Installation of a Sharp wall-mounted heat pump in Outremont
AirGreen installed a Sharp wall-mounted heat pump in Outremont, ensuring year-round comfort and energy savings, with access to subsidies in Montreal and the surrounding area.
Take a tour of the installation
Each number is a point we check on site. Switch between summer and winter to watch air and heat move.
In summer, the outdoor unit rejects the house's heat outside.
Generic illustration of this type of installation, not a survey of this job site. Tap a number.
Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.
The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.
Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.
A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.
The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.
On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.
The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.
Modern comfort in the heart of a historic Montreal neighborhood
In the leafy streets of Outremont , every detail counts when it comes to combining comfort and energy efficiency. One of our recent projects perfectly illustrates how aSharp wall-mounted heat pump is transforming residents' daily lives. The installation took place in a typical home in the area: standard ceilings, clean white walls, and a window overlooking an interior courtyard.
Why a Sharp heat pump for this home?
Choosing a Sharp wall-mounted heat pump is based on three essential criteria:
-
Climate versatility : capable of heating efficiently during Montreal winters and cooling in summer.
-
Compact and stylish : a discreet indoor unit that fits harmoniously above a door.
-
Energy efficiency : eligible for various grant programs, including LogisVert, thanks to its high performance.
Although the exact model was not specified, it is a unit from the Sharp wall-mounted range, renowned for its reliability and stable performance at low temperatures.
The particularities of the installation in Outremont
Every AirGreen project is unique, and this one was no exception. Here are the highlights:
Passage of conduits and wiring
-
The refrigerant and electrical connections were routed through the top of the wall, discreetly running along the partition to reach the exterior.
-
White capping was installed to standardize the route, ensuring an aesthetic finish.
Positioning the indoor unit
-
Placed above the room's entrance door, the wall unit optimizes air circulation.
-
This configuration allows the airflow to be directed towards the depth of the room, maximizing comfort.
Condensate management
-
The drainage was designed using gravity, thus limiting future maintenance.
-
A condensate pump would have been necessary if the outlet had been lower, but the layout of the premises made it unnecessary.
Building context
-
Old window air conditioner visible in another room, gradually replaced by a more modern wall-mounted system.
-
Logical transition: noise reduction, improved energy efficiency, and increased interior space.
Immediate benefits for occupants
The installation of this Sharp heat pump offered several concrete advantages:
-
All-season comfort : constant warmth in winter, coolness in summer.
-
Energy savings : the electricity bill is reduced compared to traditional electric heating.
-
Silence and acoustic comfort : the difference with the old window air conditioner is noticeable, especially in a rest room.
Grants available in Montreal and on the South/North Shore
Thanks to the performance of this heat pump, occupants can benefit from programs such as:
-
Hydro-Québec’s LogisVert , which promotes the installation of high-performance wall-mounted heat pumps.
-
Canadian Greener Homes Grant Program , partially covering purchase and installation costs.
AirGreen expertise at the service of comfort
At AirGreen , each project in Montreal, Laval, Longueuil, on the North Shore or the South Shore is carried out with the same rigor:
-
Preliminary analysis of housing constraints.
-
Choosing the equipment best suited to real needs.
-
Professional, fast and respectful installation of the premises.
-
Administrative support for access to subsidies.
Conclusion: a project representative of AirGreen know-how
This installation of a Sharp wall-mounted heat pump in Outremont demonstrates AirGreen's ability to modernize homes while respecting the unique characteristics of each Montreal neighborhood. Our customers now benefit from optimal thermal comfort and sustainable energy efficiency.
The big day, step by step
The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.
We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
Model, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
Floors and furniture protected, wall plate position marked level, wall opening located.
A single opening, with the slope the drain needs to flow outside.
Set on a stand raised above the snow, with the clearances the manufacturer requires.
Connected, insulated and protected. The opening is then sealed against water, cold air and insects.
A dedicated circuit and an accessible disconnect near the outdoor unit.
Leak test, vacuum, then start-up and a check of heating and cooling.
Remote, modes, filters: we show you the essentials before we leave.
- The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
- The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
- Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
- The wall openingA single opening, with the slope the drain needs to flow outside.
- The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
- Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
- The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
- Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
- The walkthroughRemote, modes, filters: we show you the essentials before we leave.
What would it look like at your place?
Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.
Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.
Four mistakes we do not make
Flip each card to see what we do instead.
Your own project, step by step
What to do, season by season
Three habits per season for this unit. They take a few minutes and prevent many calls.
- Clean the indoor unit's filters.
- Clear leaves and debris left on the outdoor unit by winter.
- Test cooling before the first hot days.
- Clean the filters more often when the unit runs a lot.
- Keep plants away from the outdoor unit.
- Check that no water drips from the indoor unit.
- Rake the leaves around the outdoor unit.
- Test heating before the first cold days.
- Book periodic maintenance before winter.
- Keep snow away from the stand and the front of the unit.
- Let the unit defrost: it is normal.
- Never hit the ice on the fins; call us if the unit stays iced up.
Is your home ready?
Check what applies at your place. A "no" is not a refusal: it is what we sort out during the estimate.
Four statements: true or false?
It all comes down to details you have just seen.
1. In heating mode, the outdoor unit can produce water.
During defrost cycles. That water must drain away without forming ice.
2. You pick the capacity with a simple square-footage rule.
Windows, insulation, orientation and how the room is used all count. Capacity is chosen on site.
3. A multi-zone connects several indoor heads to a single condenser.
One head per room, all on the same condenser. Each room keeps its own temperature.
4. The disconnect can sit behind the patio furniture.
It must stay accessible: it is what shuts the unit off for service.
0 / 4 right answers
What people ask us about this kind of work
Does a wall-mounted heat pump heat in winter?
Wall-mounted or multi-zone: how do I choose?
Where does the outdoor unit go?
Are there grants?
Do I need a permit?
How cold can it heat?
How much can I save?
How is the LogisVert assistance calculated?
Is it noisy?
The outdoor unit is covered in ice: is that normal?
Does AirGreen hold the required licences?
Is the estimate free?
No question matches. Write to us: we answer.
More jobs to see, near you
By town, by equipment or by region: browse more than 4,700 published projects.
Each dot: a town where AirGreen has published projects. The glowing dot: this job.
Every house has its constraints. We see them before we install.
The on-site estimate is free and the quote follows within 24 hours.
Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).