Installation of a GREE FREE MATCH R32 TripleZone Heat Pump – 3 zones – 3 heads in Sainte-Catherine on the South Shore
AirGreen installs a GREE FREE MATCH R32 TripleZone heat pump in Sainte-Catherine: 3 zones, 3 heads, wall-mounted head above a large window, and precise HVAC comfort on the South Shore.
Take a tour of the installation
Each number is a point we check on site. Switch between summer and winter to watch air and heat move.
In summer, the outdoor unit rejects the house's heat outside.
Generic illustration of this type of installation, not a survey of this job site. Tap a number.
Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.
The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.
Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.
A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.
The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.
On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.
The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.
A GREE wall unit precisely installed above a large window in Sainte-Catherine
In Sainte-Catherine, on the South Shore, this installation of a TripleZone GREE FREE MATCH R32 heat pump highlights a detail often underestimated in multi-zone projects: the exact positioning of each indoor unit. In the photo, you can see one of the three GREE wall units installed above a large window, in a bright space where the glazing directly influences heat gains in summer and heat losses in winter.
This type of HVAC installation requires a more detailed analysis than just choosing a device. A room with large glazed openings does not behave like a closed bedroom, a basement, or a corridor. The sun, glazed surface, available height above the window frame, air circulation, and interior aesthetics must all be considered before installing a wall unit. At AirGreen, we pay special attention to these elements because they influence the client's real comfort long after the work is completed.
In this project, the TripleZone GREE FREE MATCH R32 heat pump was chosen to serve three distinct zones with a single outdoor unit. This configuration allows the client to control different sections of the residence separately while reducing outdoor clutter. For a house located in Sainte-Catherine, where summers can be heavy and humid and winters require a reliable supplementary heating solution, the multi-zone system is a very suitable response.
Why install a wall unit above a window?
The location visible in the photo is strategic. Installing a wall unit above a window or patio door can offer excellent results when the available space, wall structure, and airflow direction allow it. In this room, the height above the window provided a clear area to integrate the indoor unit without affecting the layout.
The positioning notably allows:
- air diffusion towards the room rather than directly towards the occupants;
- a discreet integration above the window frame;
- a good distribution of air conditioning in an area exposed to solar gains;
- an efficient use of wall space;
- a clean installation, aligned with existing architectural elements.
The GREE wall-mounted unit, with its sober white finish and discreet digital display, fits well in a contemporary interior. In the photo, the unit shows a set temperature of 26 °C, illustrating a use oriented towards stable comfort rather than excessive cooling. This approach is important: a properly sized and well-placed system does not need to operate aggressively to make a room comfortable.
A TripleZone installation designed for three different realities in the same house
A TripleZone heat pump is not just about installing three identical units. Each zone must be studied according to its use, size, exposure, and relationship with other rooms. In this residence in Sainte-Catherine, the 3 zones – 3 units system was designed to offer better comfort control in several spaces, without imposing a uniform temperature throughout the house.
This is one of the great advantages of the GREE FREE MATCH R32 model: a single outdoor unit can supply multiple indoor units, each controlled independently. For the customer, this means they can adjust the temperature in the main room without necessarily air conditioning an unoccupied bedroom, or heat a space used in the evening without unnecessarily stressing the other zones.
This flexibility is especially useful in homes on the South Shore, where interior layouts vary greatly: open areas, rear extensions, finished basements, upstairs bedrooms, large sun-facing windows, more closed rooms. A multi-zone system allows adapting the HVAC solution to the actual building rather than forcing a single response for the entire house.
The technical challenges behind a well-aligned wall-mounted unit
In a photo, a successful indoor installation looks simple. In reality, several technical decisions must be made before the unit is fixed. For this GREE wall-mounted unit installed in Sainte-Catherine, our technicians had to work with limited space between the ceiling and the top of the window. This area requires great precision.
Respect the necessary clearances
A wall-mounted unit must have enough space around it to ensure good air intake and effective blowing. If it is installed too close to the ceiling or too tight against a molding, performance can be affected. Noise can also increase if the air circulation is poor.
In this project, the unit was placed to maintain adequate clearance while respecting the visual constraints of the room.
Preserving interior aesthetics
The client wanted a clean installation, without an improvised look. The wall unit had to be centered and harmonized with the window, ceiling lines, and surrounding decorative elements. This type of finish is essential in a living room, as the unit remains visible daily.
