Installation of a FUJITSU ORION XLTH 15,000 BTU wall-mounted heat pump in Pont-Viau, Laval
AirGreen installs a FUJITSU ORION XLTH 15,000 BTU wall-mounted heat pump in Pont-Viau, Laval: comfort, efficiency, installation precision, and residential HVAC expertise.
Take a tour of the installation
Each number is a point we check on site. Switch between summer and winter to watch air and heat move.
In summer, the outdoor unit rejects the house's heat outside.
Generic illustration of this type of installation, not a survey of this job site. Tap a number.
Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.
The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.
Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.
A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.
The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.
On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.
The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.
A compact, precise installation perfectly suited for a residential space in Pont-Viau
In Pont-Viau, a well-established residential area of Laval, our AirGreen team recently installed a FUJITSU ORION XLTH 15,000 BTU wall-mounted heat pump, an ideal heating and air conditioning solution for homeowners seeking reliable, discreet, and high-performance comfort throughout the year.
This installation perfectly illustrates a common reality in residential HVAC projects in Laval, Montreal, Longueuil, on the North Shore and the South Shore: it's not enough to choose a good machine. It's crucial to install it in the right place, with the correct clearances, a clean finish, and particular attention to the building's constraints.
In this specific case, the indoor unit had to be installed in a relatively tight space, near the ceiling and close to a light fixture. The photo clearly shows the care taken with alignment, the solidity of the wall mounting, and the integration of the appliance into an already furnished room. The FUJITSU ORION XLTH wall-mounted heat pump was positioned to optimize air distribution while respecting the interior aesthetics of the dwelling.
Why the FUJITSU ORION XLTH 15,000 BTU was a pertinent choice
The FUJITSU ORION XLTH 15,000 BTU model is particularly well-suited for Quebec homes where winter heating is a major challenge. Fujitsu's XLTH range is designed to offer excellent performance in cold climates, making it a very relevant choice for a residence in Pont-Viau, where winters can be demanding.
With a capacity of 15,000 BTU, this wall-mounted heat pump is highly suitable for several residential configurations: open plan, large living room, main floor, spacious condo, or dwelling requiring better temperature control. In an area like Laval, where many properties combine renovated spaces and older structures, sizing the appliance is an essential step.
A machine that is too small would run continuously without achieving the desired comfort. A machine that is too large could cause short cycles, poorly controlled humidity, and premature wear. This is why our team always evaluates:
- the actual area to be covered;
- the building's insulation;
- window orientation;
- ceiling height;
- natural air circulation;
- occupants' heating and cooling habits.
In this project, the 15,000 BTU offered an excellent balance between heating power, summer comfort, and energy efficiency.
A wall installation that required real precision
In the image, we can see that the indoor unit is installed very close to the ceiling. This type of configuration requires rigorous execution. Sufficient space must be provided for air circulation, filter access, future maintenance, and proper opening of the discharge louver.
At AirGreen, we pay particular attention to these details, because a successful HVAC installation is not limited to the machine operating on the day of commissioning. It must also remain practical, clean, and durable after several years of use.
In this project in Pont-Viau, our technicians had to ensure that:
- the wall bracket was securely anchored;
- the indoor unit was perfectly level;
- the routing of the refrigerant lines was well planned;
- condensate drainage respected the necessary slope;
- the appliance remained accessible for HVAC maintenance;
- the interior finish remained clean despite the constraints of the existing wall.
The proximity of the ceiling and the light fixture also required particular attention to avoid creating a conflict between air diffusion, heat produced by the lighting, and the perceived comfort in the room.
The challenge of existing walls in Laval installations
In many houses and condos in Laval, particularly in Pont-Viau, Vimont, Chomedey, or Sainte-Dorothée, interior walls often present surprises: old attachment points, thinner partitions, electrical passages, traces of old installations, or access constraints to the exterior.
In this installation, one can see certain marks on the wall around the unit, typical of an already inhabited residential environment. Our goal was not only to install a new wall-mounted heat pump but to integrate it correctly into a real space, with its constraints, without compromising performance or safety.
