Project

Installation of a Sharp ZU series wall-mounted heat pump in Mercier–Hochelaga-Maisonneuve

AirGreen installs a Sharp ZU series wall-mounted heat pump in Hochelaga-Maisonneuve: compressor sheltered under a balcony, raised support, discreet capping and an outdoor disconnect switch. Four-season comfort and HVAC maintenance for Greater Montreal.

By AirGreen Climatisation & Chauffage Admin7 min read
Installation of a Sharp ZU series wall-mounted heat pump in Mercier–Hochelaga-Maisonneuve
Installation of a Sharp ZU series wall-mounted heat pump in Mercier–Hochelaga-Maisonneuve
–chapters in this story
7 minreading time
–type of installation
2026year published
The tour

Take a tour of the installation

Each number is a point we check on site. Switch between summer and winter to watch air and heat move.

Generic diagram: wall-mounted heat pump, indoor and outdoor units

In summer, the outdoor unit rejects the house's heat outside.

Generic illustration of this type of installation, not a survey of this job site. Tap a number.

  1. Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.

  2. The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.

  3. Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.

  4. A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.

  5. The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.

  6. On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.

  7. The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.

The job

A protected outdoor location, optimized for the Montreal climate

In Mercier–Hochelaga-Maisonneuve , we are installing a Sharp ZU series wall-mounted heat pump for a Montreal plex apartment. The goal: to provide four-season comfort with a high-performance, quiet, and durable HVAC solution, without compromising the building's aesthetics. The outdoor unit is installed under a balcony slab, sheltered from precipitation and wind-driven snow accumulations.

Choice of location: under the slab, but with controlled clearances

  • Positioned under a concrete canopy , the unit is naturally protected from rain, icicles and snowfall.

  • We respect the clearances around the fan to avoid any recirculation of air during defrosting and to guarantee heat exchange.

  • The orientation of the facade and the presence of a metal staircase impose safety distances to facilitate maintenance and free passage.

Support and anti-vibration: stability = longevity

  • The compressor rests on a treated wooden structure firmly anchored and wedged on pads ; anti-vibration pads absorb micro-transmissions to the slab.

  • This elevation protects against meltwater during defrosting periods and winter puddles, while keeping the service valves accessible.

Refrigeration connections and exterior finishing

  • The dehydrated copper lines are continuously insulated , with careful vapor barrier up to the wall penetrations.

  • A discreet capping groups together refrigerants, communication cable and power supply, for a clean finish and protection against shocks.

Power supply and electrical safety

  • In the immediate vicinity, an external disconnect switch facilitates the isolation of equipment during interventions.

  • The circuit is sized according to the nameplate and protected at the electrical panel by a dedicated circuit breaker.

Condensate and frost management

  • In air conditioning mode, gravity drainage is favored; in winter, the installation under the canopy channels the defrosting water without splashing onto the aisles.

  • The relief of the slab is checked to avoid any water table under the device, which improves cleanliness and limits corrosion.


From planning to start: our AirGreen method

Every building has its own rules. In a typical Montreal apartment complex, the performance of a wall-mounted heat pump depends as much on its sizing as on its installation . Here's how we work to ensure results that meet your expectations.

Responsible sizing and capacity selection

We evaluate:

  • Actual air-conditioned/heated area, ceiling height, partitioning.

  • Solar exposure, air infiltration, insulation quality.

  • Expected noise levels on the stage side.

Typical capacities of the ZU series, suitable for condos and plex floors, are around 9,000, 12,000 or 15,000 BTU . We favor inverter compressor modulation to limit short cycles, stabilize summer humidity and maximize supplemental heating efficiency when temperatures drop.

Key steps of installation

  1. Taking measurements and tracing : layout validated for efficient interior blowing and a short exterior path.

  2. Fixing the interior support : perfect level to ensure the slope of the condensates .

  3. Drilling and wall pass-through : controlled angle, air and water tightness guaranteed.

  4. Installation of connections : compliant flares, torques using the dynamometer .

  5. Vacuum drawing : deep vacuum and sealing before opening the valves.

  6. Electrical connections : earth continuity, disconnector tested.

  7. Commissioning : pressure control, measurement of blown/intake temperature differences , calibration of the flaps for diffusion .

