Installation of a MIDEA EVOX G3 2-ton electric furnace with a central system in Bois-des-Filion

A Compact Central Installation in a Tight Mechanical Room in Bois-des-Filion

In Bois-des-Filion, our AirGreen team completed a particularly technical HVAC installation: integrating a 2-ton MIDEA EVOX G3 electric furnace, configured as a central system with an air handler, into a very cramped mechanical room, with existing ducts, raw foundation walls, and limited access around the unit.

This type of project requires much more than a simple equipment replacement. In a house on the North Shore, where mechanical space is often restricted, every detail matters: clearance around the unit, duct connection, drain management, protection of refrigerant lines, future accessibility for HVAC maintenance, and quality of sealing to prevent air loss.

For this installation, the goal was clear: to modernize the central comfort of the residence while maintaining an efficient, clean, and durable configuration.

A 2-ton MIDEA EVOX G3 Adapted to the Needs of a North Shore Home

The 2-ton MIDEA EVOX G3 is a central solution designed to offer an excellent balance between comfort, energy efficiency, and installation flexibility. In this project in Bois-des-Filion, the 2-ton capacity, or approximately 24,000 BTU, was very well suited to the house's needs, depending on the building's configuration, existing air distribution, and the client's expectations.

Why choose a central system with an air handler?

A central air handler distributes heated or air-conditioned air through the house's ducts. Unlike a wall-mounted air conditioner or a single-zone wall-mounted heat pump, a central system aims for more uniform comfort across multiple rooms.

For this client, the main advantages were:

• better air distribution throughout the house;
• discreet integration, with no visible wall units in main rooms;
• compatibility with an existing duct network;
• an efficient solution for heating and air conditioning;
• a solid foundation for regular preventive maintenance.

At AirGreen, we always assess whether the existing duct network is truly compatible with the new unit. A high-performance machine can yield disappointing results if the ducts are poorly connected, too restrictive, or poorly insulated.

An Installation Space Requiring Precision and Method

The photo of this installation clearly shows the reality on the ground: a narrow mechanical room, with irregular foundation walls, existing metal ducts above the unit, an insulated flexible duct nearby, and limited side access.

In this type of environment, our team must work with great precision. The unit must be positioned to respect the necessary clearances, while maintaining reasonable access to service panels. A common error in central installations is placing the unit too close to a wall or obstacle, which complicates future repairs and increases maintenance costs.

Here, we paid particular attention to:

• the alignment of the unit with the return and supply air;
• the clean connection to existing ducts;
• the insulation of the lines to limit thermal losses;
• the protection of connections;
• the management of space around the unit;
• the stability of the installation in a restricted mechanical environment.

Connection to Existing Ducts: An Essential Step

A central system does not only depend on the quality of the electric furnace or air handler. It also heavily depends on the quality of the distribution network. In Montreal, Laval, Longueuil, on the North Shore and the South Shore, we often see houses where ducts have been modified over the years: additions, repairs, poorly sealed sections, air leaks, dried-out old aluminum tapes, or improvised metal transitions.

In this project, our team took the time to check the critical junctions around the unit. The goal was not only to install the new MIDEA EVOX G3, but to ensure that the air produced was properly delivered to the rooms of the house.

A good connection allows for:

• reducing air loss;
• improving static pressure;
• promoting quieter operation;
• increasing comfort in distant rooms;
• decreasing unnecessary equipment cycles.

The Importance of Insulated and Well-Protected Lines

In the image, we notice the insulated lines running down near the unit, which have been carefully routed in the available space. This step is particularly important for a central system linked to an outdoor heat pump.

A poorly protected or poorly insulated line can lead to efficiency losses, condensation, or even long-term problems if exposed to friction or pressure points. In a compact mechanical room, lines must be carefully positioned to avoid damage during future maintenance.

At AirGreen, we pay particular attention to these kinds of details, as these often invisible elements make the difference between an ordinary installation and a durable HVAC installation.

