u003e\n\u003ch3\u003eThe right temperature setting\u003c\/h3\u003e\n\u003cp\u003eWith a small tank, it is sometimes tempting to raise the temperature to stretch the reserve. This setting should stay cautious: water that is too hot increases the risk of scalding at the tap, while water that is too lukewarm in the tank is not recommended for hygiene reasons. At commissioning, we set the thermostat according to current recommendations and, if you want a hotter reserve, we can add a thermostatic mixing valve at the outlet.\u003c\/p\u003e\n\u003ch3\u003eManufacturer's warranty\u003c\/h3\u003e\n\u003cp\u003eThe RE230S6-1NCPP is covered by a 6-year limited warranty on the tank and 6 years on parts. The full terms come with your quote.\u003c\/p\u003e\n\u003ch2\u003eInstallation of the RE230S6-1NCPP by AirGreen\u003c\/h2\u003e\n\u003cp\u003eAirGreen is a family-owned heating and cooling company established in Montreal and active for more than fifteen years. Our electrical work is done under RBQ licence 5645-9605-01 (ventilation, refrigeration and electrical). After a \u003cstrong\u003efree on-site estimate\u003c\/strong\u003e, you receive a \u003cstrong\u003ewritten quote\u003c\/strong\u003e. Installation includes:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003echecking the location, access and the drain or drain pan;\u003c\/li\u003e\n\u003cli\u003edraining, disconnecting and removing the old tank;\u003c\/li\u003e\n\u003cli\u003econnecting the cold and hot water in 3\/4 in. NPT;\u003c\/li\u003e\n\u003cli\u003einstalling the relief valve and its discharge line;\u003c\/li\u003e\n\u003cli\u003ethe electrical connection according to the confirmed wattage;\u003c\/li\u003e\n\u003cli\u003efilling the tank before powering it up, then setting the temperature;\u003c\/li\u003e\n\u003cli\u003emaintenance advice: annual partial flush, relief valve test, anode inspection.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eReplace it before it fails\u003c\/h3\u003e\n\u003cp\u003eA water heater often gives warning signs before it gives out: rust-tinted hot water, crackling noises while heating, moisture or a whitish deposit at the base of the tank, water that cools faster than before. In a condo, waiting for a leak can cause damage in the unit below. If you notice any of these signs, send us a photo of your tank's nameplate: we will tell you frankly whether it is time to replace it.\u003c\/p\u003e\n\u003ch3\u003eService area\u003c\/h3\u003e\n\u003cp\u003eWe work in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, Griffintown, Old Montreal, Côte-des-Neiges, Nuns' Island, Saint-Lambert and everywhere on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e. Payment can be spread out through our \u003ca href=\"\/en\/pages\/financement-avec-financeit\"\u003efinancing\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRequest your free estimate for the Bradford White RE230S6-1NCPP.\u003c\/strong\u003e A photo of your current tank and its closet lets us prepare the visit and the quote.\u003c\/p\u003e","brand":"Bradford White","offers":[{"title":"Default Title","offer_id":67799694082340,"sku":"RE230S6-1NCPP","price":0.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0715\/1694\/6724\/files\/CHAUFFE_EAU_ELECTRIQUE_BRADFORD_WHITE_RE230S6_1NCPP_27_GAL_US_00_MONTREAL_LAVAL_LONGUEUIL_RIVE_SUD_RIVE_NORD.png?v=1793082265"},{"product_id":"chauffe-eau-electrique-bradford-white-re230ln6-1ncpp-27-gallons-montreal-laval-longueuil-rive-sud-rive-nord","title":"BRADFORD WHITE RE230LN6-1NCPP Electric Water Heater (27 gallons) | Montreal, Laval, Longueuil, South Shore \u0026 North Shore","description":"\u003ch2\u003eA 102 L electric water heater low enough for places where a standard tank will not fit\u003c\/h2\u003e\n\u003cp\u003eIn a condo, a plex apartment or a cottage, the water heater often hides under a staircase, in a low closet or in a nook where height is lacking. An ordinary upright tank simply does not fit there. The \u003cstrong\u003eBradford White RE230LN6-1NCPP electric water heater\u003c\/strong\u003e was designed for these situations: it holds \u003cstrong\u003e102 L\u003c\/strong\u003e of hot water in a tank only \u003cstrong\u003e29 9\/16 in. tall\u003c\/strong\u003e, wider and squatter than a standard model. AirGreen installs it in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and on the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch3\u003eA low, wide format\u003c\/h3\u003e\n\u003cp\u003eThe RE230LN6-1NCPP measures 29 9\/16 in. (751 mm) in height for a diameter of 23 in. (584 mm). These proportions let it slip under the steps of a staircase, under a laundry room shelf or into the utility closet of a condo, where a tall, narrow tank would be blocked by the ceiling. In return, it takes up a little more floor space: we therefore measure the available space, the clearance in front of the element access panel and the path to the location before confirming the model.\u003c\/p\u003e\n\u003ch3\u003eWho it is for\u003c\/h3\u003e\n\u003cp\u003eA 102 L reserve suits a single person or a couple, in a condo, a small apartment or a cottage. It is also a good choice for replacing an old low-height tank without having to modify the cabinet or closet around it. For a family with children or a house with several bathrooms, we look instead at a larger size in the same family, or at a standard tank if the height allows.\u003c\/p\u003e\n\u003cp\u003eWith a reserve of this size, a few habits make a real difference: spacing out the shower and the dishwasher, washing laundry in cold water when possible and keeping a reasonable set temperature. At commissioning, we adjust the thermostat to your use and show you how to change it safely.\u003c\/p\u003e\n\u003ch3\u003eManufacturer data\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003eCapacity:\u003c\/strong\u003e 102 L.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eDimensions:\u003c\/strong\u003e height of 29 9\/16 in. (751 mm), diameter of 23 in. (584 mm).\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 102 lb (46 kg).\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eConnections:\u003c\/strong\u003e all water and electrical connections are 3\/4 in. (19 mm) NPT.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eInternal lining:\u003c\/strong\u003e Vitraglas with Microban.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eElements:\u003c\/strong\u003e immersion, screw-in, copper; INCOLOY-type element available on request.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eOperation:\u003c\/strong\u003e non-simultaneous by default; simultaneous operation available, to be specified when ordering.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eAvailable voltages:\u003c\/strong\u003e 120 V, 208 V, 240 V, 277 V and 480 V; at 120 V and 277 V, single-phase wiring only.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eDrain valve:\u003c\/strong\u003e brass, low-restriction, tamper-resistant design.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eScrew-in elements, wattage confirmed with the order\u003c\/h3\u003e\n\u003cp\u003eThe RE230LN6-1NCPP heats water with immersion electric elements screwed directly into the tank. In non-simultaneous mode, the default configuration, only one element runs at a time, which limits the current drawn from the panel. The exact element wattage of the unit ordered is confirmed with the order and shown on your quote; it determines the size of the breaker and conductors. If you want simultaneous operation, it must be specified at the time of ordering.\u003c\/p\u003e\n\u003ch3\u003eWhich voltage for your home\u003c\/h3\u003e\n\u003cp\u003eBradford White offers this model in several voltages. In a Quebec house or condo, the water heater is usually fed by a two-pole 240 V circuit; the other voltages are used mainly in commercial buildings or special cases. We check the existing supply, the condition of the circuit and the panel capacity, then confirm the configuration before ordering the unit.\u003c\/p\u003e\n\u003ch3\u003eMaterials and easier maintenance\u003c\/h3\u003e\n\u003cp\u003eThe tank is protected by Bradford White's \u003cstrong\u003eVitraglas with Microban\u003c\/strong\u003e lining. The copper elements can be replaced with INCOLOY-type elements on request, a useful option when the water is particularly hard. The \u003cstrong\u003elow-restriction brass drain valve\u003c\/strong\u003e, with a tamper-resistant design, makes fast, thorough draining easier, a real advantage during annual maintenance.\u003c\/p\u003e\n\u003ch3\u003eListings and manufactured homes\u003c\/h3\u003e\n\u003cp\u003eAccording to the manufacturer, all models in the series are UL listed. The RE230LN6-1NCPP is also approved for installation in manufactured homes, under standard CAN\/CSA Z240 MH series. Its low height makes it a natural candidate for a tiny home or a mobile home, where technical space is very limited.\u003c\/p\u003e\n\u003ch3\u003eManufacturer's warranty\u003c\/h3\u003e\n\u003cp\u003eThis model is covered by a 6-year limited warranty on the tank and 6 years on parts. The full terms come with your quote.\u003c\/p\u003e\n\u003ch2\u003eInstallation of the Bradford White RE230LN6-1NCPP by AirGreen\u003c\/h2\u003e\n\u003cp\u003eAirGreen is a family-owned heating and cooling company established in Montreal, active for more than fifteen years. Electrical connections are made under our RBQ licence 5645-9605-01, which covers ventilation, refrigeration and electrical work. After a \u003cstrong\u003efree on-site estimate\u003c\/strong\u003e, you receive a \u003cstrong\u003ewritten quote\u003c\/strong\u003e. Installation includes:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003emeasuring the location, the access clearance for the elements and the path;\u003c\/li\u003e\n\u003cli\u003edraining, disconnecting and removing the old tank;\u003c\/li\u003e\n\u003cli\u003econnecting the cold and hot water in 3\/4 in. NPT;\u003c\/li\u003e\n\u003cli\u003einstalling the relief valve and its discharge line;\u003c\/li\u003e\n\u003cli\u003ethe electrical connection according to the confirmed wattage, and a check of the breaker;\u003c\/li\u003e\n\u003cli\u003efilling the tank completely before powering it up, then setting the temperature;\u003c\/li\u003e\n\u003cli\u003emaintenance advice: partial flushing, relief valve test, anode check.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIn a condo: protecting the neighbours below\u003c\/h3\u003e\n\u003cp\u003eIn a condominium, a leaking water heater can damage several units. We install the tank on a drain pan connected to a drain whenever possible, and we check every fitting for leaks at commissioning. Some condo boards also require a leak detector or an automatic shut-off valve; we can include this in the quote if your by-laws call for it.\u003c\/p\u003e\n\u003ch3\u003eService area\u003c\/h3\u003e\n\u003cp\u003eWe work in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, the Plateau-Mont-Royal, Rosemont, Verdun, Brossard, Sainte-Rose and everywhere on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e. Our \u003ca href=\"\/en\/pages\/financement-avec-financeit\"\u003efinancing\u003c\/a\u003e program lets you spread out the payment if you wish.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRequest your free estimate for the Bradford White RE230LN6-1NCPP.\u003c\/strong\u003e Send us a photo of your current tank along with the measurements of the space: height, width and depth.