Installation of a GREE SAPPHIRE R32 Wall-Mounted Heat Pump – Mini Split Air Conditioner in Blainville
AirGreen installs a GREE SAPPHIRE R32 wall-mounted heat pump in Blainville: an efficient, discreet mini split suitable for rooms with glass, with local HVAC expertise and LogisVert eligibility to be verified.
Take a tour of the installation
Each number is a point we check on site. Switch between summer and winter to watch air and heat move.
In summer, the outdoor unit rejects the house's heat outside.
Generic illustration of this type of installation, not a survey of this job site. Tap a number.
Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.
The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.
Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.
A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.
The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.
On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.
The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.
A precise wall installation to stabilize the comfort of a highly glazed room
In Blainville, this installation carried out by AirGreen highlights a very common need in homes on the North Shore: effectively controlling the temperature of a bright room exposed to seasonal variations without compromising interior aesthetics. The wall-mounted heat pump GREE SAPPHIRE R32 was installed above a large glazed opening, in a space where solar gains, heat loss near the windows, and air circulation had to be analyzed precisely.
In the project photo, you can see a discreet white indoor unit, well aligned and positioned high above the window. This setup requires special attention: the unit must remain accessible for HVAC maintenance, maintain sufficient clearance for air intake, blow air unobstructed into the room, and properly integrate with curtain rods, window frames, and existing decorative elements.
At AirGreen, we approached this project as a precise HVAC installation, not just a simple wall mount. In such a glazed room, the positioning of the heat pump directly affects the perceived comfort. Too low, the unit could interfere with the layout. Too close to the ceiling, it could hinder air return. Too offset, it would create uneven air distribution. The final result offers a clean, stable, and functional integration, suited to the daily life of a residence in Blainville.
Why the choice of the GREE SAPPHIRE R32 was relevant for this home
The GREE SAPPHIRE R32 model stands out for its high efficiency, quiet operation, and use of the refrigerant R32, an increasingly popular choice for modern wall-mounted heat pump installations. For this installation, the 18,000 BTU version is particularly suitable for an open room or a well-exposed main area when the load calculation confirms that this capacity fits the space.
This model notably offers a cooling capacity of 18,000 BTU, ENERGY STAR certification, ENERGY STAR cold climate certification, included Wi-Fi, a SEER2 efficiency of 27.5, an EER2 of 14.3, a heating capacity rated down to -30 °C, and an indoor sound pressure level of 35 / 49 dB(A) depending on the operating mode. The technical sheet also indicates a power supply of 220 V, an MCA of 20 A, an MOP of 25 A, piping of 1/4 – 5/8 in, and a low-noise outdoor unit at 59 dB(A).
For a homeowner in Blainville, these technical details have concrete importance. A wall-mounted heat pump used as the main comfort solution must be able to meet cooling needs during hot periods but also provide efficient heating during the cold days of fall, spring, and a significant part of the Quebec winter. GREE’s inverter technology allows adjusting the operating speed rather than running only in abrupt cycles, contributing to more stable comfort and better-controlled consumption.
The manufacturer also presents the Sapphire series as a compact, quiet wall solution, equipped with Wi-Fi, intelligent defrost, self-diagnosis, and precise airflow control. These features are especially useful in a living room where the unit often runs for several hours, sometimes with occupants who want to avoid direct drafts or constant noise.
A major constraint: installing above a large window
The central point of this project in Blainville was the location. The unit had to be installed above a large glazed surface, near the ceiling, while respecting good installation practices. This area is often very effective for a heat pump: treated air can be projected into the room, while the unit remains discreet and takes no floor space. However, this type of installation leaves little room for error.
Our technicians paid special attention to four elements:
- The upper clearance, to allow good air intake.
- Alignment with window frames, to achieve a visually clean finish.
- The airflow trajectory, to prevent air from being blocked by the rod or curtains.
- Drainage management, to ensure reliable condensate evacuation.