This is precisely where the experience of an HVAC contractor specializing in HVAC in Laval becomes important. Poor planning can lead to problems such as:
- a slightly tilted unit that drains poorly;
- unpleasant vibration;
- poor air diffusion;
- difficult access to filters;
- a visually untidy result;
- unnecessary wall repairs after installation.
Our team therefore proceeded methodically, checking the exact location before drilling and validating the final alignment before definitive fixing.
A discreet but highly efficient wall-mounted heat pump
The design of the FUJITSU ORION XLTH indoor unit integrates well into a residential decor. Its white and sober facade allows it to be installed in a bedroom, living room, open corridor, or living area without drawing too much attention.
In this project, the appliance was placed high up to maximize air distribution. This position is strategic: in cooling mode, cool air naturally descends into the room; in heating mode, adjustable vanes allow for better direction of warm air towards the occupied area.
For homeowners in Montreal, Laval, Longueuil, the North Shore, and the South Shore, this aspect is essential. A good heat pump must offer stable comfort, without aggressive drafts and without persistent cold spots.
Concrete benefits for the client
After commissioning, the client benefits from a system capable of meeting two major needs: efficient cooling in summer and economical heating for a large part of winter.
The main advantages of this installation are:
- more stable comfort in the main room;
- a potential reduction in reliance on electric baseboards;
- silent air conditioning during hot periods;
- efficient heating in cold weather;
- better humidity management in summer;
- a compact solution without ductwork;
- added value for the property.
The FUJITSU ORION XLTH 15,000 BTU model also represents a reassuring choice for clients seeking a recognized brand. Fujitsu remains one of the strongest manufacturers in the mini split and wall-mounted heat pump sector in Quebec, particularly due to its reliability, parts availability, and the performance of its systems in cold climates.
What this installation in Pont-Viau teaches homeowners
Don't choose location based solely on appearance
Many clients naturally want to install their wall-mounted air conditioner or heat pump in the most discreet location possible. This is understandable. However, the location must first be chosen based on technical criteria.
An appliance that is too cramped in a corner, too close to an obstacle, or installed in a poorly ventilated area can lose efficiency. In this project, the location near the ceiling was chosen because it allowed good air diffusion while respecting the room's constraints.
Before each installation, AirGreen always analyzes the space to find the best compromise between performance, aesthetics, and ease of maintenance.
Plan for maintenance from the start
A wall-mounted heat pump must be regularly maintained to retain its efficiency. Filters must be cleaned, the indoor unit must remain accessible, and periodic professional maintenance helps prevent many problems.
In this installation in Pont-Viau, we ensured that the appliance could be opened and maintained without major difficulty. This is a seemingly simple detail that makes a big difference after a few seasons of use.
A poorly positioned appliance can make cleaning difficult, discourage maintenance, and reduce the system's lifespan.
Properly size the machine before signing
Choosing a 15,000 BTU should never be automatic. For some dwellings, a 12,000 BTU is sufficient. For others, an 18,000 BTU is more appropriate. In this case, the FUJITSU ORION XLTH 15,000 BTU matched the client's needs and the space configuration well.
At AirGreen, we always prefer to recommend a suitable machine rather than a larger appliance simply because it seems more impressive. In HVAC, the right choice is the one that fits the building, not just the approximate area.
A clean installation also protects performance
System performance depends as much on the quality of the appliance as on the quality of the installation. Refrigerant connections, condensate drainage, sealing of passages, solidity of the mounting, and commissioning are all essential.
An excellent machine poorly installed can become noisy, inefficient, or problematic. Conversely, a well-executed installation allows the system to operate under optimal conditions.
This is why our team attaches as much importance to the invisible steps as to the visible final result on the wall.
Subsidies and eligibility: a point to check before installation
Subsidy programs, particularly those related to efficient heat pumps, can influence the choice of a model. Eligibility generally depends on the exact model, its AHRI number, its energy performance, and the conditions of the program in force at the time of application.
For a heat pump installation in Laval, like this one in Pont-Viau, we always recommend checking eligibility before finalizing the equipment choice. Some Fujitsu models may be eligible according to applicable criteria, but each file must be validated with precision.
AirGreen assists its clients in this step to avoid common errors: choosing an ineligible model, misidentifying equipment, confusing series, or forgetting necessary documents after installation.