\u003c\/p\u003e","brand":"Bradford White","offers":[{"title":"Default Title","offer_id":67799694115108,"sku":"RE230LN6-1NCPP","price":0.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0715\/1694\/6724\/files\/CHAUFFE_EAU_ELECTRIQUE_BRADFORD_WHITE_RE2_LOWBOY_RE230LN6_1NCPP_102_L_00_MONTREAL_LAVAL_LONGUEUIL_RIVE_SUD_RIVE_NORD.png?v=1793082266"},{"product_id":"chauffe-eau-electrique-bradford-white-re240s6-1ncpp-38-gallons-montreal-laval-longueuil-rive-sud-rive-nord","title":"BRADFORD WHITE RE240S6-1NCPP Electric Water Heater (38 gallons) | Montreal, Laval, Longueuil, South Shore \u0026 North Shore","description":"\u003ch2\u003eA 38 US gallon tank for a couple or a young family, installed before the old one gives out\u003c\/h2\u003e\n\u003cp\u003eThe water heater is the appliance everyone forgets until the day it leaks. For a couple or a young family living in a townhouse, a semi-detached home or a roomy condo, the \u003cstrong\u003eBradford White RE240S6-1NCPP electric water heater\u003c\/strong\u003e is a simple, durable replacement: a reserve of \u003cstrong\u003e38 US gallons (32 imperial gallons, 140 L)\u003c\/strong\u003e, a tank protected by the \u003cstrong\u003eVitraglas with Microban\u003c\/strong\u003e lining and a 6-year warranty on the tank and on parts. AirGreen installs it in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and on the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch3\u003eThe size for townhouses and semi-detached homes\u003c\/h3\u003e\n\u003cp\u003eWith a 140 L reserve, the RE240S6-1NCPP meets the needs of two or three people sharing a main bathroom well. It leaves enough hot water for a shower, a dishwasher and a load of laundry in the same evening, without the volume of a large family tank that would heat water for nothing. If the house has two bathrooms used in the morning or the family is growing, a larger capacity is worth considering; we discuss it during the assessment.\u003c\/p\u003e\n\u003ch3\u003eAfter a pre-purchase inspection or a question from the insurer\u003c\/h3\u003e\n\u003cp\u003eMany homeowners replace their water heater following a pre-purchase inspection report that notes an old tank, or because their insurer asks for the unit's age at renewal. In both cases, it is better to plan the replacement than to suffer it. A planned replacement happens on the date that suits you, without water damage, and gives you time to compare options, for example between a conventional electric tank and a heat pump water heater.\u003c\/p\u003e\n\u003ch3\u003eConventional tank or heat pump\u003c\/h3\u003e\n\u003cp\u003eA heat pump water heater uses less electricity, but it needs a room large enough to supply it with air, a drain for condensate water and more height. In a townhouse or condo where the water heater sits in a closed closet, these conditions are rarely met. A conventional electric tank like the RE240S6-1NCPP can then be installed almost anywhere, runs silently and needs very little maintenance. During the assessment, we look at the space with you and recommend the solution that truly suits your home.\u003c\/p\u003e\n\u003ch3\u003eThe manufacturer's data\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003eCapacity:\u003c\/strong\u003e 38 US gallons, 32 imperial gallons, 140 L.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eStandby loss:\u003c\/strong\u003e 61 W.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eConnections:\u003c\/strong\u003e water and electrical in 3\/4 in. (19 mm) NPT; factory-installed dielectric fittings.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eLining:\u003c\/strong\u003e Vitraglas with Microban.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eElements:\u003c\/strong\u003e immersion, screw-in type.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eOperation:\u003c\/strong\u003e non-simultaneous by default; simultaneous available, to be specified when ordering.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eAvailable voltages:\u003c\/strong\u003e 120 V, 208 V, 240 V, 277 V, 480 V; 120 V and 277 V single-phase only.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 123 lb (56 kg).\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eListings:\u003c\/strong\u003e all models are UL listed; installation approved in manufactured homes under CAN\/CSA Z240 MH series.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat makes a tank last\u003c\/h3\u003e\n\u003cp\u003eThree construction details matter for the life of an electric water heater. First, the internal lining: Bradford White's Vitraglas with Microban isolates the steel of the tank from the water. Next, the factory-installed dielectric fittings on the 3\/4 in. NPT connections, which separate the steel of the tank from the copper of the plumbing and limit galvanic corrosion. Finally, the screw-in immersion elements: when an element wears out, it can be replaced without touching the tank.\u003c\/p\u003e\n\u003ch3\u003eA 61 W standby loss\u003c\/h3\u003e\n\u003cp\u003eBradford White publishes a standby loss of 61 W for this model, meaning the heat the tank gives off to the room on average when nobody is using hot water. This value reflects the quality of the insulation around the tank. The lower it is, the less the elements need to restart to maintain the temperature between uses. In a cool basement, we also insulate the first few feet of hot water piping to keep that heat where it belongs.\u003c\/p\u003e\n\u003ch3\u003eElectrical supply and configuration\u003c\/h3\u003e\n\u003cp\u003eThe RE240S6-1NCPP is configured by default for non-simultaneous operation: its elements heat one after the other, never together. Simultaneous operation exists, but it must be specified when ordering. The element wattage of the unit ordered is confirmed with the order and written in your quote, because it determines the breaker and the conductor size. In a house, the unit is fed by a two-pole 240 V circuit; we check that the existing circuit is suitable before reusing it.\u003c\/p\u003e\n\u003ch3\u003eManufacturer's warranty\u003c\/h3\u003e\n\u003cp\u003eBradford White gives the RE240S6-1NCPP a 6-year limited warranty on the tank and 6 years on parts. The detailed terms are provided with the quote.\u003c\/p\u003e\n\u003ch2\u003eYour planned replacement with AirGreen\u003c\/h2\u003e\n\u003cp\u003eAirGreen is a family-owned heating and cooling company established in Montreal, active for more than fifteen years and holding RBQ licence 5645-9605-01 (ventilation, refrigeration and electrical). After a \u003cstrong\u003efree on-site estimate\u003c\/strong\u003e, we give you a \u003cstrong\u003ewritten quote\u003c\/strong\u003e and set the date that suits you. Installation includes:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eassessing the location, the available height and the nearest drain;\u003c\/li\u003e\n\u003cli\u003edraining, disconnecting and removing the old tank;\u003c\/li\u003e\n\u003cli\u003econnecting the cold and hot water in 3\/4 in. NPT;\u003c\/li\u003e\n\u003cli\u003einstalling a new relief valve and its discharge line;\u003c\/li\u003e\n\u003cli\u003ethe electrical connection according to the confirmed wattage;\u003c\/li\u003e\n\u003cli\u003efilling the tank, purging air at the taps and powering up;\u003c\/li\u003e\n\u003cli\u003esetting the temperature and our maintenance advice.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eChecks you can do yourself\u003c\/h3\u003e\n\u003cp\u003eBetween maintenance visits, a few quick looks are enough. Check the base of the tank and the floor around it from time to time: any sign of moisture deserves a call. Make sure the relief valve line is not dripping, and keep the space in front of the unit clear for maintenance. Once a year, a partial flush and an anode inspection extend the life of the tank; we can take care of them during a visit.\u003c\/p\u003e\n\u003ch3\u003eService area\u003c\/h3\u003e\n\u003cp\u003eWe work in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, Auteuil, Fabreville, Lachine, Saint-Bruno, Sainte-Julie and everywhere on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e. If you want to spread out the payment, our \u003ca href=\"\/en\/pages\/financement-avec-financeit\"\u003efinancing\u003c\/a\u003e is presented with the quote.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eSchedule your free estimate for the Bradford White RE240S6-1NCPP.\u003c\/strong\u003e A photo of your current tank and its nameplate lets us prepare an accurate quote.\u003c\/p\u003e","brand":"Bradford White","offers":[{"title":"Default Title","offer_id":67799697522980,"sku":"RE240S6-1NCPP","price":0.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0715\/1694\/6724\/files\/CHAUFFE_EAU_ELECTRIQUE_BRADFORD_WHITE_RE240S6_1NCPP_38_GAL_US_00_MONTREAL_LAVAL_LONGUEUIL_RIVE_SUD_RIVE_NORD.png?v=1793082265"},{"product_id":"chauffe-eau-electrique-bradford-white-re240ln6-1ncpp-37-gallons-montreal-laval-longueuil-rive-sud-rive-nord","title":"BRADFORD WHITE RE240LN6-1NCPP Electric Water Heater (37 gallons) | Montreal, Laval, Longueuil, South Shore \u0026 North Shore","description":"\u003ch2\u003e140 L of hot water in a low tank, for basements where every inch of height counts\u003c\/h2\u003e\n\u003cp\u003eMany homes in the region have a low basement: exposed beams, ventilation ducts under the joists, a ceiling rebuilt too low during a renovation. When it is time to replace the water heater, the usual upright tank no longer fits. The \u003cstrong\u003eBradford White RE240LN6-1NCPP electric water heater\u003c\/strong\u003e offers a \u003cstrong\u003e140 L\u003c\/strong\u003e reserve in a tank \u003cstrong\u003e32 1\/16 in. tall\u003c\/strong\u003e, designed for these spaces. AirGreen installs it in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and on the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch3\u003eA reserve for a couple or a small family\u003c\/h3\u003e\n\u003cp\u003eWith its 140 L, the RE240LN6-1NCPP sits in the middle of this family of low tanks. It suits a couple, or a small family whose showers do not all happen at the same time. It is also a very good replacement for an old low tank at the end of its life, with no need to move the plumbing or modify a ceiling. If the family grows or the house has two bathrooms used in the morning, we compare it with the next size up before making a recommendation.\u003c\/p\u003e\n\u003ch3\u003eHow the tank heats water\u003c\/h3\u003e\n\u003cp\u003eAn electric storage water heater keeps a reserve of hot water ready for use. When you open a tap, hot water leaves from the top and cold water enters the bottom of the tank. The upper thermostat responds first and heats the top of the tank, to quickly restore hot water to the taps; once that zone is up to temperature, heating switches to the lower element, which reheats the rest of the reserve. In the non-simultaneous configuration, it is always one or the other, never both at once. This simple principle explains the reliability of this type of unit and how easy it is to maintain.\u003c\/p\u003e\n\u003ch3\u003eManufacturer data\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003eCapacity:\u003c\/strong\u003e 140 L.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eHeight:\u003c\/strong\u003e 32 1\/16 in. (814 mm).\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eDiameter:\u003c\/strong\u003e 24 1\/2 in. (622 mm).