Project

Installation of a Sharp Eco Inverter wall-mounted heat pump in Rosemont–La Petite-Patrie

Installation of a Sharp Eco Inverter wall-mounted heat pump in a Rosemont plex. Raised support, short lines, rigorous commissioning. AirGreen — HVAC experts in Montreal, Laval, Longueuil, North Shore and South Shore .

By AirGreen Climatisation & Chauffage Admin9 min read
Installation of a Sharp Eco Inverter wall-mounted heat pump in Rosemont–La Petite-Patrie
Installation of a Sharp Eco Inverter wall-mounted heat pump in Rosemont–La Petite-Patrie
–chapters in this story
9 minreading time
–type of installation
2026year published
The tour

Take a tour of the installation

Each number is a point we check on site. Switch between summer and winter to watch air and heat move.

Generic diagram: wall-mounted heat pump, indoor and outdoor units

In summer, the outdoor unit rejects the house's heat outside.

Generic illustration of this type of installation, not a survey of this job site. Tap a number.

  1. Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.

  2. The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.

  3. Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.

  4. A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.

  5. The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.

  6. On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.

  7. The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.

The job

Four-season comfort for a Rosemont plex: a neat, quiet HVAC installation designed for Montreal winters

At AirGreen , we are working in a typical plex in Rosemont–La Petite-Patrie . Our client wanted a compact , quiet and economical system, capable of providing summer air conditioning and additional heating in winter . The constraints: a narrow wooden balcony on the 2nd floor, close neighbors, a brick facade and co-ownership rules requiring discreet integration. Our recommendation: a Sharp Eco Inverter wall-mounted heat pump , inverter technology and Plasmacluster Ion filtration , ideal for indoor air and thermal stability in an urban home.

Why Sharp Eco Inverter for Montreal and its metropolis

  • Seasonal efficiency thanks to the inverter compressor which finely adjusts the power according to the load.

  • Air Quality : The Plasmacluster Ion reduces particles and odors in living spaces.

  • Controlled noise level , both indoors and outdoors — crucial for shared balconies and interior courtyards in Montreal .

  • Cold Weather Reliability : Sharp's latest R-32 refrigerant series offers improved low-temperature performance and a reduced carbon footprint compared to older fluids.

Desired result: a reduction in the energy bill , greater comfort in the main rooms and proper integration into the architecture of the Rosemont plexes.


Key steps to a successful HVAC installation on an urban balcony

Load analysis and sizing (BTU)

We start with a thermal diagnosis : living space, orientation, insulation, air infiltration, internal equipment. In this case, the apartment (≈ 70–85 m²) justifies a power of around 12,000 to 15,000 BTU for the living area (living room-kitchen-dining room) and the adjoining bedroom. This range reduces on/off cycles, limits noise and maximizes seasonal efficiency (SEER2/HSPF2 on the recent range).

To remember:

  • Oversizing a heat pump increases noise, creates discomfort (drafts, poorly managed humidity) and reduces efficiency .

  • A good indoor airflow layout is as valuable as the BTU figure.

Choosing an outdoor location: ventilation, vibrations and maintenance

The Sharp outdoor unit sits on a securely mounted galvanized raised stand with anti-vibration pads . This configuration:

  • clears the turbine for optimal air intake and discharge ,

  • limits vibration transmission to the wooden balcony,

  • secures equipment in case of accumulation of blown snow or debris,

  • facilitates HVAC maintenance (coil washing, defrost access).

We scrupulously respect the rear and side clearances required by the manufacturer to avoid the recycling of hot air in summer and guarantee effective defrosting in winter.

Short wall crossing and clean finish

The refrigeration connection is short and direct to the brick facade. We use a continuous insulated sheath , brazed connections , a thorough vacuum and a leak test before charging. On the outside, the lines are sheathed and protected , the wiring is neatly attached, and the condensate slope on the inside is gravity-driven , avoiding the use of a pump in this specific case.

Noise management: respect for the neighborhood and the co-ownership

Montreal plexes require special attention to noise levels :

  • Selecting a low-speed mode for nighttime use.

  • Silent blocks and rigid support to break the vibration transmission to the balcony floor.

  • Orientation of the air outlet so as not to blow towards a neighboring window.
    Our installers also leave usage instructions (speeds, night mode, filter maintenance) to maintain a calm atmosphere.


Technical focus: what makes the AirGreen difference

Meticulous commissioning

  • High vacuum to the micron, stabilization and residual humidity control.

  • Weighing or load adjustment according to actual line length.

  • Electrical checks (section, circuit breaker, differential if required) and communication .

  • Parameter log (temperatures, pressures, intensity) archived for tracking.

