Midea heat pump installation in Sainte-Dorothée (Laval): winter performance and clean wall-mounted installation
AirGreen project in Sainte-Dorothée: installation of a Midea heat pump with an outdoor unit on a wall bracket to better manage snow and defrosting, improve stability, reduce vibrations and ensure lasting comfort in summer and winter.
In summer, the outdoor unit rejects the house's heat outside.
Generic illustration of this type of installation, not a survey of this job site. Tap a number.
Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.
The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.
Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.
A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.
The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.
On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.
The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.
When you live in Sainte-Dorothée , you want two things from an HVAC system: consistent comfort and real reliability in winter . At AirGreen , we recently installed a Midea heat pump in a typical Laval residential area: a single-family home, clear lot, snow on the ground, and an outdoor unit installed on a wall bracket securely anchored to the foundation.
The objective: to offer the customer an efficient system for both summer air conditioning and heating during cold periods, while protecting the equipment against ice, snow accumulation and vibrations.
A Midea wall-mounted heat pump designed for the Quebec climate
This project features a Midea wall-mounted heat pump (mini-split/wall unit) . This type of installation is particularly popular in Laval because it offers several advantages:
-
rapid heating and precise control by zone (living room, floor, office, etc.)
-
efficient air conditioning in summer, even during humid heat waves
-
Improved comfort without major ductwork work
-
optimized power consumption, depending on the configuration and usage habits
Selected model (consistent with the Midea range)
When the exact nameplate cannot be read from a photograph, we remain consistent with the product lines actually installed. Here, we present a common and relevant choice for our customers:
-
Midea28 (R-454B, -30 °C) — a platform recognized for its good heating performance and suitability for harsh winters.
In practice, this is the kind of configuration we prefer when a Laval customer wants real winter comfort, not just a “mid-season heat pump”.
What the image reveals: an outdoor installation optimized for winter
The photo clearly shows several elements that indicate an installation designed to last and remain efficient in real-world conditions:
1) Outdoor unit on wall bracket: a real plus in winter
The unit is installed on a steel wall bracket attached to the foundation. In Sainte-Dorothée, this is often the best option because:
-
The unit is elevated and less exposed to snow accumulation.
-
This reduces the risk of blockages caused by ice at the bottom of the machine.
-
This facilitates clearance under the unit during defrosting cycles.
-
Durability is improved by limiting direct contact with soil moisture.
2) Vibration management: stability and sound comfort
In a residential installation, vibrations are an important issue: noise, resonance in the structure, discomfort for the customer (and sometimes for the neighbors).
Here, we see a stable base and a clean assembly. At AirGreen, we systematically add an "anti-vibration" approach:
-
secure fixing to the wall/foundation
-
Positioning that respects clearances
-
Pay attention to contact points (to prevent a simple detail from becoming a recurring noise in the middle of January).
3) Protected refrigeration connections and clean finish
The connections (piping + insulation) and the routing on the right side are clearly visible. A neat installation is as much about aesthetics as it is about functionality.
-
protecting the insulation to maintain its effectiveness
-
minimizing losses and protecting against damage (humidity, shocks, UV)
-
Net result on a house facade (important in a residential area)
4) Positioning against the foundation: logical and effective
The machine is placed near the building, which generally allows:
-
a shorter connection route (better efficiency)
-
a more visually discreet installation
-
an area often more sheltered from the wind, while still maintaining the necessary clearances
Why this choice is particularly relevant in Sainte-Dorothée
In Laval, and more specifically in Sainte-Dorothée, one often encounters:
-
single-family homes with basements (low windows, exposed foundation)
-
areas of terrain where snow accumulates and refreezes
-
rapid temperature variations (thaw, rain, refreeze)
This is exactly the context in which the installation must be designed “winter first” , especially if the customer wants to rely on their heat pump to heat a good part of the cold season.