\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 126 lb (57 kg).\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eConnections:\u003c\/strong\u003e water and electrical in 3\/4 in. (19 mm) NPT.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eLining:\u003c\/strong\u003e Vitraglas with Microban.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eElements:\u003c\/strong\u003e immersion, screw-in, copper; INCOLOY on request.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eConfiguration:\u003c\/strong\u003e non-simultaneous by default; simultaneous as an option, to be specified when ordering.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eVoltages offered:\u003c\/strong\u003e 120 V, 208 V, 240 V, 277 V, 480 V; 120 V and 277 V are wired single-phase only.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eDraining:\u003c\/strong\u003e low-restriction brass valve, durable tamper-resistant design.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eThink about access as much as height\u003c\/h3\u003e\n\u003cp\u003eA low tank solves the ceiling issue, but maintenance also has to be planned. The elements of the RE240LN6-1NCPP screw into the tank and are reached through their access panels, so enough clearance must be kept in front of them to replace them one day. At 24 1\/2 in. in diameter, the tank takes up a little more floor space than an upright model. During the assessment, we check the space around the unit, the path down the stairs for its 126 lb and the proximity of a floor drain.\u003c\/p\u003e\n\u003ch3\u003eElectrical: what is confirmed with the order\u003c\/h3\u003e\n\u003cp\u003eThe default configuration is non-simultaneous: only one element heats at a time, which keeps the current draw moderate. The exact element wattage of the unit ordered is confirmed with the order and written on the quote, because it sets the size of the breaker and conductors. Bradford White offers this model in 120 V, 208 V, 240 V, 277 V and 480 V; in a house, the usual supply is a two-pole 240 V circuit. If the old tank's circuit is in good condition and matches the confirmed wattage, it can be reused.\u003c\/p\u003e\n\u003ch3\u003eA drain valve that makes maintenance easier\u003c\/h3\u003e\n\u003cp\u003eThe RE240LN6-1NCPP is equipped with a \u003cstrong\u003elow-restriction brass drain valve\u003c\/strong\u003e with a durable tamper-resistant design. In a low, wide tank, sediment spreads over a large bottom; a valve that allows a good flow clears it more effectively during the annual flush. It is a detail that matters in areas where the water is hard.\u003c\/p\u003e\n\u003ch3\u003eLining and elements\u003c\/h3\u003e\n\u003cp\u003eThe tank is protected by Bradford White's \u003cstrong\u003eVitraglas with Microban\u003c\/strong\u003e lining. The copper immersion elements can be replaced with INCOLOY-type elements on request. Since they are screwed in, a faulty element can be changed without replacing the tank, a routine and quick job.\u003c\/p\u003e\n\u003ch3\u003eStandards and listings\u003c\/h3\u003e\n\u003cp\u003eBradford White states that all models in the series are UL listed and that this model is approved for installation in manufactured homes under standard CAN\/CSA Z240 MH series.\u003c\/p\u003e\n\u003ch3\u003eManufacturer's warranty\u003c\/h3\u003e\n\u003cp\u003eThe RE240LN6-1NCPP is covered by a 6-year limited warranty on the tank and 6 years on parts. The detailed terms are provided with the quote.\u003c\/p\u003e\n\u003ch2\u003eReplacement of your low tank by AirGreen\u003c\/h2\u003e\n\u003cp\u003eAirGreen is a family-owned heating and cooling company established in Montreal and active for more than fifteen years. We work under RBQ licence 5645-9605-01 (ventilation, refrigeration and electrical). After a \u003cstrong\u003efree on-site estimate\u003c\/strong\u003e, you receive a \u003cstrong\u003ewritten quote\u003c\/strong\u003e. The replacement includes:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003emeasuring the headroom, the service clearance and the path to the basement;\u003c\/li\u003e\n\u003cli\u003efully draining, disconnecting and removing the old tank;\u003c\/li\u003e\n\u003cli\u003esetting the new tank level on a suitable base;\u003c\/li\u003e\n\u003cli\u003econnecting the cold and hot water in 3\/4 in. NPT;\u003c\/li\u003e\n\u003cli\u003einstalling the relief valve and its discharge line to the drain;\u003c\/li\u003e\n\u003cli\u003ethe electrical connection according to the confirmed wattage;\u003c\/li\u003e\n\u003cli\u003efilling, purging air at the taps, powering up and setting the temperature;\u003c\/li\u003e\n\u003cli\u003emaintenance advice, including the annual flush and an anode check.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIf your current tank is leaking\u003c\/h3\u003e\n\u003cp\u003eA low tank installed in a finished basement can cause damage quickly. If you see water at its base, switch off the water heater breaker, close the cold water valve at the tank inlet, then contact us. We tell you what to do next and schedule the replacement as soon as possible.\u003c\/p\u003e\n\u003ch3\u003eService area\u003c\/h3\u003e\n\u003cp\u003eWe serve \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, Ahuntsic, Villeray, Pointe-aux-Trembles, Greenfield Park, Chomedey and the whole \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and \u003cstrong\u003eNorth Shore\u003c\/strong\u003e. Payment can be spread out with our \u003ca href=\"\/en\/pages\/financement-avec-financeit\"\u003efinancing\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRequest your free estimate for the Bradford White RE240LN6-1NCPP.\u003c\/strong\u003e A photo of your current tank and the headroom under the joists are enough to prepare the visit.\u003c\/p\u003e","brand":"Bradford White","offers":[{"title":"Default Title","offer_id":67799697588516,"sku":"RE240LN6-1NCPP","price":0.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0715\/1694\/6724\/files\/CHAUFFE_EAU_ELECTRIQUE_BRADFORD_WHITE_RE2_LOWBOY_RE240LN6_1NCPP_140_L_00_MONTREAL_LAVAL_LONGUEUIL_RIVE_SUD_RIVE_NORD.png?v=1793082266"},{"product_id":"chauffe-eau-electrique-bradford-white-re250s6-1ncpp-47-gallons-montreal-laval-longueuil-rive-sud-rive-nord","title":"BRADFORD WHITE RE250S6-1NCPP Electric Water Heater (47 gallons) | Montreal, Laval, Longueuil, South Shore \u0026 North Shore","description":"\u003ch2\u003eThe 47 US gallon family reserve for the basement of a single-family home\u003c\/h2\u003e\n\u003cp\u003eIn a bungalow, a cottage-style house or a two-storey home in Greater Montreal, the electric water heater in the basement supplies the kitchen, the bathroom, the powder room and the laundry room. When it reaches the end of its life, it has to be replaced with a reliable unit of good capacity that does not require redoing the installation. The \u003cstrong\u003eBradford White RE250S6-1NCPP electric water heater\u003c\/strong\u003e meets this need with a reserve of \u003cstrong\u003e47 US gallons (39 imperial gallons, 178 L)\u003c\/strong\u003e, a tank lined with \u003cstrong\u003eVitraglas with Microban\u003c\/strong\u003e and a 6-year limited warranty on the tank and on parts. AirGreen installs it in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and on the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch3\u003eOne family, one bathroom and one powder room\u003c\/h3\u003e\n\u003cp\u003eA 178 L reserve suits a family of three or four sharing a main bathroom and a powder room. It allows two showers in the morning, the dishwasher in the evening and a few loads of laundry during the week without running out of hot water, as long as everything does not happen at exactly the same moment. If the house has several full bathrooms or a large tub, we will offer you a larger size.\u003c\/p\u003e\n\u003ch3\u003eHow the tank keeps up with the morning rush\u003c\/h3\u003e\n\u003cp\u003eWhen the first shower starts, hot water leaves from the top of the tank and cold water enters at the bottom. The upper thermostat responds and the upper element first rebuilds a zone of hot water near the outlet. Once that zone is up to temperature, heating switches to the lower element, which reheats the rest of the volume. Since the RE250S6-1NCPP is configured for non-simultaneous operation by default, only one element heats at a time. This mechanism is what allows a tank of this size to keep up with a normal family routine.\u003c\/p\u003e\n\u003ch3\u003eManufacturer specifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003eCapacity:\u003c\/strong\u003e 47 US gallons, 39 imperial gallons, 178 L.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eStandby loss:\u003c\/strong\u003e 59 W.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eConnections:\u003c\/strong\u003e 3\/4 in. (19 mm) NPT for water and electrical, factory-installed dielectric fittings.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eLining:\u003c\/strong\u003e Vitraglas with Microban.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eElements:\u003c\/strong\u003e immersion, screw-in type.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eOperation:\u003c\/strong\u003e non-simultaneous by default; simultaneous available, to be specified when ordering.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eVoltages:\u003c\/strong\u003e 120 V, 208 V, 240 V, 277 V or 480 V; 120 V and 277 V single-phase only.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 143 lb (65 kg).\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eListings:\u003c\/strong\u003e UL; approved for manufactured homes under CAN\/CSA Z240 MH series.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eInsulation that holds the heat\u003c\/h3\u003e\n\u003cp\u003eThe 59 W standby loss published by Bradford White represents the heat the tank loses on average when it is not in use. It is a good indicator of the tank's insulation. In a home where nobody is in during the day, hot water stays in reserve for long hours: a moderate standby loss limits the number of times the elements have to restart to maintain the temperature.\u003c\/p\u003e\n\u003ch3\u003eWeight and handling\u003c\/h3\u003e\n\u003cp\u003eEmpty, the RE250S6-1NCPP weighs 143 lb. Two technicians with a suitable hand truck carry it without difficulty, but the basement stairs, doors and turns must allow it. We measure these passages during the assessment, and we confirm the unit's dimensions before ordering to make sure it fits where the old tank stood.\u003c\/p\u003e\n\u003ch3\u003eStandard fittings for a clean replacement\u003c\/h3\u003e\n\u003cp\u003eThe water and electrical connections of the RE250S6-1NCPP are 3\/4 in. NPT, a common format in homes in the region. In most replacements, the existing piping therefore connects without major work. The factory-installed dielectric fittings separate the steel of the tank from the copper of the plumbing, which limits corrosion at the joint. When we find old fittings or a worn shut-off valve, we replace them during the same visit rather than leaving them to fail later.\u003c\/p\u003e\n\u003ch3\u003eWhat the electrical panel must supply\u003c\/h3\u003e\n\u003cp\u003eIn a house, this type of tank is fed by a two-pole 240 V circuit. The exact element wattage of the unit ordered is confirmed with the order and written in your quote; it determines the size of the breaker and conductors. In non-simultaneous operation, the demand on the panel remains that of a single element. If you want simultaneous operation, it must be specified when ordering and the panel capacity must be checked.