Our AirGreen approach to HVAC installations in Laval
This installation of a FUJITSU ORION XLTH 15,000 BTU wall-mounted heat pump in Pont-Viau reflects our way of working: analyzing, planning, installing cleanly, and clearly explaining to the client how to use their new system.
We regularly operate in Laval, but also in Montreal, Longueuil, on the North Shore and the South Shore, for projects involving wall-mounted heat pumps, central systems, multi-zone systems, wall-mounted air conditioners, and complete HVAC solutions.
Every building has its specificities. A condo in Montreal does not have the same constraints as a house in Laval. A residence on the North Shore does not always present the same challenges as a duplex in Longueuil or a bungalow on the South Shore. This is why our recommendations are always adapted to the client's real context.
An installation focused on lasting comfort
The final result is a simple, solid, and efficient installation. The client now has a reliable solution to improve their comfort all year round, with a machine renowned for its performance in cold climates and an installation carried out according to best industry practices.
For AirGreen, this type of project is exactly what defines a good residential HVAC installation: a well-chosen appliance, precise execution, a clean finish, and performance adapted to the needs of the dwelling.
This achievement in Pont-Viau, Laval demonstrates that a wall-mounted heat pump can transform the comfort of a room without major work, provided that the model choice and installation quality are treated with seriousness.
The big day, step by step
The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.
We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
Model, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
Floors and furniture protected, wall plate position marked level, wall opening located.
A single opening, with the slope the drain needs to flow outside.
Set on a stand raised above the snow, with the clearances the manufacturer requires.
Connected, insulated and protected. The opening is then sealed against water, cold air and insects.
A dedicated circuit and an accessible disconnect near the outdoor unit.
Leak test, vacuum, then start-up and a check of heating and cooling.
Remote, modes, filters: we show you the essentials before we leave.
- The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
- The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
- Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
- The wall openingA single opening, with the slope the drain needs to flow outside.
- The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
- Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
- The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
- Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
- The walkthroughRemote, modes, filters: we show you the essentials before we leave.
What would it look like at your place?
Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.
Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.
Four mistakes we do not make
Flip each card to see what we do instead.
Your own project, step by step
What to do, season by season
Three habits per season for this unit. They take a few minutes and prevent many calls.
- Clean the indoor unit's filters.
- Clear leaves and debris left on the outdoor unit by winter.
- Test cooling before the first hot days.
- Clean the filters more often when the unit runs a lot.
- Keep plants away from the outdoor unit.
- Check that no water drips from the indoor unit.
- Rake the leaves around the outdoor unit.
- Test heating before the first cold days.
- Book periodic maintenance before winter.
- Keep snow away from the stand and the front of the unit.
- Let the unit defrost: it is normal.
- Never hit the ice on the fins; call us if the unit stays iced up.
Is your home ready?
Check what applies at your place. A "no" is not a refusal: it is what we sort out during the estimate.
Four statements: true or false?
It all comes down to details you have just seen.
1. In heating mode, the outdoor unit can produce water.
During defrost cycles. That water must drain away without forming ice.
2. You pick the capacity with a simple square-footage rule.
Windows, insulation, orientation and how the room is used all count. Capacity is chosen on site.
3. A multi-zone connects several indoor heads to a single condenser.
One head per room, all on the same condenser. Each room keeps its own temperature.
4. The disconnect can sit behind the patio furniture.
It must stay accessible: it is what shuts the unit off for service.
0 / 4 right answers
What people ask us about this kind of work
Does a wall-mounted heat pump heat in winter?
Wall-mounted or multi-zone: how do I choose?
Where does the outdoor unit go?
Are there grants?
Do I need a permit?
How cold can it heat?
How much can I save?
How is the LogisVert assistance calculated?
Is it noisy?
The outdoor unit is covered in ice: is that normal?
Does AirGreen hold the required licences?
Is the estimate free?
No question matches. Write to us: we answer.
More jobs to see, near you
By town, by equipment or by region: browse more than 4,700 published projects.
Each dot: a town where AirGreen has published projects. The glowing dot: this job.
Every house has its constraints. We see them before we install.
The on-site estimate is free and the quote follows within 24 hours.
Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).