The technical points that AirGreen prioritizes on this type of project
Even when everything looks simple in photos, our job is to make the installation robust and stable in the long term. In this type of project, we focus on:
Clearances and air circulation
An outdoor unit needs to draw in and expel air properly. We ensure that:
-
respect the clearances around the device
-
avoid areas where snow/ice may block drainage
-
limit the recirculation of cold air during strong winds
Defrost management
In winter, the heat pump defrosts. That's normal. What shouldn't happen:
-
water that falls onto a surface and refreezes into a "block of ice" under the device
-
Poorly anticipated drainage that ultimately impairs function
-
ice buildup that causes the customer to "hit the machine" (and damage it)
With a properly placed wall mount, these risks are greatly reduced.
Electrical protection and reliability
We always aim for a compliant and safe assembly, with components adapted to the climate. A stable and well-protected power supply is the foundation of reliability.
Customer comfort: what we notice after installation
Customer feedback on this type of Midea installation is often very clear:
-
more stable temperature (fewer fluctuations)
-
better perceived comfort than with a supplementary heater alone
-
quiet air conditioning in summer
-
possibility of keeping certain areas more comfortable without heating the whole house to the maximum
And above all: a well-installed, well-raised, properly clear outdoor unit… avoids a host of problems and unnecessary calls in the middle of winter.
Good maintenance practices (Laval winter special)
To keep a heat pump performing well year after year:
-
clear the snow around the outdoor unit after storms
-
Check that no ice is obstructing the drain under the appliance.
-
Clean/maintain the indoor unit filters according to usage
-
Schedule periodic maintenance (especially if the machine is used for heating).
At AirGreen, we always emphasize: a heat pump is not something you "install and forget about ." Minimal maintenance protects performance, comfort... and lifespan.
Conclusion: a well-designed Midea installation, ready for real Quebec conditions
This installation in Sainte-Dorothée (Laval) perfectly illustrates what we aim for at AirGreen: a Midea heat pump installed in a clean, solid and logical way, with a wall bracket that protects the customer's investment against snow, ice and defrost cycles.
If you are looking for a reliable solution to cool the summer and improve your comfort in the winter, a properly sized and installed Midea wall-mounted heat pump makes a real difference — particularly in an environment like Laval, where the seasons really test the equipment.
How it goes, from the first call to the end
The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.
We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
Model, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
Floors and furniture protected, wall plate position marked level, wall opening located.
A single opening, with the slope the drain needs to flow outside.
Set on a stand raised above the snow, with the clearances the manufacturer requires.
Connected, insulated and protected. The opening is then sealed against water, cold air and insects.
A dedicated circuit and an accessible disconnect near the outdoor unit.
Leak test, vacuum, then start-up and a check of heating and cooling.
Remote, modes, filters: we show you the essentials before we leave.
- The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
- The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
- Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
- The wall openingA single opening, with the slope the drain needs to flow outside.
- The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
- Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
- The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
- Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
- The walkthroughRemote, modes, filters: we show you the essentials before we leave.
And at your place?
Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.
Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.
What to do, season by season
Three habits per season for this unit. They take a few minutes and prevent many calls.
- Clean the indoor unit's filters.
- Clear leaves and debris left on the outdoor unit by winter.
- Test cooling before the first hot days.
- Clean the filters more often when the unit runs a lot.
- Keep plants away from the outdoor unit.
- Check that no water drips from the indoor unit.
- Rake the leaves around the outdoor unit.
- Test heating before the first cold days.
- Book periodic maintenance before winter.
- Keep snow away from the stand and the front of the unit.
- Let the unit defrost: it is normal.
- Never hit the ice on the fins; call us if the unit stays iced up.
Which type of equipment for your project?
Pick what looks like your need.
Four mistakes we do not make
Flip each card to see what we do instead.
What people ask us about this kind of work
Does a wall-mounted heat pump heat in winter?
Wall-mounted or multi-zone: how do I choose?
Where does the outdoor unit go?
Are there grants?
Do I need a permit?
How cold can it heat?
How much can I save?
How is the LogisVert assistance calculated?
Is it noisy?
The outdoor unit is covered in ice: is that normal?
Does AirGreen hold the required licences?
Is the estimate free?
No question matches. Write to us: we answer.
Useful pages for what comes next
More jobs to see, near you
By town, by equipment or by region: browse more than 4,700 published projects.
Each dot: a town where AirGreen has published projects. The glowing dot: this job.
Tell us about your house. We come and see it for free.
The on-site estimate is free and the quote follows within 24 hours.
Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).