\u003c\/p\u003e\n\u003ch3\u003eManufacturer's warranty\u003c\/h3\u003e\n\u003cp\u003eThe RE250S6-1NCPP is covered by a 6-year limited warranty on the tank and 6 years on parts. The full terms are provided with the quote.\u003c\/p\u003e\n\u003ch2\u003eReplacement of your water heater by AirGreen\u003c\/h2\u003e\n\u003cp\u003eAirGreen is a family-owned heating and cooling company established in Montreal and active for more than fifteen years. We hold RBQ licence 5645-9605-01 in ventilation, refrigeration and electrical work. After a \u003cstrong\u003efree on-site estimate\u003c\/strong\u003e, you receive a \u003cstrong\u003ewritten quote\u003c\/strong\u003e. On the day of the work, we proceed in this order:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eshutting off the circuit and the water supply, then draining the old tank;\u003c\/li\u003e\n\u003cli\u003edisconnecting and removing the old unit;\u003c\/li\u003e\n\u003cli\u003esetting the RE250S6-1NCPP level, in the same location or in a better-suited one;\u003c\/li\u003e\n\u003cli\u003econnecting the cold and hot water in 3\/4 in. NPT;\u003c\/li\u003e\n\u003cli\u003einstalling a new relief valve and its discharge line;\u003c\/li\u003e\n\u003cli\u003ethe electrical connection according to the confirmed wattage;\u003c\/li\u003e\n\u003cli\u003efilling completely, purging air at the taps, powering up and setting the temperature;\u003c\/li\u003e\n\u003cli\u003eexplaining the maintenance and the checks to carry out.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eExtending the life of your tank\u003c\/h3\u003e\n\u003cp\u003eA few simple steps help a water heater last. A partial flush once a year removes the sediment that insulates the lower element and causes crackling. The anode protects the tank by wearing away in its place: inspecting it regularly allows it to be replaced before it is used up. Water pressure that is too high at the house entrance also strains the tank; if we find it excessive, we offer you a pressure-reducing valve.\u003c\/p\u003e\n\u003ch3\u003eService area\u003c\/h3\u003e\n\u003cp\u003eWe install this model in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, as well as in Pierrefonds, Duvernay, Saint-Vincent-de-Paul, Saint-Lambert, Varennes and throughout the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e. Our \u003ca href=\"\/en\/pages\/financement-avec-financeit\"\u003efinancing\u003c\/a\u003e program lets you spread out the payment.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRequest your free estimate for the Bradford White RE250S6-1NCPP.\u003c\/strong\u003e Send us a photo of your current tank, its nameplate and the basement stairs.\u003c\/p\u003e","brand":"Bradford White","offers":[{"title":"Default Title","offer_id":67799701192996,"sku":"RE250S6-1NCPP","price":0.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0715\/1694\/6724\/files\/CHAUFFE_EAU_ELECTRIQUE_BRADFORD_WHITE_RE250S6_1NCPP_47_GAL_US_00_MONTREAL_LAVAL_LONGUEUIL_RIVE_SUD_RIVE_NORD.png?v=1793082265"},{"product_id":"chauffe-eau-electrique-bradford-white-re250t6-1ncpp-47-gallons-montreal-laval-longueuil-rive-sud-rive-nord","title":"BRADFORD WHITE RE250T6-1NCPP Electric Water Heater (47 gallons) | Montreal, Laval, Longueuil, South Shore \u0026 North Shore","description":"\u003ch2\u003eA reliable 47 US gallon tank for rental units and plexes in Greater Montreal\u003c\/h2\u003e\n\u003cp\u003eIn a duplex, a triplex or a small apartment building, each unit often has its own water heater. For the owner, a tank that gives out on a Saturday night means a tenant without hot water, possible water damage and an emergency call. The \u003cstrong\u003eBradford White RE250T6-1NCPP electric water heater\u003c\/strong\u003e is a solid choice for these replacements: a reserve of \u003cstrong\u003e47 US gallons (39 imperial gallons, 178 L)\u003c\/strong\u003e, a tank protected by the \u003cstrong\u003eVitraglas with Microban\u003c\/strong\u003e lining and a 6-year limited warranty on the tank and on parts. AirGreen installs it in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and on the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch3\u003eThe water heater of a plex apartment\u003c\/h3\u003e\n\u003cp\u003eA five- or six-room apartment occupied by a family calls for a family-size reserve. With its 178 L, the RE250T6-1NCPP covers the everyday needs of a household of three or four, without the bulk of a large tank that would crowd the unit's closet or laundry room. Empty, it weighs 130 lb (59 kg), a weight that is easy to manoeuvre on the indoor staircases and narrow hallways typical of Montreal plexes.\u003c\/p\u003e\n\u003ch3\u003ePlanning replacements in a building\u003c\/h3\u003e\n\u003cp\u003eWhen several units were equipped at the same time, their water heaters age together. Rather than waiting for failures one by one, many owners prefer to plan the replacements: one unit at a change of tenant, another during a renovation, starting with the oldest tanks. We can tour the building, note the age and condition of each unit, and propose a realistic schedule in a single written quote.\u003c\/p\u003e\n\u003ch3\u003eManufacturer data\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003eCapacity:\u003c\/strong\u003e 47 US gallons, 39 imperial gallons, 178 L.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eStandby loss:\u003c\/strong\u003e 63 W.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eConnections:\u003c\/strong\u003e 3\/4 in. (19 mm) NPT for water and electrical; factory-installed dielectric fittings.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eLining:\u003c\/strong\u003e Vitraglas with Microban.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eElements:\u003c\/strong\u003e immersion, screw-in type.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eOperation:\u003c\/strong\u003e non-simultaneous by default; simultaneous available, to be specified when ordering.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eVoltages:\u003c\/strong\u003e 120 V, 208 V, 240 V, 277 V, 480 V; 120 V and 277 V single-phase only.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 130 lb (59 kg).\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eListings:\u003c\/strong\u003e UL; approved for manufactured homes under CAN\/CSA Z240 MH series.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eA 63 W standby loss\u003c\/h3\u003e\n\u003cp\u003eStandby loss indicates the heat the tank loses on average when it is not being used. For the RE250T6-1NCPP, Bradford White publishes 63 W. In an apartment where hot water is used mostly in the morning and evening, this value determines how often the elements must restart during the day. When the tank is installed in an unheated closet or near an outside wall, we insulate the accessible hot water piping to limit losses.\u003c\/p\u003e\n\u003ch3\u003eA unit that is simple to maintain\u003c\/h3\u003e\n\u003cp\u003eFor an owner, simplicity matters. The immersion elements of the RE250T6-1NCPP screw into the tank: a burnt-out element is replaced in a short visit, without changing the tank. The factory-installed dielectric fittings limit corrosion between the steel of the tank and the copper of the plumbing, a frequent cause of leaks at the fittings in older buildings. The Vitraglas with Microban lining protects the inside of the tank.\u003c\/p\u003e\n\u003ch3\u003eProtecting the unit below\u003c\/h3\u003e\n\u003cp\u003eIn a plex, the water heater of an upper unit sits directly above another apartment. A leak, even a slow one, can then damage a ceiling and disturb two households at once. During the replacement, we install the tank on a drain pan when space allows, route the relief valve line to a safe discharge point and check the condition of the shut-off valves. These precautions are easy to include at installation time and avoid many claims later on.\u003c\/p\u003e\n\u003ch3\u003eElectrical supply in plexes\u003c\/h3\u003e\n\u003cp\u003eIn a plex, each water heater is usually connected to the panel of the unit it serves, through a two-pole 240 V circuit. Some older panels have limited capacity; the default non-simultaneous configuration, where only one element heats at a time, helps keep demand reasonable. The exact element wattage of the unit ordered is confirmed with the order and written in the quote, and we check the breaker and conductors of each unit before installation.\u003c\/p\u003e\n\u003ch3\u003eManufacturer's warranty\u003c\/h3\u003e\n\u003cp\u003eThe RE250T6-1NCPP is covered by a 6-year limited warranty on the tank and 6 years on parts. For each unit, we give you the invoice and the serial number of the installed tank, which simplifies warranty follow-up in a building.\u003c\/p\u003e\n\u003ch2\u003eAirGreen replaces the water heaters in your units\u003c\/h2\u003e\n\u003cp\u003eAirGreen is a family-owned heating and cooling company established in Montreal, active for more than fifteen years and holding RBQ licence 5645-9605-01 (ventilation, refrigeration and electrical). After a \u003cstrong\u003efree on-site estimate\u003c\/strong\u003e, you receive a \u003cstrong\u003ewritten quote\u003c\/strong\u003e, per unit or for the building. For each unit, installation includes:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003echecking the location, the drain or drain pan and the access;\u003c\/li\u003e\n\u003cli\u003edraining, disconnecting and removing the old tank;\u003c\/li\u003e\n\u003cli\u003econnecting the cold and hot water in 3\/4 in. NPT;\u003c\/li\u003e\n\u003cli\u003einstalling a new relief valve and its discharge line;\u003c\/li\u003e\n\u003cli\u003ethe electrical connection according to the confirmed wattage;\u003c\/li\u003e\n\u003cli\u003efilling, purging air at the taps, powering up and setting the temperature;\u003c\/li\u003e\n\u003cli\u003emaintenance recommendations: annual partial flush, relief valve test, anode inspection.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCoordinating with your tenants\u003c\/h3\u003e\n\u003cp\u003eA water heater replacement leaves the unit without hot water for only a few hours. We agree on a time slot with you, you can notify your tenants in advance, and we leave the premises clean. If several units are involved, we do them one after the other to limit trips and disruption.\u003c\/p\u003e\n\u003ch3\u003eService area\u003c\/h3\u003e\n\u003cp\u003eWe work in \u003cstrong\u003eMontreal\u003c\/strong\u003e, including Rosemont, Villeray, Hochelaga, Saint-Henri and Verdun, as well as in \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e and everywhere on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e. For a project involving several units, our \u003ca href=\"\/en\/pages\/financement-avec-financeit\"\u003efinancing\u003c\/a\u003e lets you spread out the investment.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRequest your free estimate for the Bradford White RE250T6-1NCPP.\u003c\/strong\u003e Tell us the number of units and send a photo of each tank's nameplate: we will prepare a clear quote for the building.\u003c\/p\u003e","brand":"Bradford White","offers":[{"title":"Default Title","offer_id":67799701225764,"sku":"RE250T6-1NCPP","price":0.