  8. Finishing touches : aligned capping, clean seals, final anti-vibration fixing.

Site challenges and applied solutions

1) Limited height under the balcony. We have validated the front and upper clearances to avoid air recirculation.
2) Circulation in passage areas. The raised platform and the compactness of the support keep the device out of pedestrian areas and simplify snow removal .
3) Noise and neighborhood. Pads and controlled tightening reduce transmission to structures; nighttime silent mode is activated during commissioning.

Everyday performance and comfort

  • Gentle and regular air conditioning even during hot and humid periods; the interior exchanger blows far without unpleasant drafts.

  • Efficient heating in the off-season and as a winter backup; inverter regulation limits temperature fluctuations.

  • Improved air quality thanks to filtration and Sharp's own Plasmacluster technology.

  • Controlled noise : the sheltered location and anti-vibration supports reduce reverberations on the slab.

Yields, refrigerant and compliance

The ZU series relies on a high-efficiency inverter compressor and a refrigerant that meets current standards . The seasonal SEER/HSPF performance, superior to that of older wall-mounted air conditioners, translates into measurable savings . We provide the owner with documentation and a commissioning certificate useful for warranties.

Grants and administrative support

Depending on the exact configuration (certified performance, power, installation conditions), a wall-mounted heat pump may be eligible for available assistance programs. We assist our clients in Montreal, Laval, Longueuil, the North Shore, and the South Shore in verifying criteria, preparing documents, and submitting applications to secure financial assistance whenever possible.

Maintenance and best practices

  • Filters : Clean every 4–8 weeks during heavy summer use.

  • Annual inspection : check condensate flow, deep dust removal, check pressures and condition of connections.

  • Exterior clearances : keep 30–60 cm around the edges free of any objects; clear snow from the facade in winter.

  • Defrost spillway : plan a water path away from the aisles to avoid ice .

  • Usage mode : stable target temperature, moderate Auto ventilation ; in summer, use Dry mode when humidity rises.

Common mistakes to avoid

  • Place the unit at ground level without raising it: risk of immersion by melt water and mechanical shocks.

  • Insufficient clearances under the balcony: reduced performance due to air recirculation.

  • Forget the disconnector or suitable electrical protection.

  • Too long refrigeration path with tight bends: pressure losses and reduced efficiency.

  • Neglecting sealing when drilling: air and humidity infiltration into the wall.

Result for the owner

  • Stabilized comfort in summer and winter in living areas.

  • Energy savings compared to resistive electrical solutions or an old wall-mounted air conditioner.

  • Aesthetic integration : discreet compressor, clean finishes, clear circulation in the courtyard.

  • Peace of mind : warranty documentation, usage advice, and AirGreen after-sales service for maintenance and troubleshooting.

Why choose AirGreen in Greater Montreal

  • Honest advice on the right capacity (9k, 12k, 15k BTU), brand and range for your home.

  • Certified installers who apply Quebec electrical and refrigeration standards.

  • Durable finishes : weatherproof seals, aligned capping, sturdy supports.

  • Complete support : eligibility for subsidies , HVAC maintenance, rapid interventions in Montreal, Laval, Longueuil, North Shore, South Shore .

Quick checklist before your own project

  • Sheltered but ventilated location, with compliant clearances .

  • Raised support and anti-vibration mounts.

  • External disconnect switch and dedicated circuit.

  • Short and isolated route of connections; perfect sealing to the wall.

  • Annual maintenance plan with a qualified partner.

By choosing a methodically installed Sharp ZU series wall-mounted heat pump , you get an efficient, discreet and durable system, perfectly adapted to the climatic and urban realities of Montreal. AirGreen puts its rigor and field experience at the service of reliable installations, designed to last and to offer uncompromising 4-season comfort .

The steps

The big day, step by step

The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.

