Project

Installation of a Gree (R-32 range) wall-mounted heat pump in Rosemont–La Petite-Patrie

AirGreen installs a Gree R-32 wall-mounted heat pump in Rosemont–La Petite-Patrie: raised snow-proof support, hooded finishes, deep vacuum, and complete commissioning. Careful work for four-season comfort in Montreal and the surrounding area.

By AirGreen Climatisation & Chauffage Admin8 min read
Installation of a Gree (R-32 range) wall-mounted heat pump in Rosemont–La Petite-Patrie
Installation of a Gree (R-32 range) wall-mounted heat pump in Rosemont–La Petite-Patrie
Generic diagram: wall-mounted heat pump, indoor and outdoor units

In summer, the outdoor unit rejects the house's heat outside.

Generic illustration of this type of installation, not a survey of this job site. Tap a number.

  1. Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.

  2. The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.

  3. Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.

  4. A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.

  5. The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.

  6. On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.

  7. The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.

A clean, neat project designed for our Montreal winters

At AirGreen , we install efficient and durable wall-mounted heat pumps on a daily basis in Greater Montreal. In Rosemont–La Petite-Patrie, we recently replaced an old air conditioner with a Gree R-32 single-zone unit, chosen for its performance, quiet noise, and compatibility with current low-GWP refrigerant requirements. The work illustrates our approach: rigorous preparation, clean finishes, and an outdoor installation on a raised base to ensure reliable operation even during snow and ice.

Client context and objectives

The owner of a Rosemont duplex wanted:

  • four-season comfort without excessive increases in the electricity bill;

  • quiet operation so as not to disturb the backyard;

  • an outdoor installation away from snow with easy access for maintenance;

  • a clean integration on a side sheet metal cladding and near an external spiral staircase.

After a consultation visit, we recommended a Gree wall-mounted unit from the R-32 range , sized for an open living area and an adjacent bedroom. The final selection took into account Montreal 's real-world needs for supplemental heating and summer cooling, with a priority on seasonal efficiency and longevity .


Outdoor installation: stability, clearances and snow protection

Snow-proof bases and pedestals

We place the outdoor unit on two leveled concrete slabs , receiving a raised aluminum support . This configuration:

  • keeps the casing at the correct height above the ground (clearance for snow accumulation);

  • mechanically decouples the device from the ground using anti-vibration pads;

  • ensures correct drainage of condensates in summer, without splashing.

Clearances and air circulation

The Gree axial fan requires a clear air volume to condense efficiently. We maintain margins at the front and sides for:

  • avoid recycling hot air in summer;

  • limit the risk of frost in auxiliary heating mode;

  • facilitate maintenance maneuvers (access to panels, valves, fittings).

Refrigerant line and power supply management

The cable tray exits laterally, is covered with UV capping and runs with a regular slope towards the wall penetration. This short path limits:

  • pressure losses and weak points;

  • exposure to shocks around the exterior staircase;

  • thermal bridges and direct solar heating.

When the configuration requires it, we integrate an external disconnector according to the code in force to secure interventions. The whole remains sober and discreet , in harmony with the materials present (sheet metal and brick).


AirGreen Methodology: Invisible but Decisive Quality

Flaring, brazing and sealing

We prepare the copper connections in the workshop and then on site, with:

  • clean deburring and controlled flaring;

  • nitrogen brazing when necessary to prevent internal oxidation;

  • dry nitrogen pressure test for several hours to detect any microleaks.

Deep vacuum sealing

Before opening the valves, we perform a vacuum draw down to a level of 500 microns (or better), followed by a lift test . This step guarantees:

  • the absence of humidity and air in the circuit;

  • the stability of R-32 refrigerant and the longevity of the compressor;

  • optimal performance from the start-up.

Performance setting and monitoring

When starting up , we check:

  • the absorbed intensity and the compressor response;

  • the supply/return temperatures on the interior side;

  • stability of defrosting in auxiliary heating mode;

  • the noise level perceived in the backyard and in the home.

We provide the customer with a brief user guide (modes, filters, basic maintenance) and our service contact details for annual follow-up.