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0715\/1694\/6724\/files\/CHAUFFE_EAU_ELECTRIQUE_BRADFORD_WHITE_RE250T6_1NCPP_47_GAL_US_00_MONTREAL_LAVAL_LONGUEUIL_RIVE_SUD_RIVE_NORD.png?v=1793082266"},{"product_id":"chauffe-eau-electrique-bradford-white-re250s10-1ncpp-47-gallons-montreal-laval-longueuil-rive-sud-rive-nord","title":"BRADFORD WHITE RE250S10-1NCPP Electric Water Heater (47 gallons) | Montreal, Laval, Longueuil, South Shore \u0026 North Shore","description":"\u003ch2\u003eThe extended-warranty version of the 47 US gallon tank, for homeowners who plan ahead\u003c\/h2\u003e\n\u003cp\u003eWhen you plan to stay in your home for a long time, you choose a water heater differently. You look less at day one than at the years that follow: the quality of the tank, ease of maintenance and the manufacturer's coverage. The \u003cstrong\u003eBradford White RE250S10-1NCPP electric water heater\u003c\/strong\u003e is the extended-warranty version of Bradford White's \u003cstrong\u003e47 US gallon (39 imperial gallon, 178 L)\u003c\/strong\u003e residential tank. It shares the capacity and construction of the standard version, with longer coverage. AirGreen installs it in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and on the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch3\u003eWhat the \"10\" suffix means\u003c\/h3\u003e\n\u003cp\u003eIn Bradford White's model numbering, the figure following the model letter indicates the warranty category. The manufacturer specifies that, to get the extended-warranty version of a tank in this series, the \"6\" suffix is replaced with \"10\". The RE250S10-1NCPP is therefore the extended-warranty version of this capacity. The exact split of coverage between the tank and the parts is confirmed in writing with your quote, so you know precisely what is covered before ordering.\u003c\/p\u003e\n\u003ch3\u003eWhich homes it suits\u003c\/h3\u003e\n\u003cp\u003eWith a 178 L reserve, this tank suits a family of three or four sharing a main bathroom and a powder room. The extended-warranty version appeals mostly to homeowners who have just bought and plan to stay, those renovating their basement who do not want to touch it again, or duplex owners who live in one of the units and want fewer surprises. In a home to be sold in the short term, the standard version is often enough.\u003c\/p\u003e\n\u003ch3\u003eManufacturer data\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003eCapacity:\u003c\/strong\u003e 47 US gallons, 39 imperial gallons, 178 L.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eStandby loss:\u003c\/strong\u003e 59 W.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eConnections:\u003c\/strong\u003e 3\/4 in. (19 mm) NPT for water and electrical, with factory-installed dielectric fittings.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eInternal lining:\u003c\/strong\u003e Vitraglas with Microban.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eElements:\u003c\/strong\u003e immersion, screw-in type.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eOperation:\u003c\/strong\u003e non-simultaneous by default; simultaneous available, to be specified when ordering.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eAvailable voltages:\u003c\/strong\u003e 120 V, 208 V, 240 V, 277 V, 480 V; 120 V and 277 V wired single-phase only.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 143 lb (65 kg).\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eListings:\u003c\/strong\u003e all models are UL listed; installation approved in manufactured homes under CAN\/CSA Z240 MH series.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eConstruction designed to last\u003c\/h3\u003e\n\u003cp\u003eThe tank is protected by the \u003cstrong\u003eVitraglas with Microban\u003c\/strong\u003e lining, which isolates the steel from the water. The factory-installed dielectric fittings on the 3\/4 in. connections separate the steel of the tank from the copper of the piping, a joint where corrosion often starts. The immersion elements are screwed in: when an element wears out, it can be replaced without changing the tank, which is exactly what you expect from a unit kept for a long time.\u003c\/p\u003e\n\u003ch3\u003eA 59 W standby loss\u003c\/h3\u003e\n\u003cp\u003eBradford White publishes a standby loss of 59 W for this model. This value measures the heat the tank gives off to the room when idle; it depends mostly on the insulation around the tank. A moderate loss means fewer heating cycles to maintain the temperature. To go further, we insulate the accessible hot water piping near the tank, a simple improvement that keeps the water in the lines hot for longer.\u003c\/p\u003e\n\u003ch3\u003eWater quality and service life\u003c\/h3\u003e\n\u003cp\u003eOver the long term, water quality matters as much as the tank's construction. Hard water leaves sediment at the bottom of the tank and scales the elements; softened water, on the other hand, wears the anode faster. If your home is supplied by a well or equipped with a water softener, we adjust the frequency of flushing and anode inspections accordingly. It is a small adjustment that makes a real difference to the life of a tank you plan to keep for a long time.\u003c\/p\u003e\n\u003ch3\u003eElectrical connection\u003c\/h3\u003e\n\u003cp\u003eThe factory configuration is non-simultaneous: only one element heats at a time. Simultaneous operation is available, but it must be requested when ordering. The exact element wattage of the unit ordered is confirmed with the order and written in your quote, because it determines the breaker and the conductor size. In a house, the tank is fed by a two-pole 240 V circuit, which we check before reusing it.\u003c\/p\u003e\n\u003ch3\u003eMaking a warranty claim when the time comes\u003c\/h3\u003e\n\u003cp\u003eAn extended warranty is only worth something if you can make a claim. Keep your installation invoice and note the serial number on the nameplate; this is the information usually requested when making a claim. Regular maintenance, such as an annual partial flush and an anode inspection, also helps keep the unit in good condition throughout the coverage period.\u003c\/p\u003e\n\u003ch2\u003eInstallation of the RE250S10-1NCPP by AirGreen\u003c\/h2\u003e\n\u003cp\u003eAirGreen is a family-owned heating and cooling company established in Montreal, active for more than fifteen years and holding RBQ licence 5645-9605-01 (ventilation, refrigeration and electrical). After a \u003cstrong\u003efree on-site estimate\u003c\/strong\u003e, you receive a \u003cstrong\u003ewritten quote\u003c\/strong\u003e that also specifies the manufacturer's coverage. Installation includes:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eassessing the location, the access path and the drain;\u003c\/li\u003e\n\u003cli\u003edraining, disconnecting and removing the old tank;\u003c\/li\u003e\n\u003cli\u003econnecting the cold and hot water in 3\/4 in. NPT;\u003c\/li\u003e\n\u003cli\u003einstalling a new relief valve and its discharge line;\u003c\/li\u003e\n\u003cli\u003ethe electrical connection according to the confirmed wattage;\u003c\/li\u003e\n\u003cli\u003efilling, purging air, powering up and setting the temperature;\u003c\/li\u003e\n\u003cli\u003ehanding over the warranty documents and our maintenance advice.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eNew construction and major renovation\u003c\/h3\u003e\n\u003cp\u003eIn new construction or a complete renovation, the water heater deserves its place from the planning stage: an accessible room, a floor drain nearby and enough clearance in front of the elements. We can coordinate the installation with your contractor so the tank arrives at the right time, once the rough plumbing and electrical are ready.\u003c\/p\u003e\n\u003ch3\u003eService area\u003c\/h3\u003e\n\u003cp\u003eWe work in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, Westmount, Mount Royal, Sainte-Dorothée, Brossard, Carignan and everywhere on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e. Payment can be spread out through our \u003ca href=\"\/en\/pages\/financement-avec-financeit\"\u003efinancing\u003c\/a\u003e.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRequest your free estimate for the Bradford White RE250S10-1NCPP.\u003c\/strong\u003e A photo of your current installation lets us prepare an accurate quote, warranty included.\u003c\/p\u003e","brand":"Bradford White","offers":[{"title":"Default Title","offer_id":67799705714980,"sku":"RE250S10-1NCPP","price":0.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0715\/1694\/6724\/files\/CHAUFFE_EAU_ELECTRIQUE_BRADFORD_WHITE_RE250S10_1NCPP_47_GAL_US_00_MONTREAL_LAVAL_LONGUEUIL_RIVE_SUD_RIVE_NORD.png?v=1793082266"},{"product_id":"chauffe-eau-electrique-bradford-white-re250ln6-1ncpp-45-gallons-montreal-laval-longueuil-rive-sud-rive-nord","title":"BRADFORD WHITE RE250LN6-1NCPP Electric Water Heater (45 gallons) | Montreal, Laval, Longueuil, South Shore \u0026 North Shore","description":"\u003ch2\u003eA 170 L family reserve in a low tank, for homes where the ceiling limits the choice\u003c\/h2\u003e\n\u003cp\u003eA family living in a house with a low basement often faces a dilemma when it is time to change the water heater: upright tanks large enough for them do not fit under the joists, and small low tanks run short of hot water. The \u003cstrong\u003eBradford White RE250LN6-1NCPP electric water heater\u003c\/strong\u003e resolves this dilemma with a \u003cstrong\u003e170 L\u003c\/strong\u003e reserve in a tank \u003cstrong\u003e33 5\/16 in. tall\u003c\/strong\u003e. It is the largest of the low tanks in this Bradford White family that we offer. AirGreen installs it in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and on the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch3\u003eWhen height is short, but needs are not\u003c\/h3\u003e\n\u003cp\u003eThe RE250LN6-1NCPP targets households that use as much hot water as a typical family, for example four people with a main bathroom and a powder room, but whose mechanical room is low. It is found under a mezzanine, in a basement whose ceiling was lowered to hide ducts, in a house on a crawl space or in a cottage lived in year-round. It lets you keep a family-size reserve without tearing down a ceiling or moving the plumbing to another room.\u003c\/p\u003e\n\u003cp\u003eA larger reserve also has a less visible advantage: it leaves more margin when several appliances run at the same time, for example a shower while the dishwasher fills. The temperature stays steadier at the tap, and the tank has time to recover between the morning and evening peaks.\u003c\/p\u003e\n\u003ch3\u003eThe trade-off: wider and heavier\u003c\/h3\u003e\n\u003cp\u003eTo fit 170 L into a low height, the tank gets wider: it measures 26 in. (660 mm) in diameter. It also weighs 173 lb (78 kg) empty, which calls for two people and a suitable hand truck on a basement staircase. Before confirming the model, we measure the width of the stairs and doors, the available floor space and the clearance in front of the elements. If the access is too narrow, we tell you at the assessment and propose another solution.\u003c\/p\u003e\n\u003ch3\u003eManufacturer data\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003eCapacity:\u003c\/strong\u003e 170 L.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eHeight:\u003c\/strong\u003e 33 5\/16 in. (846 mm).\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eDiameter:\u003c\/strong\u003e 26 in. (660 mm).\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 173 lb (78 kg).