In this type of configuration, a rushed installation can lead to discomforts: vibration noise, poorly controlled drainage, uneven air distribution, or difficult filter access. At AirGreen, we plan these details before the final mounting. The unit’s level, anchoring strength, refrigerant line routing, and opening protection are validated step by step.
A clean installation, adapted to interior aesthetics
One of the client’s goals was to preserve the bright and orderly look of the room. The indoor unit GREE SAPPHIRE R32 has a sleek design that fits well with light walls and modern windows. The rounded front and discreet display avoid the heavy visual effect that some units can produce when installed in a main room.
Installing above the window also keeps the side walls free for furniture, decorations, or room layout. In many homes in Blainville, Laval, Montreal, Longueuil, the North Shore, and the South Shore, we observe the same priority: clients want a high-performance system, but they also want the equipment to respect their living space.
This project clearly illustrates our approach: installing a wall air conditioner or a wall-mounted heat pump is not just about choosing an available wall. You must understand how occupants live in the room, where the light enters, how air circulates, where curtains fall, and how work can be done without damaging existing surfaces.
Commissioning: the checks that make the difference
After installing the indoor unit and connecting it to the outdoor system, commissioning is an essential step. Our technicians perform the necessary checks to confirm that the installation works correctly from the start.
This includes notably:
- Validating the electrical supply and required protections.
- Checking the tightness of refrigerant connections.
- Vacuuming the lines before startup.
- Verifying drainage.
- Testing cooling and heating functions.
- Explaining the main functions to the client, including Wi-Fi, ventilation modes, heating mode, cooling mode, and filter maintenance.
For a model like the GREE SAPPHIRE R32, these checks are important to preserve energy efficiency and system durability. A highly efficient unit will not deliver full performance if installation, connection, or operating parameters are neglected.
LogisVert subsidy and energy eligibility
The 18,000 BTU version of the GREE SAPPHIRE R32 listed on the AirGreen sheet is associated with a provincial LogisVert aid of $1,860, with a note of an update as of November 26, 2025. This information must always be validated according to the criteria in effect at the time of purchase and installation, as programs may change.
Hydro-Québec specifies that clients must verify the eligibility of the chosen unit before purchase and keep the required documents for the application. The program also includes deadlines and submission conditions, notably the need to submit the application within applicable deadlines after installation.
At AirGreen, we regularly assist clients with this step. We provide the necessary information about the installed equipment to facilitate the application, including the model, required numbers, detailed invoice, and useful technical information. For homeowners in Montreal, Laval, Longueuil, North Shore, and South Shore, this aid can strongly influence the final choice of a heat pump.
What this installation in Blainville teaches homeowners
Do not choose the location solely for visual reasons
A unit installed in the wrong place can create discomfort even if it is an excellent model. In this project, the unit was placed to optimize air distribution in the room while respecting constraints imposed by the window, ceiling, and decorative elements. The right location helps avoid cold spots, short cycles, and the unpleasant sensation of direct air.
Do not neglect capacity calculation
The BTU capacity should never be chosen at random. A unit that is too small will run too long without reaching the desired comfort. A unit that is too large can reduce cooling comfort, create short cycles, and harm dehumidification. For this installation, the analysis of the room, windows, and actual use of the space guided the choice of the GREE SAPPHIRE R32.
Pay attention to windows and sunlight
Large windows are pleasant but directly influence cooling and heating needs. In summer, they can quickly raise indoor temperature. In winter, they can create a cold wall sensation. A successful HVAC installation must take this reality into account, especially in a city like Blainville where seasonal variations are significant.
Plan maintenance from the installation stage
A wall-mounted heat pump must remain accessible. Filters must be easily removable, the front panel must open without constraint, and the unit must be inspectable during HVAC maintenance. In this project, the installation height was designed to balance discretion, performance, and accessibility.
Why call on AirGreen for an HVAC installation in Blainville
AirGreen regularly works in Blainville, on the North Shore, in Laval, in Montreal, in Longueuil, and on the South Shore for installations of wall-mounted heat pumps, wall air conditioners, and mini split systems. Our strength lies in combining solid technical expertise with a real understanding of Quebec homes: window constraints, electrical requirements, variable insulation, condominium regulations, comfort needs across seasons, and eligibility for aid programs.
