Installation of a Fujitsu AIRSTAGE Orion XLTH+ 15,000 BTU wall-mounted heat pump in Boisbriand on the North Shore
In Boisbriand, AirGreen installs a Fujitsu Orion XLTH+ 15,000 BTU wall-mounted heat pump in a tight space near the ceiling: performance, quiet operation, heating down to -30 °C, and a meticulous finish.
In summer, the outdoor unit rejects the house's heat outside.
Generic illustration of this type of installation, not a survey of this job site. Tap a number.
Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.
The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.
Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.
A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.
The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.
On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.
The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.
A Compact Wall Installation in a Tight Space Near the Ceiling
In Boisbriand, on the North Shore, our AirGreen team installed a Fujitsu AIRSTAGE Orion XLTH+ 15,000 BTU wall-mounted heat pump, a mini-split system designed to provide reliable heating down to -30 °C and efficient air conditioning during Quebec's hot summers.
The project presented a very concrete constraint: the indoor unit had to be installed in a small space, above a window, very close to the textured ceiling. This type of configuration requires great precision, as it is necessary to respect the necessary clearances for air intake, ensure good diffusion into the room, avoid vibrations, and maintain a clean finish despite the limited space available.
The installed model, the Fujitsu Orion XLTH+ 15,000 BTU, was particularly well suited to this Boisbriand residence due to its combination of heating performance, quiet operation, energy efficiency, and potential eligibility for the Hydro-Québec LogisVert grant for eligible projects.
A High-Performance Choice for Boisbriand's Real Climate
Boisbriand experiences the same climatic demands as many cities on the North Shore: harsh winters, frequent thaws, cold winds, humid periods, and increasingly hot summers. For this reason, a simple wall-mounted air conditioning unit is not always sufficient. Owners are now looking for a complete solution: heating, air conditioning, dehumidification, and energy efficiency.
Why the Fujitsu Orion XLTH+ 15,000 BTU was relevant here
The Fujitsu Orion XLTH+ wall-mounted heat pump offers a cooling capacity of 15,000 BTU and heating performance designed for Quebec's low temperatures. This model uses R-32 refrigerant, includes Wi-Fi, boasts high efficiency with a SEER2 of 28.7 and an HSPF2 of 13.0, and remains quiet with an indoor sound pressure level as low as 26 dB(A).
In this Boisbriand installation, these features were of particular importance:
- stable comfort in the living area;
- reduced reliance on electric baseboard heaters;
- discreet operation near an occupied area;
- reliable heating during very cold nights;
- wall-mounted format suitable for installation above a window.
An installation near the ceiling: precision is mandatory
The project image clearly shows the reality of the site: the indoor unit is installed very close to the ceiling, in a place where every inch counts. This kind of installation should never be improvised. A wall unit placed too high, poorly leveled, or too tight against the ceiling can hinder air circulation, complicate maintenance, and increase the risk of noise or uneven performance.
At AirGreen, we paid particular attention to:
- the perfectly straight alignment of the unit;
- the necessary upper clearance for suction;
- the slope of the condensate drain;
- the clean passage of the refrigerant lines;
- the visual finish around the window;
- reducing vibrations transmitted to the wall.
The result is a clean, discreet, and functional HVAC installation, despite a more demanding wall configuration than average.
The challenge of positioning above a window
Installing a wall-mounted heat pump above or near a window requires serious analysis. The presence of framing, a lintel, different materials behind the wall, and sometimes limited space for conduits can complicate the work.
In this case, our team had to choose a position that would allow air to diffuse effectively into the room without being blocked by the ceiling or the window frame. We also made sure that the unit remained accessible for future HVAC maintenance, including filter cleaning, evaporator checking, and drain inspection.
A quiet wall-mounted heat pump for daily comfort
Quietness is an often underestimated criterion when purchasing a mini-split. However, a wall-mounted unit often operates several hours a day, for both heating and air conditioning. The Fujitsu Orion XLTH+ is appreciated for its discretion, making it suitable for living rooms, bedrooms, home offices, and open-plan areas.
In Boisbriand, the location near a living area made this point essential. A unit that was too noisy would quickly disturb the occupants. With this model, thermal comfort is accompanied by smooth, stable, and unobtrusive operation.
Heating down to -30 °C: a major advantage on the North Shore
The North Shore regularly experiences periods where temperatures drop below -20 °C. Choosing a standard heat pump can then become risky if the unit loses too much capacity or constantly requires supplementary heating.
The Fujitsu Orion XLTH+ 15,000 BTU is designed to provide heating down to -30 °C, making it a solid option for homeowners in Boisbriand, Blainville, Sainte-Thérèse, Rosemère, Laval, and the surrounding areas. In a well-configured home, it can significantly reduce the use of electric baseboard heaters while maintaining a more uniform indoor temperature.
R-32 Refrigerant and Energy Efficiency
This model uses R-32, a newer refrigerant than R-410A, recognized for its good thermal performance and reduced environmental impact. For homeowners, this means more current technology, better aligned with new HVAC market standards.
