Job sheet · Project

Installation of a Goodman wall-mounted air conditioner in Nuns' Island

AirGreen installs and optimizes Goodman wall-mounted air conditioners in condominiums on Nuns' Island. Discreet finishing, condensate management, HVAC compliance, and maintenance. Services are available in Montreal, Laval, Longueuil, the North Shore, and the South Shore.

By AirGreen Climatisation & Chauffage Admin7 min read
City
Region
Equipment
Brand
Challenges
Published
–chapters, to open one by one
7 minto read the whole story
–type of installation
2026year published
At a glance

The job on one screen

Installation of a Goodman wall-mounted air conditioner in Nuns' Island
Installation of a Goodman wall-mounted air conditioner in Nuns' Island
The full story

The article, chapter by chapter

Context: a bright condo on Île-des-Sœurs, a need for controlled freshness

At AirGreen , we regularly work in co-ownerships on Nuns' Island to modernize or recommission wall-mounted air conditioners . In this project, the existing Goodman indoor head was positioned high up, above a hallway overlooking the kitchen and dining room. The objective was clear: to guarantee uniform cooling , limit noise pollution, secure condensate drainage and ensure clean integration compatible with co-ownership regulations.

Site reading and construction site preparation

Before any action, we carry out a complete check :

  • Mechanical condition of the wall head (casing wear, flap clearances, filters, turbine bearings).

  • Potential route of refrigeration lines and communication cable , presence of an old drilling, accessibility for maintenance.

  • Condensate drainage solution: search for a possible gravity drain; failing that, selection of a compact, soundproof drainage pump .

  • Electrical compatibility (dedicated circuit breaker, rating, voltage, routing to the outdoor unit).

  • Co-ownership constraints (passage through walls, aesthetics of interior finishing hoods , exterior installation on balcony or facade wall according to regulations).

This preparation avoids surprises, reduces openings to the bare minimum and speeds up the return to service .

Wall-mounted head installation: precision and discretion

The Goodman head is installed high on the wall , a judicious positioning to promote the stratification of fresh air and its natural descent into the living area. We pay particular attention to:

  • The fixing template to ensure firm, vibration-free support.

  • Perfect alignment to avoid unwanted noise and air leaks at the front plenum.

  • The curvature radius of the refrigeration connections to the right of the device, protected by a white cover matching the wall for a discreet appearance.

Result: a sober and silent ensemble, which blends into the interior architecture.

Condensate management: zero drips, zero noise

In co-ownership, gravity draining is not always possible. When required, we select a condensate pump with an integrated tank:

  • Reliable level detection and anti-overflow .

  • Acoustic treatment to limit startup noise.

  • Piping installed with regular slopes and odor traps where required by standards.

This approach avoids any infiltration or marking of the walls , and facilitates annual maintenance.

Wall crossing and refrigerated path

We create a single crossing with the appropriate diameter, with a watertight sheath and vapor barrier . The connections (refrigerator + communication + drain) are grouped in an interior chute with softened angles. Outside, the layout is compact , to limit exposure to the sun and facilitate service access. Each flare is torque checked, the flare nuts are checked, then we proceed to:

  • Deep vacuum (microns) until stabilization.

  • Leak test.

  • Refrigerant charge validated according to the actual length of the lines, in accordance with the manufacturer's specifications.

These steps ensure optimal performance and extend the life of the compressor.

Power supply and compliance

We confirm the presence of a dedicated circuit and appropriate protection (size, circuit breaker, cable type). The connection is carried out properly, with clear markings and compliance with Quebec standards . We favor invisible routes or routes aligned with existing quarter rounds to preserve the aesthetics of the living areas.

Commissioning, balancing and testing

Upon commissioning, our technician:

  1. Calibrates the blowing to avoid direct air currents on the dining table and kitchen island.

  2. Checks flow rate , blowing temperature , turbine-side static pressure and filter integrity .

  3. Set Cooling , Dehumidification and Fan modes with a realistic setpoint for humid days on the river.

  4. Educates customer on minimal HVAC maintenance (cleaning filters every 4–6 weeks in summer, microfiber + warm water, no harsh products).