In this project, the client received a clean, discreet installation adapted to the room. The choice of the GREE SAPPHIRE R32 provides an efficient, quiet unit compatible with modern remote control expectations and designed to meet local climate conditions. The result is a durable comfort solution, well integrated and ready to support the home for many years.
Our professional recommendation
For a Blainville home with a bright room, a large glazed surface, and a need for stable comfort, the GREE SAPPHIRE R32 represents a very serious option when capacity is properly selected. Its efficiency, quiet operation, R32 refrigerant, integrated Wi-Fi, and potential eligibility for financial aid make it a relevant choice for homeowners who want to improve their comfort without weighing down the appearance of their interior space.
This installation demonstrates that a good result depends as much on the choice of the unit as on the quality of the installation. At AirGreen, we give equal importance to sizing, location, finishing, commissioning, and the advice given to the client. This approach transforms a simple wall air conditioner installation into a complete HVAC comfort solution.
The big day, step by step
The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.
We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
Model, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
Floors and furniture protected, wall plate position marked level, wall opening located.
A single opening, with the slope the drain needs to flow outside.
Set on a stand raised above the snow, with the clearances the manufacturer requires.
Connected, insulated and protected. The opening is then sealed against water, cold air and insects.
A dedicated circuit and an accessible disconnect near the outdoor unit.
Leak test, vacuum, then start-up and a check of heating and cooling.
Remote, modes, filters: we show you the essentials before we leave.
- The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
- The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
- Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
- The wall openingA single opening, with the slope the drain needs to flow outside.
- The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
- Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
- The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
- Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
- The walkthroughRemote, modes, filters: we show you the essentials before we leave.
What would it look like at your place?
Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.
Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.
Four mistakes we do not make
Flip each card to see what we do instead.
Your own project, step by step
What to do, season by season
Three habits per season for this unit. They take a few minutes and prevent many calls.
- Clean the indoor unit's filters.
- Clear leaves and debris left on the outdoor unit by winter.
- Test cooling before the first hot days.
- Clean the filters more often when the unit runs a lot.
- Keep plants away from the outdoor unit.
- Check that no water drips from the indoor unit.
- Rake the leaves around the outdoor unit.
- Test heating before the first cold days.
- Book periodic maintenance before winter.
- Keep snow away from the stand and the front of the unit.
- Let the unit defrost: it is normal.
- Never hit the ice on the fins; call us if the unit stays iced up.
Is your home ready?
Check what applies at your place. A "no" is not a refusal: it is what we sort out during the estimate.
Four statements: true or false?
It all comes down to details you have just seen.
1. In heating mode, the outdoor unit can produce water.
During defrost cycles. That water must drain away without forming ice.
2. You pick the capacity with a simple square-footage rule.
Windows, insulation, orientation and how the room is used all count. Capacity is chosen on site.
3. A multi-zone connects several indoor heads to a single condenser.
One head per room, all on the same condenser. Each room keeps its own temperature.
4. The disconnect can sit behind the patio furniture.
It must stay accessible: it is what shuts the unit off for service.
0 / 4 right answers
What people ask us about this kind of work
Does a wall-mounted heat pump heat in winter?
Wall-mounted or multi-zone: how do I choose?
Where does the outdoor unit go?
Are there grants?
Do I need a permit?
How cold can it heat?
How much can I save?
How is the LogisVert assistance calculated?
Is it noisy?
The outdoor unit is covered in ice: is that normal?
Does AirGreen hold the required licences?
Is the estimate free?
No question matches. Write to us: we answer.
More jobs to see, near you
By town, by equipment or by region: browse more than 4,700 published projects.
Each dot: a town where AirGreen has published projects. The glowing dot: this job.
Every house has its constraints. We see them before we install.
The on-site estimate is free and the quote follows within 24 hours.
Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).