\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eConnections:\u003c\/strong\u003e 3\/4 in. (19 mm) NPT for water and electrical.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eInternal protection:\u003c\/strong\u003e Vitraglas with Microban lining.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eElements:\u003c\/strong\u003e immersion, screw-in, copper, with an INCOLOY option on request.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eOperation:\u003c\/strong\u003e non-simultaneous by default, simultaneous as an option when ordering.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eAvailable voltages:\u003c\/strong\u003e 120 V, 208 V, 240 V, 277 V, 480 V; 120 V and 277 V single-phase only.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eDrain valve:\u003c\/strong\u003e brass, low-restriction, tamper-resistant design.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSimultaneous or non-simultaneous\u003c\/h3\u003e\n\u003cp\u003eBy default, the RE250LN6-1NCPP is configured for non-simultaneous operation: its elements never heat at the same time, which limits the demand on the home's electrical panel. Simultaneous operation, where the elements can heat together to speed up recovery, is available as an option but must be specified when ordering, because it increases the current draw. In most homes, the default configuration is the most sensible; we discuss it with you based on your panel's capacity.\u003c\/p\u003e\n\u003ch3\u003eElement wattage\u003c\/h3\u003e\n\u003cp\u003eThe exact element wattage of the unit ordered is confirmed with the order and written in your quote. It determines the size of the breaker and conductors, which we check before installation. In a house, this type of tank is fed by a two-pole 240 V circuit; the existing circuit can often be kept if it matches the confirmed wattage.\u003c\/p\u003e\n\u003ch3\u003eYear-round cottages and manufactured homes\u003c\/h3\u003e\n\u003cp\u003eAccording to Bradford White, this model is approved for installation in manufactured homes under standard CAN\/CSA Z240 MH series, and all models in the series are UL listed. Its low format suits factory-built homes and four-season cottages well, where the utility room is often under a staircase or in a finished crawl space.\u003c\/p\u003e\n\u003ch3\u003eTank protection and maintenance\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eVitraglas with Microban\u003c\/strong\u003e lining protects the inside of the tank. The copper immersion elements screw into the tank and can be replaced with INCOLOY-type elements on request. The \u003cstrong\u003elow-restriction brass drain valve\u003c\/strong\u003e clears sediment effectively, which matters in a wide tank where sediment spreads over a large bottom.\u003c\/p\u003e\n\u003ch3\u003eManufacturer's warranty\u003c\/h3\u003e\n\u003cp\u003eThis model is covered by a 6-year limited warranty on the tank and 6 years on parts. The full terms are provided with the quote.\u003c\/p\u003e\n\u003ch2\u003eAirGreen installs your RE250LN6-1NCPP, from assessment to commissioning\u003c\/h2\u003e\n\u003cp\u003eAirGreen is a family-owned heating and cooling company established in Montreal, active for more than fifteen years and holding RBQ licence 5645-9605-01 (ventilation, refrigeration and electrical). Every project starts with a \u003cstrong\u003efree on-site estimate\u003c\/strong\u003e and a \u003cstrong\u003ewritten quote\u003c\/strong\u003e. Installation includes:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eassessing the headroom, floor space, access and the nearest drain;\u003c\/li\u003e\n\u003cli\u003edraining and removing the old tank;\u003c\/li\u003e\n\u003cli\u003emoving the new tank to its location;\u003c\/li\u003e\n\u003cli\u003econnecting the cold and hot water in 3\/4 in. NPT;\u003c\/li\u003e\n\u003cli\u003ethe relief valve and its discharge line;\u003c\/li\u003e\n\u003cli\u003ethe electrical connection according to the confirmed wattage and a check of the circuit;\u003c\/li\u003e\n\u003cli\u003efilling, powering up and setting the temperature;\u003c\/li\u003e\n\u003cli\u003emaintenance advice: annual flush, relief valve test, anode inspection.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eRenovating your basement\u003c\/h3\u003e\n\u003cp\u003eIf the replacement goes along with finishing a basement, it is the right time to plan the mechanical room properly. Avoid enclosing the tank in a closet with no access door, provide a floor drain or a drain pan, and keep space in front of the elements. We can visit the site before the walls go up to show you how much space to reserve.\u003c\/p\u003e\n\u003ch3\u003eService area\u003c\/h3\u003e\n\u003cp\u003eWe install this model in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, as well as in Saint-Léonard, Montréal-Nord, Vimont, Saint-Hubert, Sainte-Catherine and everywhere on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e. Our \u003ca href=\"\/en\/pages\/financement-avec-financeit\"\u003efinancing\u003c\/a\u003e lets you spread out the cost of the project.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRequest your free estimate for the Bradford White RE250LN6-1NCPP.\u003c\/strong\u003e Send us a photo of the location with the height under the joists and the width of the stairs.\u003c\/p\u003e","brand":"Bradford White","offers":[{"title":"Default Title","offer_id":67799705747748,"sku":"RE250LN6-1NCPP","price":0.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0715\/1694\/6724\/files\/CHAUFFE_EAU_ELECTRIQUE_BRADFORD_WHITE_RE2_LOWBOY_RE250LN6_1NCPP_170_L_00_MONTREAL_LAVAL_LONGUEUIL_RIVE_SUD_RIVE_NORD.png?v=1793082266"},{"product_id":"chauffe-eau-electrique-bradford-white-re265t6-1ncww-61-gallons-montreal-laval-longueuil-rive-sud-rive-nord","title":"BRADFORD WHITE RE265T6-1NCWW Electric Water Heater (61 gallons) | Montreal, Laval, Longueuil, South Shore \u0026 North Shore","description":"\u003ch2\u003eWhen the family grows: 61 US gallons of hot water and a 73-gallon first-hour rating\u003c\/h2\u003e\n\u003cp\u003eTeenagers take longer showers, a second bathroom has been added in the basement, and the last person to wash in the morning gets lukewarm water. It is often a sign that the water heater has become too small for the house. The \u003cstrong\u003eBradford White RE265T6-1NCWW electric water heater\u003c\/strong\u003e offers a reserve of \u003cstrong\u003e61 US gallons (51 imperial gallons, 231 L)\u003c\/strong\u003e, two \u003cstrong\u003e4,500 W\u003c\/strong\u003e elements and a \u003cstrong\u003efirst-hour rating of 73 gallons (276 L)\u003c\/strong\u003e. AirGreen installs it in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and on the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch3\u003eSigns you need a larger tank\u003c\/h3\u003e\n\u003cp\u003eA tank that is too small does not break down: it simply runs out of hot water at the wrong times. Showers getting shorter, the dishwasher being put off until the next day, the bath that can no longer be filled after the evening showers are all clues. The RE265T6-1NCWW is aimed at families of four or five, homes with two full bathrooms and households that have added a large tub or a high-flow shower.\u003c\/p\u003e\n\u003cp\u003eOn the other hand, a tank that is too large for the house keeps hot water in reserve for nothing and takes up space. That is why we only recommend this size when the family's habits justify it; for a couple, a smaller tank remains the logical choice.\u003c\/p\u003e\n\u003ch3\u003eUnderstanding the first-hour rating\u003c\/h3\u003e\n\u003cp\u003eThe first-hour rating indicates how much hot water a water heater can supply during one hour of heavy use, starting from a full tank. It combines the reserve with what the elements reheat during that hour. For the RE265T6-1NCWW, Bradford White publishes 73 gallons, or 276 L. To choose the right size, you simply estimate what the household uses during the busiest hour of the day, usually the morning, and choose a unit whose first-hour rating exceeds that need. We do this calculation with you during the assessment, based on your actual habits.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003eCapacity:\u003c\/strong\u003e 61 US gallons, 51 imperial gallons, 231 L.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eFirst-hour rating:\u003c\/strong\u003e 73 gallons (276 L).\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eRecovery:\u003c\/strong\u003e 21 US gal\/h (18 imp. gal\/h) at a 90 °F rise; 79 L\/h at a 50 °C rise, in non-simultaneous 4,500 W\/4,500 W operation.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eFactory wiring:\u003c\/strong\u003e 240 V, single-phase, two interlocked (non-simultaneous) 4,500 W elements, unless otherwise specified.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eStandby loss:\u003c\/strong\u003e 71 W.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eConnections:\u003c\/strong\u003e water and electrical in 3\/4 in. (19 mm) NPT; factory-installed dielectric fittings.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eLining:\u003c\/strong\u003e Vitraglas with Microban.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eElements:\u003c\/strong\u003e immersion, screw-in type.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eOther voltages offered:\u003c\/strong\u003e 120 V, 208 V, 277 V, 480 V; 120 V and 277 V single-phase only.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 156 lb (71 kg).\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eListings:\u003c\/strong\u003e UL; approved for manufactured homes under CAN\/CSA Z240 MH series.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eTwo 4,500 W elements taking turns\u003c\/h3\u003e\n\u003cp\u003eThe RE265T6-1NCWW is factory-wired with two 4,500 W elements that work in turn. When hot water is drawn, the upper element first heats the top of the tank to quickly restore hot water to the taps; the lower element then takes over for the rest of the volume. In this configuration, the manufacturer publishes a recovery of 21 US gallons per hour for a 90 °F rise. This combination of a large reserve and sustained recovery is what gives the model its first-hour rating.\u003c\/p\u003e\n\u003ch3\u003eThe electrical circuit\u003c\/h3\u003e\n\u003cp\u003eThe factory wiring at 240 V single-phase, with interlocked elements, ensures that only one 4,500 W element heats at a time. In most homes, the circuit of an existing electric tank may be suitable, but we always check the breaker, the conductors and the panel capacity before installation. Simultaneous operation also exists, but it must be specified when ordering and significantly increases the load on the panel; it is rarely justified in a house.\u003c\/p\u003e\n\u003ch3\u003eStandby loss and insulation\u003c\/h3\u003e\n\u003cp\u003eBradford White publishes a standby loss of 71 W for this model. This is the heat the large reserve gives off to the room when it is not being used. A larger tank holds more hot water and therefore has a larger surface exchanging heat with the surrounding air; this is normal. To limit losses on the way to the taps, we insulate the accessible hot water piping near the unit.\u003c\/p\u003e\n\u003ch3\u003eManufacturer's warranty\u003c\/h3\u003e\n\u003cp\u003eThe RE265T6-1NCWW is covered by a 6-year limited warranty on the tank and 6 years on parts. The full terms are provided with the quote.