Installation of a GREE AIRY R32 Wall-Mounted Heat Pump in Chomedey, Laval: Discreet Comfort and HVAC Performance in a Low-Ceiling Room
AirGreen installs a GREE AIRY R32 wall-mounted heat pump in Chomedey, Laval: a discreet, efficient mini-split solution designed for four-season comfort.
In summer, the outdoor unit rejects the house's heat outside.
Generic illustration of this type of installation, not a survey of this job site. Tap a number.
Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.
The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.
Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.
A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.
The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.
On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.
The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.
An installation designed for an occupied space, with a clean and efficient finish
In the Chomedey sector of Laval, our AirGreen team installed a GREE AIRY R32 wall-mounted heat pump, a mini split system designed to offer excellent comfort in both air conditioning and heating, while discreetly integrating into an already furnished interior space. The photo of this installation immediately shows a context very representative of many projects we carry out in Greater Montreal: a clear wall, a relatively low suspended ceiling, an area occupied by furniture, and a clear need for uniform comfort without cluttering the space.
This type of configuration requires more than just a simple wall mounting. A successful HVAC installation relies on a precise reading of the room, the available clearance above the unit, the direction of the airflow, the ceiling height, technical access for refrigerant lines, and how occupants actually use the room daily. In Chomedey, we approached this project with particular attention to the balance between performance, visual discretion, and perceived comfort.
The GREE AIRY R32 installed here is a modern wall-mounted heat pump that perfectly meets the needs of owners looking for a reliable, efficient, and aesthetic solution for a living room, a light commercial space, a common room, an office, or a versatile area. Its sleek design allows for natural integration on a pale wall, while its modulation capacity ensures stable temperature without abrupt cycles.
Why the GREE AIRY R32 was a relevant choice for this installation in Chomedey
The GREE AIRY R32 model stands out for its use of R32 refrigerant, a technology increasingly sought after in residential and light commercial HVAC. R32 generally offers better energy efficiency than many older refrigerants, while meeting current expectations for performance and more responsible design.
In this project, the choice of this GREE heat pump was justified for several concrete reasons:
- Discrete wall format, ideal for a space where the interior finish must remain clean.
- Heating and air conditioning function, allowing multi-season use.
- Quiet operation, essential in a room where people may be talking, working, eating, or meeting.
- Good air diffusion, particularly important when a unit is installed near a suspended ceiling.
- Inverter technology, which adjusts power according to actual demand instead of just on-off operation.
- R32 refrigerant, appreciated for its energy performance.
- Sober aesthetic, well suited to light walls and already furnished interior environments.
In Chomedey, as in several sectors of Laval, we often work in buildings where the space available for HVAC equipment is limited. Suspended ceilings, existing partitions, electrical constraints, and aesthetic requirements demand rigorous planning. In this specific case, the wall unit had to be installed high enough to promote good air distribution, while respecting the necessary clearances for maintenance and air circulation.
A clear wall, but a ceiling height to respect
The image shows a unit installed near the ceiling, under acoustic tiles typical of many commercial spaces, offices, or common rooms. This proximity to the ceiling requires careful installation. A unit placed too close to the ceiling may be less effective if air intake is obstructed. Conversely, an installation too low can detract from aesthetics, reduce useful wall space, and compromise optimal air diffusion.
Our team therefore chose a height that allows the GREE AIRY R32 to breathe properly, while maintaining a clean and professional appearance. The result is understated: the unit is well aligned, centered in relation to the available space, and visually light despite its important technical function.
Air diffusion adapted to the actual use of the room
The presence of chairs under the unit indicates that the room is intended to be used regularly by several people. In this type of space, comfort is not limited to achieving a temperature displayed on a remote control. It is necessary to avoid direct drafts on occupants, limit cold or hot spots, and allow for regular diffusion throughout the room.
When installing a wall-mounted air conditioner or wall-mounted heat pump, we pay particular attention to the orientation of the louvers, the distance from seated areas, and the unit's ability to circulate air without causing discomfort. In this project in Laval, the objective was clear: to provide a pleasant temperature, without aggressive airflow, in a room where occupants can remain seated for long periods.
Attention to interior finish
A good installation is not only judged by technical performance. It is also seen in the cleanliness of the final result. On this project, the wall finish had to remain discreet, with no messy visible conduits or unnecessary marks. The white unit blends naturally into the decor, which is particularly important in spaces where the overall appearance of the room matters as much as comfort.
At AirGreen, we place great importance on this dimension. An HVAC installation can be technically correct but visually disappointing if poorly planned. In Chomedey, our intervention resulted in a clean, straight, and consistent installation with the existing environment.