At AirGreen, we know that a heat pump must not only be efficient. It must also fit properly into the space. A misaligned or too low unit can harm the appearance of a room, even if the system works.
Managing drainage
Each indoor unit produces condensation in cooling mode. The drain must be carefully planned to avoid backflows, insufficient slopes, or moisture marks. In an installation above a window, this step requires special attention, as the available space for passing ducts may be limited.
Reducing noise disturbances
A well-installed wall unit must operate with a comfortable noise level. Positioning, mounting, leveling, and the quality of connections directly influence the perception of noise in the room. For a living area, this detail is essential.
A GREE FREE MATCH R32 solution suitable for homes in Sainte-Catherine, Montreal, Laval, Longueuil, North Shore, and South Shore
The role of R32 refrigerant in modern installations
The GREE FREE MATCH R32 model uses the refrigerant R32, increasingly present in recent HVAC equipment. This choice is part of a transition towards systems designed to offer better thermal performance and improved efficiency. For owners comparing different options for a wall-mounted heat pump or a wall-mounted air conditioner, this point becomes important, especially when they are looking for a durable solution for multiple zones.
The R32 is appreciated for its performance in modern systems and for its ability to support compact and efficient devices. In a TripleZone configuration, however, the quality of the installation remains as important as the choice of equipment. Even a good device will not deliver its full performance if the heads are poorly positioned, if the lines are poorly insulated, or if the commissioning is too quick.
The importance of proper sizing in a 3-unit system
In a residence, three zones do not mean three identical needs. A room with large windows, like the one visible in the photo, may require a different approach than a smaller bedroom or a basement. Natural light, the orientation of the house, ceiling height, and insulation directly influence the thermal load.
Our technicians evaluate several parameters before recommending a configuration:
- the area of each zone;
- the sun exposure;
- the number of windows;
- the ceiling height;
- the level of insulation;
- the daily use of each room;
- the distance between the outdoor unit and the indoor units;
- the possible routing of refrigerant lines and drains.
This analysis helps avoid two common problems: a unit too powerful for a small room or a unit too weak for a very exposed area. In both cases, comfort can be compromised. Proper sizing instead allows for a stable temperature, better modulation, and a more pleasant use of the system.
A customer experience focused on real comfort
In this project in Sainte-Catherine, the client was looking for a solution capable of improving comfort in several zones without multiplying outdoor equipment. The goal was to have a more pleasant home in summer, but also a useful solution during cooler periods, especially in rooms where the existing heating was not always sufficient to provide uniform comfort.
After installation, each indoor unit can be controlled according to the needs of the area it serves. The main room can be cooled on a hot day, while another zone remains at a different temperature. A bedroom can be adjusted in the evening, while a workspace can be treated during the day.
This adjustment freedom is one of the reasons why TripleZone systems are increasingly in demand in Sainte-Catherine, Candiac, Saint-Constant, La Prairie, Brossard, Montreal, Laval, Longueuil, on the North Shore and the South Shore.
Mistakes to avoid in a multi-zone installation
An installation like this requires real expertise. Several mistakes can reduce performance or complicate the daily use of the system.
Placing units only according to available space
Available wall space should never be the only criterion. You must also consider the direction of airflow, air circulation, and where occupants spend the most time.
Neglecting condensation
Poorly planned drainage can cause water problems, especially in cooling mode. Slopes, outlets, and accessibility must be checked rigorously.
Underestimating large windows
Rooms with large windows can heat up quickly in the sun. A wall unit must be positioned and sized taking these heat gains into account.
Installing without considering HVAC maintenance
Filters must remain easy to reach. The unit must be able to be opened and cleaned properly. An installation that is too tight can complicate HVAC maintenance and reduce the system's lifespan.
Comparing price only
In a TripleZone HVAC installation, the quality of the work directly influences reliability. A lower quote may hide compromises on supports, ducts, drains, insulation, or the time spent on commissioning.
The AirGreen approach for a clean and durable installation
AirGreen regularly installs heat pumps, wall air conditioners, and multi-zone systems in Greater Montreal. Our experience with houses, condos, plexes, and properties with architectural constraints allows us to anticipate difficulties before they become problems.
For this installation in Sainte-Catherine, our method focused on three priorities:
- Zone comfort, with an indoor unit placed according to the actual needs of the room.
- Interior finish, to neatly integrate the GREE unit above the windows.
- Long-term reliability, thanks to careful installation, complete commissioning, and clear advice to the client.