The system's efficiency, combined with Inverter technology, allows the unit to adjust its power according to the actual needs of the room. Instead of operating only on and off, the heat pump modulates its capacity, which improves comfort, reduces temperature variations, and limits unnecessary cycles.
An installation eligible for the LogisVert grant
The Fujitsu Orion XLTH+ 15,000 BTU model is associated with a provincial LogisVert grant that can reach $1,296, depending on applicable eligibility conditions. For many customers in Montreal, Laval, Longueuil, the North Shore, and the South Shore, this financial aid genuinely changes the final cost of the project.
At AirGreen, we support our clients by clearly explaining the important elements: indoor model, outdoor model, AHRI number, proof of installation, final invoice, and Energy Star eligibility when required.
Mistakes to avoid during a wall installation
This project in Boisbriand illustrates several common mistakes we see during replacements or corrections of poorly executed installations:
- choosing a unit too large or too small for the room;
- installing the unit too close to the ceiling without respecting clearance;
- neglecting the slope of the condensate drain;
- using a convenient location for the installer but bad for comfort;
- forgetting future access for maintenance;
- poorly protecting outdoor lines;
- ignoring wall constraints above a window.
A wall-mounted heat pump installation is not limited to simply fixing a unit to the wall. Every detail influences performance, durability, and customer satisfaction.
Why AirGreen for a Fujitsu installation in Boisbriand
Our team regularly installs Fujitsu AIRSTAGE systems, wall-mounted heat pumps, mini-splits, and wall-mounted air conditioners in Greater Montreal, including Boisbriand, Laval, Longueuil, the North Shore, and the South Shore. This experience allows us to anticipate the specific constraints of Quebec homes: old walls, restricted spaces, low ceilings, poorly positioned windows, electrical constraints, and real heating needs in winter.
For this project, our priority was simple: to offer a durable, aesthetic, and high-performing installation, without compromising air circulation or accessibility.
Final result: comfort, performance, and meticulous finish
Once the installation was completed, the Fujitsu Orion XLTH+ 15,000 BTU wall-mounted heat pump integrated cleanly into the wall, above the window, while maintaining a discreet appearance. The client now benefits from a system capable of efficiently heating in winter, quickly cooling in summer, and maintaining constant comfort in the room.
This type of project represents exactly what we seek at AirGreen: an HVAC solution adapted to the building, well-sized, carefully installed, and designed to last.
For homeowners in Boisbriand and on the North Shore who wish to replace an old wall-mounted air conditioner, reduce their heating costs, or improve the comfort of a living area, the Fujitsu AIRSTAGE Orion XLTH+ 15,000 BTU remains a serious, reliable, and perfectly adapted option for the Quebec climate.
How it goes, from the first call to the end
The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.
We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
Model, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
Floors and furniture protected, wall plate position marked level, wall opening located.
A single opening, with the slope the drain needs to flow outside.
Set on a stand raised above the snow, with the clearances the manufacturer requires.
Connected, insulated and protected. The opening is then sealed against water, cold air and insects.
A dedicated circuit and an accessible disconnect near the outdoor unit.
Leak test, vacuum, then start-up and a check of heating and cooling.
Remote, modes, filters: we show you the essentials before we leave.
- The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
- The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
- Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
- The wall openingA single opening, with the slope the drain needs to flow outside.
- The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
- Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
- The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
- Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
- The walkthroughRemote, modes, filters: we show you the essentials before we leave.
And at your place?
Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.
Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.
What to do, season by season
Three habits per season for this unit. They take a few minutes and prevent many calls.
- Clean the indoor unit's filters.
- Clear leaves and debris left on the outdoor unit by winter.
- Test cooling before the first hot days.
- Clean the filters more often when the unit runs a lot.
- Keep plants away from the outdoor unit.
- Check that no water drips from the indoor unit.
- Rake the leaves around the outdoor unit.
- Test heating before the first cold days.
- Book periodic maintenance before winter.
- Keep snow away from the stand and the front of the unit.
- Let the unit defrost: it is normal.
- Never hit the ice on the fins; call us if the unit stays iced up.
Which type of equipment for your project?
Pick what looks like your need.
Four mistakes we do not make
Flip each card to see what we do instead.
What people ask us about this kind of work
Does a wall-mounted heat pump heat in winter?
Wall-mounted or multi-zone: how do I choose?
Where does the outdoor unit go?
Are there grants?
Do I need a permit?
How cold can it heat?
How much can I save?
How is the LogisVert assistance calculated?
Is it noisy?
The outdoor unit is covered in ice: is that normal?
Does AirGreen hold the required licences?
Is the estimate free?
No question matches. Write to us: we answer.
Useful pages for what comes next
More jobs to see, near you
By town, by equipment or by region: browse more than 4,700 published projects.
Each dot: a town where AirGreen has published projects. The glowing dot: this job.
Tell us about your house. We come and see it for free.
The on-site estimate is free and the quote follows within 24 hours.
Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).