Step 1 of 9The on-site estimate

We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.

  1. The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
  2. The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
  3. Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
  4. The wall openingA single opening, with the slope the drain needs to flow outside.
  5. The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
  6. Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
  7. The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
  8. Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
  9. The walkthroughRemote, modes, filters: we show you the essentials before we leave.
Your numbers

What would it look like at your place?

Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.

Size checkYour baseboards, in BTU/h
–BTU/h of installed electric heat

    Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.

    Mistakes avoided

    Four mistakes we do not make

    Flip each card to see what we do instead.

    Going further

    Your own project, step by step

    Through the seasons

    What to do, season by season

    Three habits per season for this unit. They take a few minutes and prevent many calls.

    • Clean the indoor unit's filters.
    • Clear leaves and debris left on the outdoor unit by winter.
    • Test cooling before the first hot days.
    At your place

    Is your home ready?

    Check what applies at your place. A "no" is not a refusal: it is what we sort out during the estimate.

    0 / 6 checked
    True or false

    Four statements: true or false?

    It all comes down to details you have just seen.

    1. In heating mode, the outdoor unit can produce water.

    2. You pick the capacity with a simple square-footage rule.

    3. A multi-zone connects several indoor heads to a single condenser.

    4. The disconnect can sit behind the patio furniture.

    Frequently asked questions

    What people ask us about this kind of work

    12 questions
    Does a wall-mounted heat pump heat in winter?
    Yes, it heats and cools. Its capacity drops in very cold weather; the operating range depends on the model and is listed on its spec sheet.
    Wall-mounted or multi-zone: how do I choose?
    One wall head and one condenser outside: the direct solution for a room or an open area. For two to five rooms, a multi-zone puts one head in each room on a single condenser.
    Where does the outdoor unit go?
    Where it stays above the snow, clear and accessible, away from walkways. We decide it with you during the estimate.
    Are there grants?
    Depending on the model and your situation, assistance programs may apply, including Hydro-Québec's LogisVert. AirGreen checks the model number before quoting an amount. See the grants.
    Do I need a permit?
    Rules vary from city to city: location, distances, noise. See permits and by-laws, and we check for your address.
    How cold can it heat?
    It depends on the model. According to Hydro-Québec, newer models work down to a temperature between −15 °C and −25 °C, and some cold-climate models are certified lower. The minimum temperature is on each unit's spec sheet.
    How much can I save?
    Hydro-Québec says a heat pump can be up to three times more efficient than baseboards for heating in the colder months. The result depends on the house, the climate and how it is used.
    How is the LogisVert assistance calculated?
    For ENERGY STAR cold-climate certified heat pumps, Hydro-Québec lists assistance of $120 per 1,000 BTU/h of heating capacity at −8 °C. AirGreen checks the exact model before quoting an amount; only Hydro-Québec confirms the assistance granted. See the grants.
    Is it noisy?
    The sound level depends on the model and is listed in decibels on each unit's spec sheet. Location matters too: when possible, we avoid putting the outdoor unit under a bedroom window.
    The outdoor unit is covered in ice: is that normal?
    Some frost is: the unit runs defrost cycles. Never hit the ice. If the unit stays iced up or stops heating, call us.
    Does AirGreen hold the required licences?
    Yes. AirGreen holds RBQ licence 5645-9605-01, subclasses 15.8 Ventilation, 15.10 Refrigeration and 16 Electricity.
    Is the estimate free?
    Yes. The on-site estimate is free and the quote follows within 24 hours. Book my free estimate.

    Could this job help a neighbour?

    Share
    Similar projects

    More jobs to see, near you

    By town, by equipment or by region: browse more than 4,700 published projects.

    Each dot: a town where AirGreen has published projects. The glowing dot: this job.

    All our projects

    Your project

    Every house has its constraints. We see them before we install.

    The on-site estimate is free and the quote follows within 24 hours.

    • RBQ licence5645-9605-01 · 15.8, 15.10, 16
    • EstimateOn site, free
    • QuoteWithin 24 hours

    Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).

    Leave a comment