This sequence ensures quiet and economical operation.

Why this configuration works particularly well in a condo

  • Air diffusion : the high position promotes temperature homogeneity in the open area.

  • Acoustics : the modern, well-fixed wall head limits vibrations on light partitions.

  • Aesthetics : white chutes and clean penetrations preserve the clean lines of the condo.

  • Service : Direct access to the front sump and filters for easy owner maintenance .

Tips for maximizing comfort and energy bills

  • Maintain a constant setpoint (22–24°C in summer) rather than significant variations.

  • Use the dehumidification mode during humid episodes for a feeling of freshness at a higher setting .

  • Program the ventilation to auto speed to let the electronics adapt the flow to the actual thermal load.

  • Clean the filters regularly and schedule annual maintenance by our teams (condensate check, terminal tightening, coil inspection, leak test).

Modernization: When to consider a replacement

Many older Goodman wallheads remain reliable, but replacement may be necessary if:

  • The noise level increases, the shutters become loose, or the card has recurring faults.

  • Seasonal efficiencies are exceeded by current inverter devices with new generation refrigerant .

  • Co-ownership regulations require an aesthetic or acoustic upgrade.

In these cases, we recommend recent wall-mounted heat pumps adapted to Greater Montreal (Montreal, Laval , Longueuil , North Shore , South Shore ) with excellent efficiency and performance in cool weather . Our team offers modern ranges (R-32/R-454B depending on the model) offering four-season comfort , controlled consumption and simplified maintenance .

HVAC Maintenance: What We Do During an Annual Visit

  • Cleaning the filters , turbine and condensate tray.

  • Gentle disinfection of the evaporator coil to limit odors and biofilm.

  • Test the condensate pump (if present), purge and check the pipes.

  • Checking the tightening torques of the connections and visual inspection of tightness.

  • Measurement of inlet/outlet temperatures and adjustment of parameters if necessary.

Annual maintenance means fewer breakdowns, better air quality and more stable bills .

What our customers appreciate about AirGreen

  • Neat and compliant HVAC installations in co-ownership.

  • Administrative support (management regulations, work permits).

  • Realistic deadlines and clear communication from start to finish.

  • Accessible after-sales service , with practical advice and planned maintenance visits.

Need help with your condo on Nuns' Island or elsewhere in Greater Montreal?

Whether you want to optimize your current Goodman wall-mounted air conditioner , repair a recurring problem, or replace it with a newer generation, we will support you from the technical study to commissioning . Our teams cover Montreal , Laval , Longueuil , as well as the North Shore and the South Shore , with slots adapted to condominiums.


Frequently Asked Questions — Condominiums and Wall-Mounted Air Conditioners

Can old refrigeration lines be reused?
We assess the condition, diameter , length and internal cleanliness . If the conditions are not met, we replace the lines to ensure performance and reliability.

Is a condensate pump mandatory in a condo?
Not always. When a gravity drain is impossible or non-compliant, the pump becomes the clean and discreet solution.

How long does the procedure last?
A simple condo modernization is generally carried out within the day , including testing and end-of-construction cleaning.

Is an annual maintenance required?
Yes. HVAC maintenance extends the lifespan, keeps the unit quiet , and reduces consumption.


By choosing AirGreen, you are opting for a local partner who understands the realities of co-ownerships on Île-des-Sœurs and Greater Montreal , and who delivers clean , efficient and long-lasting installations.

Areas served

We operate in Montreal (including Île-des-Sœurs, Verdun, Ville-Marie, Le Sud-Ouest), Laval , Longueuil , as well as on the North Shore and the South Shore for your wall-mounted air conditioners and wall-mounted heat pumps .

Your numbers

The job tools

Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.

Size checkYour baseboards, in BTU/h
–BTU/h of installed electric heat

    Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.

    The steps

    How the job unfolds

    The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.

    Step 1 of 9The on-site estimate

    We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.

    1. The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
    2. The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
    3. Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
    4. The wall openingA single opening, with the slope the drain needs to flow outside.
    5. The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
    6. Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
    7. The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
    8. Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
    9. The walkthroughRemote, modes, filters: we show you the essentials before we leave.
    The tour

    What we check on a job like this one

    Each number is a point we check on site. Switch between summer and winter to watch air and heat move.