A Solution Designed for Year-Round Comfort

The 2-ton MIDEA EVOX G3 electric furnace installed in Bois-des-Filion is part of a four-season comfort approach. In summer, the central system air conditions the house with uniform distribution. In winter, the air handler can contribute to central heating depending on the complete system configuration.

This type of installation is particularly appealing to homeowners who want to avoid temperature variations from one room to another. In homes where bedrooms, living rooms, and common areas are served by the same duct network, a central system offers a more consistent experience than a single wall-mounted solution.

Mistakes to Avoid During a Central Installation

A project like this clearly demonstrates why it is important to entrust the installation to a specialized HVAC team. The most common errors we observe during replacements or corrections of installations are as follows:

Choosing the Wrong Capacity

An undersized unit will run too long and won't maintain the desired comfort. An oversized unit can lead to short cycling, poor dehumidification, and premature wear. The 2-ton capacity therefore needed to be validated against the house's actual needs.

Neglecting the Ducts

Installing a new machine on a deficient duct network significantly reduces the benefits of replacement. Transitions, air leaks, and restrictions must be taken seriously.

Forgetting Service Access

A too-tight installation can become problematic during maintenance or repair. Even in a restricted space, access to panels, connections, and internal components must be planned.

Poorly Protecting the Lines

Refrigerant lines and connections must be well insulated, securely fastened, and logically placed. A good installation is not just aesthetic: it must remain reliable over time.

A Clean Installation Despite a Difficult Environment

In this mechanical room in Bois-des-Filion, the conditions were not ideal: raw foundation wall, limited clearance, tight existing ducts, reduced side access. Nevertheless, the final result shows a structured, compact, and functional installation.

Our team had to work around the building's constraints without compromising the quality of the connection. This type of project reflects the reality of many homes on the North Shore, where mechanical space has not always been designed for modern, high-efficiency equipment.

Subsidies and Potential Eligibility

High-performance central systems may sometimes be eligible for financial aid programs, depending on the exact combination of the indoor unit, outdoor unit, AHRI number, energy efficiency, and criteria in effect at the time of installation.

For a MIDEA EVOX G3 central heat pump, eligibility must always be confirmed with the technical documents of the installed model and the current requirements of the applicable program. At AirGreen, we help our clients understand the criteria related to subsidies, especially when the system is installed in Montreal, Laval, Longueuil, on the North Shore or the South Shore.

Our AirGreen Approach to Central Installations

Every central project begins with a practical site analysis. We don't limit ourselves to the machine model. We observe the available space, ducts, electrical panel, drainage, service access, and the client's actual needs.

For this installation in Bois-des-Filion, our approach was simple: install an efficient, clean solution adapted to the building, without forcing a configuration that would complicate future maintenance.

It is this rigor that allows AirGreen to deliver reliable installations in very different contexts: condos in Montreal, single-family homes in Laval, bungalows on the South Shore, multi-zone properties in Longueuil, or central systems on the North Shore.

Practical Advice for Homeowners

Before replacing an electric furnace or a central air handler, it is recommended to check several points:

• the condition of existing ducts;
• the actual capacity required for the house;
• the space available around the unit;
• compatibility with a central heat pump;
• the desired noise level;
• subsidy possibilities;
• future access for HVAC maintenance.

A good choice of equipment is important, but a good installation is even more so. A quality machine installed without precision can lose a significant part of its potential.

A Durable Result for a Bois-des-Filion Home

This installation of a 2-ton MIDEA EVOX G3 electric furnace in Bois-des-Filion perfectly illustrates the type of work we do at AirGreen: a modern central solution, integrated into a complex existing space, with particular attention to connections, insulation, service access, and customer comfort.

For homeowners considering a central HVAC installation in Montreal, Laval, Longueuil, on the North Shore or the South Shore, this project demonstrates the importance of choosing a team capable of adapting to the real constraints of the building while adhering to the technical standards of a professional installation.