Frequent challenges in this type of installation in Laval
Wall-mounted installations in buildings in Chomedey, Laval, Montreal, Longueuil, the North Shore, and the South Shore often present similar constraints. Even when a room seems simple at first glance, several details must be validated before confirming the final location of the unit.
Among the points we systematically check:
- The structure behind the wall to ensure solid mounting.
- Clearance above the indoor unit.
- Possible routing of refrigerant lines.
- Location of the condensation drain.
- Distance between the indoor and outdoor units.
- Desired sound level in the space.
- Airflow direction according to room use.
- Future access for HVAC maintenance.
- Electrical compliance.
- Visual impact inside and outside the building.
In this project, the presence of the suspended ceiling required particular attention. Acoustic tile ceilings can sometimes offer useful access for certain checks, but they can also conceal obstacles: beams, wiring, existing ducts, structural elements, or passage limitations. This is why our technicians take the time to validate the environment before finalizing drilling, supports, and connections.
GREE AIRY R32: a solution adapted to four-season comfort needs
The GREE AIRY R32 is aimed at customers who want a compact, efficient, and versatile solution. As a wall-mounted heat pump, it can air condition during warm periods and heat when temperatures drop. For many owners in Laval, this versatility is a major argument, especially when seeking to improve the comfort of a specific room without modifying the entire existing heating system.
Inverter technology allows the unit to adjust its power according to the actual needs of the room. Instead of starting at full capacity and then shutting down completely, the unit modulates its operation. This approach improves comfort, reduces temperature variations, and contributes to better energy efficiency.
For readers comparing several heat pump or wall-mounted air conditioner options, this point is essential. Comfort does not only depend on the number of BTUs. It also depends on the unit's ability to maintain a stable temperature, operate quietly, and adapt to changing room conditions.
The importance of proper sizing
A common mistake is to choose a unit based solely on the approximate area of the room. In reality, sizing a mini split must take into account several factors: ceiling height, insulation, solar orientation, number of windows, room usage, number of occupants, internal heat sources, and air circulation.
In a room like the one in this Chomedey installation, the low ceiling and furniture configuration directly influence the diffusion strategy. A unit that is too powerful could cool quickly, but uncomfortably, with short cycles and temperature variations. A unit that is too weak would run too long without achieving the desired comfort. The right choice therefore relies on a serious evaluation before installation.
At AirGreen, we favor a concrete approach: we observe the space, analyze the constraints, and then recommend a solution that corresponds to the actual use of the building. This method avoids unpleasant surprises and improves long-term satisfaction.
An installation that facilitates future maintenance
Another often overlooked aspect is accessibility for HVAC maintenance. A wall-mounted unit must be easy to clean, inspect, and maintain. Filters must remain accessible, the front panel must be able to open correctly, and internal components must be checkable without excessive intervention.
In this installation, the unit was positioned to maintain sufficient accessibility despite its proximity to the ceiling. This detail is important for preserving the performance of the wall-mounted heat pump over the seasons. A well-maintained appliance works better, consumes less, and has a longer lifespan.
We generally recommend that owners clean filters regularly, especially in frequently used rooms. Dust, airborne particles, and continuous use can reduce airflow if maintenance is neglected. For intensively used systems, periodic professional maintenance also checks the drain, coils, connections, and general operation of the appliance.
Subsidies and energy efficiency: a point to check before purchasing
For homeowners in Montreal, Laval, Longueuil, the North Shore, and the South Shore, available subsidy programs can influence the choice of a heat pump. Certain eligible models can reduce the net cost of the project, depending on the criteria in effect at the time of installation.
The GREE AIRY R32, depending on its exact configuration, capacity, and certifications, may be associated with aid or energy efficiency programs. As conditions can vary according to specific models, serial numbers, official lists, and program updates, we help our customers verify relevant information before finalizing their choice.
This point is particularly important: one should never automatically assume that a device is eligible simply because it is efficient. Eligibility must be confirmed with the exact data of the installed model. At AirGreen, we assist our clients in this verification to avoid administrative errors and unrealistic expectations.
What owners should avoid before a wall-mounted installation
Many problems can be avoided with proper preparation. Before installing a wall-mounted heat pump or wall-mounted air conditioner, we advise against hasty decisions about placement. A wall that seems ideal may hide technical constraints. Similarly, a location chosen solely for aesthetic reasons can negatively impact performance.
The most frequent errors are:
- Installing the unit too close to the ceiling.
- Choosing a capacity without a complete evaluation.
- Neglecting condensate drainage.
- Placing the unit facing a seated area without adjusting diffusion.
- Ignoring electrical constraints.
- Underestimating the importance of the outdoor location.
- Forgetting future access for maintenance.
- Comparing only prices without looking at installation quality.