This rigor makes a significant difference. A well-installed indoor unit offers better comfort, requires fewer constant adjustments, and naturally integrates into the daily lives of the occupants.
Subsidies and eligibility: check the complete combination
Heat pump subsidy programs can depend on the exact model, the combination of indoor and outdoor units, the installed capacity, and the criteria in effect at the time of the work. For a GREE FREE MATCH R32, it is therefore important to verify the eligibility of the complete configuration, not just the series name.
At AirGreen, we help our clients gather the necessary information when their installation is eligible: invoice, model references, installation details, and useful documents for the application. This assistance is appreciated by homeowners in Montreal, Laval, Longueuil, the North Shore, and the South Shore, as it simplifies a step that can seem technical.
A discreet, efficient result perfectly suited to the room
This installation of a GREE FREE MATCH R32 TripleZone Heat Pump in Sainte-Catherine demonstrates that a successful HVAC project depends as much on the choice of equipment as on the precision of execution. The wall unit visible in the photo is neatly installed above a large window, in a position that respects the room's aesthetics while promoting good air distribution.
With its 3 zones and 3 heads, the system offers the client much more precise control over indoor comfort. Each space can be adjusted according to its use, exposure, and the occupants' preferences. For a property on the South Shore, it is a practical, discreet, and durable solution, especially when several rooms have different needs.
AirGreen continues to support homeowners in Sainte-Catherine, Montreal, Laval, Longueuil, the North Shore, and the South Shore with HVAC installations designed for real comfort, performance, and peace of mind.
The big day, step by step
The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.
We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
Model, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
Floors and furniture protected, wall plate position marked level, wall opening located.
A single opening, with the slope the drain needs to flow outside.
Set on a stand raised above the snow, with the clearances the manufacturer requires.
Connected, insulated and protected. The opening is then sealed against water, cold air and insects.
A dedicated circuit and an accessible disconnect near the outdoor unit.
Leak test, vacuum, then start-up and a check of heating and cooling.
Remote, modes, filters: we show you the essentials before we leave.
- The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
- The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
- Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
- The wall openingA single opening, with the slope the drain needs to flow outside.
- The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
- Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
- The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
- Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
- The walkthroughRemote, modes, filters: we show you the essentials before we leave.
What would it look like at your place?
Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.
Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.
Four mistakes we do not make
Flip each card to see what we do instead.
Your own project, step by step
What to do, season by season
Three habits per season for this unit. They take a few minutes and prevent many calls.
- Clean the indoor unit's filters.
- Clear leaves and debris left on the outdoor unit by winter.
- Test cooling before the first hot days.
- Clean the filters more often when the unit runs a lot.
- Keep plants away from the outdoor unit.
- Check that no water drips from the indoor unit.
- Rake the leaves around the outdoor unit.
- Test heating before the first cold days.
- Book periodic maintenance before winter.
- Keep snow away from the stand and the front of the unit.
- Let the unit defrost: it is normal.
- Never hit the ice on the fins; call us if the unit stays iced up.
Is your home ready?
Check what applies at your place. A "no" is not a refusal: it is what we sort out during the estimate.
Four statements: true or false?
It all comes down to details you have just seen.
1. In heating mode, the outdoor unit can produce water.
During defrost cycles. That water must drain away without forming ice.
2. You pick the capacity with a simple square-footage rule.
Windows, insulation, orientation and how the room is used all count. Capacity is chosen on site.
3. A multi-zone connects several indoor heads to a single condenser.
One head per room, all on the same condenser. Each room keeps its own temperature.
4. The disconnect can sit behind the patio furniture.
It must stay accessible: it is what shuts the unit off for service.
0 / 4 right answers
What people ask us about this kind of work
Does a wall-mounted heat pump heat in winter?
Wall-mounted or multi-zone: how do I choose?
Where does the outdoor unit go?
Are there grants?
Do I need a permit?
How cold can it heat?
How much can I save?
How is the LogisVert assistance calculated?
Is it noisy?
The outdoor unit is covered in ice: is that normal?
Does AirGreen hold the required licences?
Is the estimate free?
No question matches. Write to us: we answer.
More jobs to see, near you
By town, by equipment or by region: browse more than 4,700 published projects.
Each dot: a town where AirGreen has published projects. The glowing dot: this job.
Every house has its constraints. We see them before we install.
The on-site estimate is free and the quote follows within 24 hours.
Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).