Air quality and comfort

The Sharp indoor head, combined with the Plasmacluster , contributes to healthier air . In heating mode, the fine regulation limits thermal shocks : the room remains stable and pleasant, and the relative humidity is better controlled than with a simple convector .

Montreal winter: best practices

  • Maintain clearance around the condenser (balcony clear of leaves and snow).

  • Program smart defrosting using the recommended modes.

  • Avoid blocking the unit with bins, bicycles or seasonal items.

  • Annual cleaning of the coils (exterior/interior) restores efficiency and extends lifespan.


Yields, savings and subsidies: what to expect

Energy efficiency

The recent Sharp R-32 ranges offer competitive SEER2/HSPF2 ratings in the wall-mounted heat pump market. Combined with good sizing and continuous use in variable speed , they offer:

  • a reduction in air conditioning costs in summer,

  • a very economical additional heater in spring and autumn,

  • a reduction in overall consumption compared to on/off devices.

Grants and eligibility (Montreal, Laval, Longueuil, North Shore, South Shore)

Several programs can encourage the energy transition in Quebec. Recent high-performance models , Energy Star and R-32/R-454B , are often eligible under certain conditions (type of housing, low-temperature performance, replacement of an existing system, etc.). At AirGreen, we:

  • let's check the model's admissibility ,

  • we provide support for documents (quotes, proof of installation),

  • suggest, if relevant, improvements (caulking, ventilation) to maximize gains.

Good idea: we will validate your eligibility together whether you are in Montreal , Laval , Longueuil , on the North Shore or the South Shore .


Installation details visible on this Rosemont project

Support, lines and aesthetics

  • Galvanized raised support with anchor plates and anti-vibration pads .

  • Short wall penetration through the brick, insulated and sheathed refrigeration connections.

  • Gravity management of condensates on the interior side (no pump required).

  • Compact path to preserve circulation on the balcony and reduce visual impact.

Deadlines and coordination

  • Technical visit : 45–60 minutes to take measurements, power, routes.

  • Installation : generally half a day to a day for a simple wall-mounted heat pump , including complete testing.

  • Commissioning : measurements and delivery of instructions at the end of the work.


HVAC Operation and Maintenance Tips

To maintain performance

  1. Internal filters : rinse every 1–2 months in summer; in autumn before heating.

  2. Outdoor coils : gentle spring rinse; never force with a concentrated jet.

  3. Clearance : Leave 30–50 cm around the unit; nothing in front of the grille.

  4. Modes : in summer, favor Auto/Cooling with stable low speeds; in the off-season, Heating at moderate settings (20–22°C).

  5. Annual AirGreen visit : inspection, tightening of connections, pressure and leak testing.

Common mistakes to avoid

  • Continuously turn off/on : the inverter is more efficient in modulated continuous operation.

  • Hide the unit behind airtight casing: risk of air recycling and overheating.

  • Neglecting the slope of the condensates : source of odors and humidity.


What if your home requires two zones?

In dual-aspect apartments or houses on the North Shore and South Shore with distant floors and areas, a MultiZone system (Sharp BU/TU series) can better distribute the load. We then size zone by zone (9k/12k/18k/24k BTU) to balance comfort and consumption . When the home is larger (Laval, Longueuil, suburbs), this approach avoids oversizing a single head.


Why entrust your HVAC installation to AirGreen?

  • Specialists in Greater Montreal : we understand the constraints of Montreal plexes, Laval houses, and South Shore/North Shore pavilions.

  • Clean and documented execution : vacuum gauge, functional tests, installation photos, commissioning log .

  • After-sales service : maintenance reminder, parts availability, rapid diagnosis.

  • Grant support : we guide the preparation of files and the required evidence.

Immediate benefit for our Rosemont client: a discreet, quiet, wall-mounted heat pump , ready for summer and efficient in the off-season, with healthier indoor air. All integrated without adding bulk to the facade or encroaching on the balcony.


Next steps

Are you hesitating between 12,000 and 18,000 BTUs ? Are you thinking about a second head for the sleeping area? We will provide a free estimate with precise sizing , and we will provide you with a layout plan . Whether you are in Montreal , Laval , Longueuil , on the North Shore or the South Shore , our team will support you from the study to commissioning .


Express FAQ

Is one head enough for the whole apartment?
In a well-open 4.5, a 12,000–15,000 BTU can cover most of the needs. If the rooms are distant or closed, a second head (or a MultiZone ) optimizes comfort.

Can the Sharp heat up in Montreal in winter?
Yes, for backup and off-season use. In periods of intense cold , it relieves the load on the main heating system and improves targeted comfort.