Why a Gree in R-32 for Rosemont?

Low GWP refrigerant and modern efficiency

Gree's R-32 range offers reduced global warming potential compared to R-410A generations and allows for higher seasonal efficiencies with inverter compressors. For an apartment or duplex in Rosemont, it is a relevant choice for:

  • air conditioning from May to September;

  • supplementary heating in autumn and spring;

  • controlled noise on the facade or in the courtyard.

Acoustic and aesthetic comfort

The compact housing, optimized fan blades and electronic motor management allow for quiet operation. The raised mounting reduces structural resonances while providing the necessary clearance under the unit.

Simplified maintenance

The exterior cover protects the connections from UV rays and rain. On the interior side, simple and regular filter maintenance maintains performance. AirGreen offers preventative inspections to preserve seasonal performance over the years.


Sizing and good HVAC installation practices

The right BTU for the right room

We size the power (BTU/h) based on the useful surface area , insulation , orientation and internal inputs . Oversizing leads to short cycles and premature wear; undersizing reduces comfort during hot periods . Our technical visit establishes the ideal balance point for your home in Montreal , Laval , Longueuil , North Shore or South Shore .

Controlled lengths, slopes and drillings

Copper connections must remain within the manufacturer's recommended range . We optimize slopes for condensate drainage (gravity where possible) and limit the number of elbows . The drilling is carried out carefully, insulated and sealed to prevent any infiltration.

Winter protection

The raised base protects against snow ridges. We validate the snow removal routes and the absence of obstacles in front of the air intake . If necessary, we add snow guards or adjust the orientation of the unit to limit vortices in gusts.


Grants and eligibility: how to find your way around

Several programs encourage the improvement of energy efficiency . Depending on the exact model and its certified performance , a wall-mounted heat pump may be eligible for assistance (provincial, municipal or utility programs). We verify, on a case-by-case basis, the eligibility of the chosen configuration ( cold test standards, Energy Star , performance thresholds). Our team supports the client in gathering evidence (certification numbers, photos, detailed invoices) and submitting the files correctly.


Result: stable comfort, controlled manufacturing and clean finish

In Rosemont–La Petite-Patrie, the Gree R-32 installed by our teams delivers:

  • a regular temperature in the living area and the adjoining bedroom;

  • a significant drop in humidity in summer;

  • low noise level in the backyard;

  • a clean, perfectly level installation , ready for annual maintenance .

The customer appreciates the simple control and responsiveness of the system during heat peaks . In mid-season, the heating function relieves the electric radiators, which helps to control operating costs .


HVAC Operation and Maintenance Tips by AirGreen

To do

  • Leave the outdoor unit clear (50–100 cm free in front of the grille).

  • Clean the inner head filters every 4 to 8 weeks in summer.

  • Schedule an annual preventive visit : check electrical parameters , vacuum , load , and clean the evaporator and condenser .

To avoid

  • Obstruct the front of the condenser (bins, furniture, bicycles).

  • Allow snow to accumulate under the air intake in winter.

  • Turn off the power supply at the disconnect switch without reason (risk of loss of settings and abnormal cycles).


Why entrust your HVAC installation to AirGreen?

We cover Montreal , Laval , Longueuil , North Shore and South Shore with teams trained in best practices for manufacturers. Our strengths:

  • careful pre-study , correct sizing;

  • careful execution (deep vacuum, pressure tests, hooded finishes);

  • support for subsidies and structured after-sales service ;

  • respect for deadlines and the built environment (surfacing, access, neighborhood).

Are you considering a Gree, Fujitsu, Sharp, or Midea wall-mounted heat pump ? We offer solutions tailored to Montreal homes , transparent pricing , and state-of-the-art installation that's durable, safe, and aesthetically pleasing.


Project Quick Facts (Technical Summary)

  • Market : residential — duplex in Rosemont–La Petite-Patrie .

  • System : Gree single-zone wall-mounted heat pump ( R-32 range).

  • Installation : condenser on raised base fixed on slabs ; UV capping ; short and clear path; compliance with clearances .

  • Procedure : Nitrogen pressure test , deep vacuum , complete commissioning .