    Generic diagram: wall-mounted heat pump, indoor and outdoor units

    In summer, the outdoor unit rejects the house's heat outside.

    Generic illustration of this type of installation, not a survey of this job site. Tap a number.

    1. Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.

    2. The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.

    3. Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.

    4. A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.

    5. The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.

    6. On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.

    7. The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.

    At your place

    Is your home ready?

    Check what applies at your place. A "no" is not a refusal: it is what we sort out during the estimate.

    0 / 6 checked
    Maintenance

    Good habits, once the unit is in place

    Six simple habits that keep the unit going. Your list stays on this device.

    0 / 6 checked
    Through the seasons

    What to do, season by season

    Three habits per season for this unit. They take a few minutes and prevent many calls.

    • Clean the indoor unit's filters.
    • Clear leaves and debris left on the outdoor unit by winter.
    • Test cooling before the first hot days.
    For your project

    The right pages, at the right time

    True or false

    Four statements: true or false?

    It all comes down to details you have just seen.

    1. In heating mode, the outdoor unit can produce water.

    2. You pick the capacity with a simple square-footage rule.

    3. A multi-zone connects several indoor heads to a single condenser.

    4. The disconnect can sit behind the patio furniture.

    Frequently asked questions

    What people ask us about this kind of work

    12 questions
    Does a wall-mounted heat pump heat in winter?
    Yes, it heats and cools. Its capacity drops in very cold weather; the operating range depends on the model and is listed on its spec sheet.
    Wall-mounted or multi-zone: how do I choose?
    One wall head and one condenser outside: the direct solution for a room or an open area. For two to five rooms, a multi-zone puts one head in each room on a single condenser.
    Where does the outdoor unit go?
    Where it stays above the snow, clear and accessible, away from walkways. We decide it with you during the estimate.
    Are there grants?
    Depending on the model and your situation, assistance programs may apply, including Hydro-Québec's LogisVert. AirGreen checks the model number before quoting an amount. See the grants.
    Do I need a permit?
    Rules vary from city to city: location, distances, noise. See permits and by-laws, and we check for your address.
    How cold can it heat?
    It depends on the model. According to Hydro-Québec, newer models work down to a temperature between −15 °C and −25 °C, and some cold-climate models are certified lower. The minimum temperature is on each unit's spec sheet.
    How much can I save?
    Hydro-Québec says a heat pump can be up to three times more efficient than baseboards for heating in the colder months. The result depends on the house, the climate and how it is used.
    How is the LogisVert assistance calculated?
    For ENERGY STAR cold-climate certified heat pumps, Hydro-Québec lists assistance of $120 per 1,000 BTU/h of heating capacity at −8 °C. AirGreen checks the exact model before quoting an amount; only Hydro-Québec confirms the assistance granted. See the grants.
    Is it noisy?
    The sound level depends on the model and is listed in decibels on each unit's spec sheet. Location matters too: when possible, we avoid putting the outdoor unit under a bedroom window.
    The outdoor unit is covered in ice: is that normal?
    Some frost is: the unit runs defrost cycles. Never hit the ice. If the unit stays iced up or stops heating, call us.
    Does AirGreen hold the required licences?
    Yes. AirGreen holds RBQ licence 5645-9605-01, subclasses 15.8 Ventilation, 15.10 Refrigeration and 16 Electricity.
    Is the estimate free?
    Yes. The on-site estimate is free and the quote follows within 24 hours. Book my free estimate.

    Could this job help a neighbour?

    Share
    Similar projects

    More jobs to see, near you

    By town, by equipment or by region: browse more than 4,700 published projects.

    Each dot: a town where AirGreen has published projects. The glowing dot: this job.

    All our projects

    Your project

    An on-site estimate, the right capacity, the right equipment.

    The on-site estimate is free and the quote follows within 24 hours.

    • RBQ licence5645-9605-01 · 15.8, 15.10, 16
    • EstimateOn site, free
    • QuoteWithin 24 hours

    Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).

    Leave a comment