\u003c\/p\u003e\n\u003ch2\u003eInstallation of the RE265T6-1NCWW by AirGreen\u003c\/h2\u003e\n\u003cp\u003eAirGreen is a family-owned heating and cooling company established in Montreal and active for more than fifteen years. Our electrical connections are made under RBQ licence 5645-9605-01 (ventilation, refrigeration and electrical). After a \u003cstrong\u003efree on-site estimate\u003c\/strong\u003e, you receive a \u003cstrong\u003ewritten quote\u003c\/strong\u003e. Installation includes:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eassessing your peak-hour hot water needs;\u003c\/li\u003e\n\u003cli\u003echecking the location, the access path and the drain;\u003c\/li\u003e\n\u003cli\u003edraining and removing the old tank;\u003c\/li\u003e\n\u003cli\u003econnecting the cold and hot water in 3\/4 in. NPT;\u003c\/li\u003e\n\u003cli\u003ea new relief valve and its discharge line;\u003c\/li\u003e\n\u003cli\u003ethe 240 V electrical connection and a check of the breaker;\u003c\/li\u003e\n\u003cli\u003efilling, purging air, powering up and setting the temperature;\u003c\/li\u003e\n\u003cli\u003emaintenance advice: annual partial flush, relief valve test, anode inspection.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eMoving from a small to a large tank\u003c\/h3\u003e\n\u003cp\u003eReplacing a tank with a larger model takes a little preparation. The RE265T6-1NCWW weighs 156 lb empty and takes up more space than a mid-size tank; its exact dimensions are confirmed before ordering, and we measure the headroom, the floor space and the stairs during the assessment. The existing 3\/4 in. piping usually connects without major modification.\u003c\/p\u003e\n\u003ch3\u003eService area\u003c\/h3\u003e\n\u003cp\u003eWe install this model in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, as well as in Kirkland, Beaconsfield, Laval-des-Rapides, Saint-Bruno, Beloeil and everywhere on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e. Our \u003ca href=\"\/en\/pages\/financement-avec-financeit\"\u003efinancing\u003c\/a\u003e lets you spread out the payment for your project.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRequest your free estimate for the Bradford White RE265T6-1NCWW.\u003c\/strong\u003e Tell us how many people live in the house and send a photo of your current tank: we will confirm whether this size is the right one.\u003c\/p\u003e","brand":"Bradford White","offers":[{"title":"Default Title","offer_id":67799709253924,"sku":"RE265T6-1NCWW","price":0.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0715\/1694\/6724\/files\/CHAUFFE_EAU_ELECTRIQUE_BRADFORD_WHITE_RE265T6_1NCWW_61_GAL_US_00_MONTREAL_LAVAL_LONGUEUIL_RIVE_SUD_RIVE_NORD.png?v=1793082266"},{"product_id":"chauffe-eau-electrique-bradford-white-re265t10-1ncww-61-gallons-montreal-laval-longueuil-rive-sud-rive-nord","title":"BRADFORD WHITE RE265T10-1NCWW Electric Water Heater (61 gallons) | Montreal, Laval, Longueuil, South Shore \u0026 North Shore","description":"\u003ch2\u003eA large 61 US gallon reserve, in an extended-warranty version, for high-demand homes\u003c\/h2\u003e\n\u003cp\u003eSome homes need a lot of hot water in a short time: a deep tub in the main bathroom, a rain shower, two full bathrooms and a powder room, a family of five getting ready at the same time in the morning. The \u003cstrong\u003eBradford White RE265T10-1NCWW electric water heater\u003c\/strong\u003e is designed for this pace, with a reserve of \u003cstrong\u003e61 US gallons (51 imperial gallons, 231 L)\u003c\/strong\u003e, two \u003cstrong\u003e4,500 W\u003c\/strong\u003e elements and a \u003cstrong\u003efirst-hour rating of 73 gallons (276 L)\u003c\/strong\u003e. Its \"10\" suffix makes it the extended-warranty version of this size. AirGreen installs it in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and on the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e.\u003c\/p\u003e\n\u003ch3\u003eHigh-demand homes\u003c\/h3\u003e\n\u003cp\u003eWhat wears out a water heater is not a full day's use, but the peaks. Filling a large tub and then running two or three showers in a row quickly empties a mid-size tank. The RE265T10-1NCWW is aimed at homes where these peaks are frequent: new houses with several bathrooms, extended houses, or large families who have already known cold showers with their old unit.\u003c\/p\u003e\n\u003ch3\u003eWhat the first-hour rating means in practice\u003c\/h3\u003e\n\u003cp\u003eBradford White publishes a first-hour rating of 73 gallons (276 L) for this model. This value adds the stored hot water to the water the elements reheat during one hour of intensive use. In practice, it gives a good idea of what the house can draw during its morning or evening peak without running short. During the assessment, we compare this rating with your peak consumption, based on the number of showers, baths and appliances used during the same hour.\u003c\/p\u003e\n\u003ch3\u003eManufacturer data\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003eCapacity:\u003c\/strong\u003e 61 US gallons, 51 imperial gallons, 231 L.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eFirst-hour rating:\u003c\/strong\u003e 73 gallons, or 276 L.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eRecovery:\u003c\/strong\u003e 21 US gal\/h or 18 imp. gal\/h at a 90 °F rise; 79 L\/h at a 50 °C rise, in non-simultaneous 4,500 W\/4,500 W operation.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eFactory configuration:\u003c\/strong\u003e 240 V single-phase, two 4,500 W elements wired interlocked (non-simultaneous), unless otherwise specified.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eStandby loss:\u003c\/strong\u003e 71 W.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eConnections:\u003c\/strong\u003e 3\/4 in. (19 mm) NPT for water and electrical; factory-installed dielectric fittings.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eLining:\u003c\/strong\u003e Vitraglas with Microban.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eElements:\u003c\/strong\u003e immersion, screw-in type.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eVoltages offered:\u003c\/strong\u003e 120 V, 208 V, 240 V, 277 V, 480 V; 120 V and 277 V single-phase only.\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 156 lb (71 kg).\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eListings:\u003c\/strong\u003e UL; installation approved in manufactured homes under CAN\/CSA Z240 MH series.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eA recovery of 21 US gallons per hour\u003c\/h3\u003e\n\u003cp\u003eAfter a peak, what matters is how quickly the hot water comes back. With its 4,500 W elements taking turns, the RE265T10-1NCWW reheats 21 US gallons per hour for a 90 °F rise, or 79 L\/h for a 50 °C rise. The upper element responds first, so hot water is available again at the top of the tank well before the whole reserve is rebuilt. For a family, this means a house that recovers between the morning routine and the evening one.\u003c\/p\u003e\n\u003ch3\u003eSimultaneous or interlocked\u003c\/h3\u003e\n\u003cp\u003eThe factory wiring interlocks the elements: only one heats at a time. Bradford White also offers simultaneous operation, to be specified when ordering, in which both elements can heat together. This option doubles the current draw and requires a matching circuit and panel. In a house, the interlocked configuration is almost always the best: it already delivers the recovery published by the manufacturer, without overloading the electrical installation. The breaker and conductors are checked during the assessment.\u003c\/p\u003e\n\u003ch3\u003eConstruction for heavy use\u003c\/h3\u003e\n\u003cp\u003eA tank that works hard must be well protected. The tank receives Bradford White's \u003cstrong\u003eVitraglas with Microban\u003c\/strong\u003e lining; the factory-installed dielectric fittings on the 3\/4 in. connections limit corrosion between steel and copper; and the screw-in immersion elements can be replaced without touching the tank. With a published standby loss of 71 W, the large reserve holds its heat well between peaks.\u003c\/p\u003e\n\u003ch3\u003eThe extended warranty of the \"10\" suffix\u003c\/h3\u003e\n\u003cp\u003eBradford White distinguishes its versions by the model suffix: the manufacturer states that the \"6\" suffix is replaced with \"10\" for the extended-warranty version. The RE265T10-1NCWW is therefore the extended-warranty version of the 61 US gallon size. The exact durations that apply to the tank and to parts are confirmed in writing with the quote, before any order.\u003c\/p\u003e\n\u003ch2\u003eInstallation of the RE265T10-1NCWW by AirGreen\u003c\/h2\u003e\n\u003cp\u003eAirGreen is a family-owned heating and cooling company established in Montreal, active for more than fifteen years and holding RBQ licence 5645-9605-01 (ventilation, refrigeration and electrical). Every project begins with a \u003cstrong\u003efree on-site estimate\u003c\/strong\u003e and a \u003cstrong\u003ewritten quote\u003c\/strong\u003e. Installation includes:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003ecalculating your peak consumption and confirming the size;\u003c\/li\u003e\n\u003cli\u003eassessing the location, floor space, headroom and drain;\u003c\/li\u003e\n\u003cli\u003edraining and removing the old tank, or preparing the space in new construction;\u003c\/li\u003e\n\u003cli\u003econnecting the cold and hot water in 3\/4 in. NPT;\u003c\/li\u003e\n\u003cli\u003ethe relief valve and its discharge line;\u003c\/li\u003e\n\u003cli\u003ethe 240 V electrical connection and a check of the circuit;\u003c\/li\u003e\n\u003cli\u003efilling, purging air, powering up and setting the temperature;\u003c\/li\u003e\n\u003cli\u003ehanding over the warranty documents and our maintenance advice.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eIn a new or extended house\u003c\/h3\u003e\n\u003cp\u003eIn a construction or extension project, the water heater is planned along with everything else: an accessible location near a floor drain, a 240 V circuit planned at the panel, and enough space in front of the elements for future maintenance. The tank weighs 156 lb empty and its exact dimensions are confirmed before ordering; we coordinate delivery and installation with your contractor. Afterwards, a partial flush once a year, a relief valve test and an anode inspection keep the unit in good condition.\u003c\/p\u003e\n\u003ch3\u003eService area\u003c\/h3\u003e\n\u003cp\u003eWe work in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, as well as in Pointe-Claire, L'Île-Bizard, Sainte-Rose, La Prairie, Saint-Amable and everywhere on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e. For a construction or renovation project, our \u003ca href=\"\/en\/pages\/financement-avec-financeit\"\u003efinancing\u003c\/a\u003e lets you spread out the investment.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRequest your free estimate for the Bradford White RE265T10-1NCWW.\u003c\/strong\u003e Send us your plans or a few photos of the mechanical room, and we will prepare a clear written quote.\u003c\/p\u003e","brand":"Bradford White","offers":[{"title":"Default Title","offer_id":67799709286692,"sku":"RE265T10-1NCWW","price":0.