In the HVAC field, the final result depends as much on the appliance as on how it is installed. A good machine poorly installed can become noisy, inefficient, or difficult to maintain. Conversely, a professional installation allows for full utilization of the equipment's capabilities.
AirGreen's expertise in wall-mounted installations in Chomedey and Greater Montreal
AirGreen regularly performs installations of wall-mounted heat pumps, wall-mounted air conditioners, and mini split systems in various environments: single-family homes, condos, small businesses, offices, common rooms, rental housing, technical spaces, and mixed-use premises. This diversity allows us to adapt our method to each project.
In Chomedey, the reality on the ground is often particular. The sector includes residential buildings, condominiums, local businesses, and older buildings where installations must respect existing constraints. Our local experience helps us anticipate challenges: outdoor access, conduit passages, condominium requirements, facade aesthetics, parking for the team, noise, and coordination with occupants.
We apply the same rigor throughout Greater Montreal, whether in Montreal, Laval, Longueuil, on the North Shore or on the South Shore. Each installation is planned to deliver a reliable, clean, and durable result.
A sober, practical, and comfortable final result
The result of this installation in Chomedey perfectly illustrates our approach: a precisely installed GREE AIRY R32, a discreet visual finish, a position adapted to the room, and a comfort solution that respects the actual use of the space. The unit does not dominate the decor. It performs its role efficiently, without cluttering the wall or disturbing the layout.
For occupants, the difference is mainly felt in the stability of comfort. A room that became too hot in the summer or difficult to keep pleasant during transitional periods can now benefit from much more precise control. The heat pump offers a quick, yet modulated, response, which is very suitable for spaces occupied for several hours.
Why choose AirGreen for a GREE AIRY R32 installation
Choosing AirGreen means entrusting your project to a team that understands both technical performance and the realities of buildings in Quebec. We don't just install a device. We analyze the space, recommend the right location, ensure a compliant installation, and think about future maintenance.
Our goal is simple: to deliver a reliable, aesthetic, and customer-daily-life-adapted HVAC installation. In the case of this GREE AIRY R32 wall-mounted heat pump in Chomedey, every detail mattered: installation height, clearance, air diffusion, finish, support stability, and visual integration.
For homeowners considering a similar installation in Laval, Montreal, Longueuil, on the North Shore or South Shore, this project demonstrates that a wall-mounted heat pump can be both powerful, discreet, and well-integrated when installed by an experienced team.
How it goes, from the first call to the end
The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.
We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
Model, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
Floors and furniture protected, wall plate position marked level, wall opening located.
A single opening, with the slope the drain needs to flow outside.
Set on a stand raised above the snow, with the clearances the manufacturer requires.
Connected, insulated and protected. The opening is then sealed against water, cold air and insects.
A dedicated circuit and an accessible disconnect near the outdoor unit.
Leak test, vacuum, then start-up and a check of heating and cooling.
Remote, modes, filters: we show you the essentials before we leave.
- The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
- The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
- Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
- The wall openingA single opening, with the slope the drain needs to flow outside.
- The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
- Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
- The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
- Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
- The walkthroughRemote, modes, filters: we show you the essentials before we leave.
And at your place?
Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.
Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.
What to do, season by season
Three habits per season for this unit. They take a few minutes and prevent many calls.
- Clean the indoor unit's filters.
- Clear leaves and debris left on the outdoor unit by winter.
- Test cooling before the first hot days.
- Clean the filters more often when the unit runs a lot.
- Keep plants away from the outdoor unit.
- Check that no water drips from the indoor unit.
- Rake the leaves around the outdoor unit.
- Test heating before the first cold days.
- Book periodic maintenance before winter.
- Keep snow away from the stand and the front of the unit.
- Let the unit defrost: it is normal.
- Never hit the ice on the fins; call us if the unit stays iced up.
Which type of equipment for your project?
Pick what looks like your need.
Four mistakes we do not make
Flip each card to see what we do instead.
What people ask us about this kind of work
Does a wall-mounted heat pump heat in winter?
Wall-mounted or multi-zone: how do I choose?
Where does the outdoor unit go?
Are there grants?
Do I need a permit?
How cold can it heat?
How much can I save?
How is the LogisVert assistance calculated?
Is it noisy?
The outdoor unit is covered in ice: is that normal?
Does AirGreen hold the required licences?
Is the estimate free?
No question matches. Write to us: we answer.
Useful pages for what comes next
More jobs to see, near you
By town, by equipment or by region: browse more than 4,700 published projects.
Each dot: a town where AirGreen has published projects. The glowing dot: this job.
Tell us about your house. We come and see it for free.
The on-site estimate is free and the quote follows within 24 hours.
Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).