What about noise for the neighbors?
We work on three axes: sizing , low-speed mode , anti-vibration . The Rosemont plexes require this approach for peaceful cohabitation.

What about subsidies?
Recent, high-performance models with R-32/R-454B are often eligible depending on your situation. We review your application and assist with the process.


Conclusion

This Sharp Eco Inverter installation in Rosemont–La Petite-Patrie illustrates our approach: rigorous sizing , clean installation , controlled silence , and meticulous air quality . It's the ideal balance for Montreal plexes, with real savings and comfort that can be felt all year round.

AirGreen — your HVAC partner in Montreal , Laval , Longueuil , North Shore and South Shore .

The steps

The big day, step by step

The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.

Step 1 of 9The on-site estimate

We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.

  1. The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
  2. The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
  3. Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
  4. The wall openingA single opening, with the slope the drain needs to flow outside.
  5. The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
  6. Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
  7. The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
  8. Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
  9. The walkthroughRemote, modes, filters: we show you the essentials before we leave.
Your numbers

What would it look like at your place?

Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.

Size checkYour baseboards, in BTU/h
–BTU/h of installed electric heat

    Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.

    Mistakes avoided

    Four mistakes we do not make

    Flip each card to see what we do instead.

    Going further

    Your own project, step by step

    Through the seasons

    What to do, season by season

    Three habits per season for this unit. They take a few minutes and prevent many calls.

    • Clean the indoor unit's filters.
    • Clear leaves and debris left on the outdoor unit by winter.
    • Test cooling before the first hot days.
    At your place

    Is your home ready?

    Check what applies at your place. A "no" is not a refusal: it is what we sort out during the estimate.

    0 / 6 checked
    True or false

    Four statements: true or false?

    It all comes down to details you have just seen.

    1. In heating mode, the outdoor unit can produce water.

    2. You pick the capacity with a simple square-footage rule.

    3. A multi-zone connects several indoor heads to a single condenser.

    4. The disconnect can sit behind the patio furniture.

    Frequently asked questions

    What people ask us about this kind of work

    12 questions
    Does a wall-mounted heat pump heat in winter?
    Yes, it heats and cools. Its capacity drops in very cold weather; the operating range depends on the model and is listed on its spec sheet.
    Wall-mounted or multi-zone: how do I choose?
    One wall head and one condenser outside: the direct solution for a room or an open area. For two to five rooms, a multi-zone puts one head in each room on a single condenser.
    Where does the outdoor unit go?
    Where it stays above the snow, clear and accessible, away from walkways. We decide it with you during the estimate.
    Are there grants?
    Depending on the model and your situation, assistance programs may apply, including Hydro-Québec's LogisVert. AirGreen checks the model number before quoting an amount. See the grants.
    Do I need a permit?
    Rules vary from city to city: location, distances, noise. See permits and by-laws, and we check for your address.
    How cold can it heat?
    It depends on the model. According to Hydro-Québec, newer models work down to a temperature between −15 °C and −25 °C, and some cold-climate models are certified lower. The minimum temperature is on each unit's spec sheet.
    How much can I save?
    Hydro-Québec says a heat pump can be up to three times more efficient than baseboards for heating in the colder months. The result depends on the house, the climate and how it is used.
    How is the LogisVert assistance calculated?
    For ENERGY STAR cold-climate certified heat pumps, Hydro-Québec lists assistance of $120 per 1,000 BTU/h of heating capacity at −8 °C. AirGreen checks the exact model before quoting an amount; only Hydro-Québec confirms the assistance granted. See the grants.
    Is it noisy?
    The sound level depends on the model and is listed in decibels on each unit's spec sheet. Location matters too: when possible, we avoid putting the outdoor unit under a bedroom window.
    The outdoor unit is covered in ice: is that normal?
    Some frost is: the unit runs defrost cycles. Never hit the ice. If the unit stays iced up or stops heating, call us.
    Does AirGreen hold the required licences?
    Yes. AirGreen holds RBQ licence 5645-9605-01, subclasses 15.8 Ventilation, 15.10 Refrigeration and 16 Electricity.
    Is the estimate free?
    Yes. The on-site estimate is free and the quote follows within 24 hours. Book my free estimate.

    Could this job help a neighbour?

    Share
    Similar projects

    More jobs to see, near you

    By town, by equipment or by region: browse more than 4,700 published projects.

    Each dot: a town where AirGreen has published projects. The glowing dot: this job.

    All our projects

    Your project

    Every house has its constraints. We see them before we install.

    The on-site estimate is free and the quote follows within 24 hours.

    • RBQ licence5645-9605-01 · 15.8, 15.10, 16
    • EstimateOn site, free
    • QuoteWithin 24 hours

    Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).

    Leave a comment