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0715\/1694\/6724\/files\/CHAUFFE_EAU_ELECTRIQUE_BRADFORD_WHITE_RE265T10_1NCWW_61_GAL_US_00_MONTREAL_LAVAL_LONGUEUIL_RIVE_SUD_RIVE_NORD.png?v=1793082266"},{"product_id":"chauffe-eau-electrique-bradford-white-re280t6-1ncww-76-gallons-montreal-laval-longueuil-rive-sud-rive-nord","title":"BRADFORD WHITE RE280T6-1NCWW Electric Water Heater (76 gallons) | Montreal, Laval, Longueuil, South Shore \u0026 North Shore","description":"\u003ch2\u003eA large 76 US gallon electric tank for homes that use hot water from morning to night\u003c\/h2\u003e\n\u003cp\u003eIn a home with two or three bathrooms, hot water is not just for morning showers. There is the kids’ bath, the dishwasher, the washing machine, sometimes a large freestanding tub that empties a small tank in minutes. The \u003cstrong\u003eBradford White RE280T6-1NCWW electric water heater\u003c\/strong\u003e is built for that pace. Its tank holds \u003cstrong\u003e76 US gallons (63 imperial gallons, or 288 L)\u003c\/strong\u003e and its \u003cstrong\u003efirst-hour rating\u003c\/strong\u003e reaches \u003cstrong\u003e75 gallons (284 L)\u003c\/strong\u003e, according to the manufacturer’s sheet. AirGreen installs it in \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, on the \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and on the \u003cstrong\u003eNorth Shore\u003c\/strong\u003e, most often to replace a tank that has become too small for the family.\u003c\/p\u003e\n\u003cp\u003eThis is an electric tank water heater in the classic sense: no compressor, no touchscreen, no moving parts. Two 4,500 W immersion elements, a tank lined with Vitraglas with Microban and fittings ready to connect. Its value lies in its volume, its construction and how simple it is to maintain.\u003c\/p\u003e\n\n\u003ch3\u003eWho the RE280T6-1NCWW is for\u003c\/h3\u003e\n\u003cp\u003eThis model is aimed at households that run short of hot water with a standard tank. You find it in multigenerational homes, where grandparents, parents and teenagers share the same supply, in homes with a deep soaking tub or a multi-jet shower, and in families that run several hot-water laundry loads on the same day. A family of five or six taking showers one after another in the morning is a typical example.\u003c\/p\u003e\n\u003cp\u003eOn the other hand, for a couple in a condo or a small house, a tank this size would keep a lot of water hot for no reason. During the assessment, we look at the number of bathrooms, the appliances that run at the same time and your habits before confirming that this format truly suits you.\u003c\/p\u003e\n\n\u003ch3\u003eHow this water heater produces hot water\u003c\/h3\u003e\n\u003cp\u003eCold water from the city supply enters at the bottom of the tank and hot water is drawn from the top. The RE280T6-1NCWW ships \u003cstrong\u003ewired for non-simultaneous operation\u003c\/strong\u003e: only one of its two elements heats at a time. The upper element first restores hot water at the top of the tank, where it is drawn, then the lower element takes over to heat the rest of the volume. This mode limits the current draw to one element at a time, which matches the usual supply of a residential water heater.\u003c\/p\u003e\n\u003cp\u003eBradford White states that simultaneous operation, where both elements heat at the same time, is also available. It must, however, be specified when ordering, and it requires a matching electrical supply. For most homes, the factory wiring is the right choice; we only discuss it with you if your use justifies it.\u003c\/p\u003e\n\n\u003ch3\u003eManufacturer’s data\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003eCapacity:\u003c\/strong\u003e 76 US gallons \/ 63 imperial gallons \/ 288 L\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eFirst-hour rating:\u003c\/strong\u003e 75 gallons (284 L)\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eRecovery:\u003c\/strong\u003e 21 US GPH (18 imperial GPH) at a 90 °F rise, or 79 L\/h at a 50 °C rise, in non-simultaneous 4,500 W \/ 4,500 W operation\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eElements:\u003c\/strong\u003e two 4,500 W screw-in immersion elements, factory-wired non-simultaneous, single phase, 240 V\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eStandby loss:\u003c\/strong\u003e 84 W\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eInner lining:\u003c\/strong\u003e Vitraglas with Microban\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eWater and electrical connections:\u003c\/strong\u003e 3\/4 in (19 mm) NPT, with factory-installed dielectric fittings\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eWeight:\u003c\/strong\u003e 183 lb (83 kg)\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003eListing:\u003c\/strong\u003e UL listed model; approved for manufactured homes, with installation to CAN\/CSA Z240 MH series\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat these figures mean day to day\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003efirst-hour rating\u003c\/strong\u003e shows how much hot water the unit can deliver during one hour of heavy use, starting from a full, hot tank. With 75 gallons, several showers in a row, the dishwasher and a load of laundry can follow one another without the last person ending up under lukewarm water.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRecovery\u003c\/strong\u003e describes what happens once the reserve is drawn down: the heater reheats about 21 US gallons per hour when the water must gain 90 °F. In Quebec, city water arrives colder in winter than in summer. The rise to deliver is therefore larger in January and the real recovery a little slower. That is exactly where a large tank makes the difference: the reserve absorbs the peaks while the elements catch up.\u003c\/p\u003e\n\u003cp\u003eThe \u003cstrong\u003estandby loss\u003c\/strong\u003e of 84 W is the heat the tank loses continuously when no one is using hot water. It is the manufacturer’s measurement; it allows an objective comparison between tanks.\u003c\/p\u003e\n\n\u003ch3\u003eA protected interior and elements that are easy to replace\u003c\/h3\u003e\n\u003cp\u003eThe tank is lined with \u003cstrong\u003eVitraglas with Microban\u003c\/strong\u003e, the lining Bradford White applies to the inner steel to protect it from the water. As in any lined steel tank, a sacrificial anode works alongside the lining; its condition is checked during maintenance, especially when the water is hard.\u003c\/p\u003e\n\u003cp\u003eThe elements are \u003cstrong\u003escrew-in type\u003c\/strong\u003e. The day one of them stops working, it can be replaced on its own after partially draining the tank, without changing the unit. For a water heater that must last many years, this ease of service matters as much as capacity.\u003c\/p\u003e\n\n\u003ch3\u003eVoltage choice and electrical supply\u003c\/h3\u003e\n\u003cp\u003eThe model is factory-wired for \u003cstrong\u003e240 V single phase\u003c\/strong\u003e, the usual supply for a residential water heater in Quebec. Bradford White also offers 120 V, 208 V, 277 V and 480 V versions; the 120 V and 277 V versions can only be wired for single-phase operation. These variants are mainly intended for specific buildings and are ordered in advance.\u003c\/p\u003e\n\u003cp\u003eBefore the installation, we check the breaker, the wire gauge and the condition of the circuit that fed your old tank. AirGreen’s RBQ licence covers electrical work: if a correction is needed, it is part of the same written quote.\u003c\/p\u003e\n\n\u003ch3\u003ePreparing the basement location\u003c\/h3\u003e\n\u003cp\u003eA 76 US gallon tank weighs 183 lb empty and much more once filled. It must sit on a level concrete floor or a solid base, ideally in a drain pan connected to a floor drain. We also check the path down the stairs and through door frames, as well as the free space in front of the element panel for future service. The exact jacket dimensions are confirmed with the order sheet and compared with our on-site measurements.\u003c\/p\u003e\n\u003cp\u003eIf your water entrance has a check valve or a pressure-reducing valve, heated water can no longer expand back toward the city supply. A thermal expansion tank is then recommended; we include it in the quote when that is the case.\u003c\/p\u003e\n\n\u003ch3\u003eManufacturer’s warranty\u003c\/h3\u003e\n\u003cp\u003eThe RE280T6-1NCWW is covered by a \u003cstrong\u003e6-year limited tank warranty\u003c\/strong\u003e and a \u003cstrong\u003e6-year limited parts warranty\u003c\/strong\u003e. The manufacturer’s full terms are given to you with the written quote.\u003c\/p\u003e\n\n\u003ch3\u003eSimple maintenance for a long life\u003c\/h3\u003e\n\u003cp\u003eOne maintenance visit per year is enough in most homes: partial draining to remove sediment from the bottom, a test of the relief valve, a check of the fittings and an inspection of the anode at regular intervals. A few minutes of checking avoids many leaks in the basement.\u003c\/p\u003e\n\n\u003ch2\u003eInstallation of the Bradford White RE280T6-1NCWW by AirGreen in Greater Montreal\u003c\/h2\u003e\n\u003cp\u003eAirGreen is a family business established in Montreal and active in heating, ventilation and air conditioning for more than fifteen years. Our RBQ licence 5645-9605-01 covers ventilation, refrigeration and electrical work. For this water heater, our work includes:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eassessment of the location: access, floor strength, drain, service space in front of the elements;\u003c\/li\u003e\n\u003cli\u003edraining, disconnecting and removing the old tank;\u003c\/li\u003e\n\u003cli\u003econnecting the cold and hot water lines in 3\/4 in, with the required shut-off valves;\u003c\/li\u003e\n\u003cli\u003einstalling the temperature and pressure relief valve and its discharge pipe to the drain;\u003c\/li\u003e\n\u003cli\u003ethe 240 V electrical connection and a check of the circuit;\u003c\/li\u003e\n\u003cli\u003efilling, purging the air and commissioning, with the thermostats set;\u003c\/li\u003e\n\u003cli\u003emaintenance advice: yearly draining, relief valve test, anode follow-up.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eWe serve \u003cstrong\u003eMontreal\u003c\/strong\u003e, \u003cstrong\u003eLaval\u003c\/strong\u003e, \u003cstrong\u003eLongueuil\u003c\/strong\u003e, Brossard, Saint-Lambert, Boucherville, Terrebonne, Blainville, Repentigny and the entire \u003cstrong\u003eSouth Shore\u003c\/strong\u003e and \u003cstrong\u003eNorth Shore\u003c\/strong\u003e. The on-site estimate is free and the quote is written. \u003ca href=\"\/en\/pages\/financement-avec-financeit\"\u003eFinancing\u003c\/a\u003e is available to spread the cost of the replacement.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRequest your free quote for the Bradford White RE280T6-1NCWW.\u003c\/strong\u003e Send us a photo of your current tank and its rating plate: we will confirm the format that suits your home.\u003c\/p\u003e","brand":"Bradford White","offers":[{"title":"Default Title","offer_id":67799714332964,"sku":"RE280T6-1NCWW","price":0.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0715\/1694\/6724\/files\/CHAUFFE_EAU_ELECTRIQUE_BRADFORD_WHITE_RE280T6_1NCWW_76_GAL_US_00_MONTREAL_LAVAL_LONGUEUIL_RIVE_SUD_RIVE_NORD.png?v=1793082266"}],"url":"https:\/\/airgreen.ca\/en\/collections\/chauffe-eau-electriques-residentiels-montreal-laval-longueuil-rive-sud-et-rive-nord.oembed","provider":"AirGreen Climatisation \u0026 Chauffage \/ Air Conditioning \u0026 Heating","version":"1.0","type":"link"}