  • Objectives : four-season comfort , silence, winter reliability, easy HVAC maintenance .


Ready for a clear and quick quote?

At AirGreen, we evaluate your home, confirm the sizing , document potential eligibility for assistance , and carry out a clean installation that will survive Montreal winters without any surprises. Contact us to schedule a technical visit and obtain a detailed proposal, at the right price, as soon as possible .

The steps

How it goes, from the first call to the end

The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.

Step 1 of 9The on-site estimate

We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.

  1. The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
  2. The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
  3. Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
  4. The wall openingA single opening, with the slope the drain needs to flow outside.
  5. The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
  6. Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
  7. The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
  8. Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
  9. The walkthroughRemote, modes, filters: we show you the essentials before we leave.
Your numbers

And at your place?

Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.

Size checkYour baseboards, in BTU/h
–BTU/h of installed electric heat

    Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.

    Through the seasons

    What to do, season by season

    Three habits per season for this unit. They take a few minutes and prevent many calls.

    • Clean the indoor unit's filters.
    • Clear leaves and debris left on the outdoor unit by winter.
    • Test cooling before the first hot days.
    And at your place?

    Which type of equipment for your project?

    Pick what looks like your need.

    Mistakes avoided

    Four mistakes we do not make

    Flip each card to see what we do instead.

    Frequently asked questions

    What people ask us about this kind of work

    12 questions
    Does a wall-mounted heat pump heat in winter?
    Yes, it heats and cools. Its capacity drops in very cold weather; the operating range depends on the model and is listed on its spec sheet.
    Wall-mounted or multi-zone: how do I choose?
    One wall head and one condenser outside: the direct solution for a room or an open area. For two to five rooms, a multi-zone puts one head in each room on a single condenser.
    Where does the outdoor unit go?
    Where it stays above the snow, clear and accessible, away from walkways. We decide it with you during the estimate.
    Are there grants?
    Depending on the model and your situation, assistance programs may apply, including Hydro-Québec's LogisVert. AirGreen checks the model number before quoting an amount. See the grants.
    Do I need a permit?
    Rules vary from city to city: location, distances, noise. See permits and by-laws, and we check for your address.
    How cold can it heat?
    It depends on the model. According to Hydro-Québec, newer models work down to a temperature between −15 °C and −25 °C, and some cold-climate models are certified lower. The minimum temperature is on each unit's spec sheet.
    How much can I save?
    Hydro-Québec says a heat pump can be up to three times more efficient than baseboards for heating in the colder months. The result depends on the house, the climate and how it is used.
    How is the LogisVert assistance calculated?
    For ENERGY STAR cold-climate certified heat pumps, Hydro-Québec lists assistance of $120 per 1,000 BTU/h of heating capacity at −8 °C. AirGreen checks the exact model before quoting an amount; only Hydro-Québec confirms the assistance granted. See the grants.
    Is it noisy?
    The sound level depends on the model and is listed in decibels on each unit's spec sheet. Location matters too: when possible, we avoid putting the outdoor unit under a bedroom window.
    The outdoor unit is covered in ice: is that normal?
    Some frost is: the unit runs defrost cycles. Never hit the ice. If the unit stays iced up or stops heating, call us.
    Does AirGreen hold the required licences?
    Yes. AirGreen holds RBQ licence 5645-9605-01, subclasses 15.8 Ventilation, 15.10 Refrigeration and 16 Electricity.
    Is the estimate free?
    Yes. The on-site estimate is free and the quote follows within 24 hours. Book my free estimate.
    Going further

    Useful pages for what comes next

    Could this job help a neighbour?

    Share
    Similar projects

    More jobs to see, near you

    By town, by equipment or by region: browse more than 4,700 published projects.

    Each dot: a town where AirGreen has published projects. The glowing dot: this job.

    All our projects

    Your project

    Tell us about your house. We come and see it for free.

    The on-site estimate is free and the quote follows within 24 hours.

    • RBQ licence5645-9605-01 · 15.8, 15.10, 16
    • EstimateOn site, free
    • QuoteWithin 24 hours

    Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).

    Leave a comment