Installation of a Sharp wall-mounted heat pump in Southwest Montreal
On a rooftop in Southwest Montreal, AirGreen installed a Sharp ECO Inverter wall-mounted heat pump with Plasmacluster technology, providing economical heating, efficient air conditioning and healthier air for an urban condo, perfectly suited to Quebec winters.

Take a tour of the installation
Each number is a point we check on site. Switch between summer and winter to watch air and heat move.
In summer, the outdoor unit rejects the house's heat outside.
Generic illustration of this type of installation, not a survey of this job site. Tap a number.
Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.
The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.
Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.
A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.
The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.
On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.
The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.
On the flat roof of a residential building in Southwest Montreal, we recently replaced an old air conditioning system with a Sharp ECO Inverter wall-mounted heat pump with Plasmacluster technology . This solution was perfectly suited to the realities of Montreal condominiums and apartments: limited space, noise restrictions, roof access, and of course, our harsh winters.
Context: an urban building, comfort in need of modernization
The building is typical of the Southwest (Griffintown / Saint-Henri) : brick structure, several dwellings, mechanical equipment grouped on the roof and high urban density.
The client wanted:
-
Replacing an older, less efficient system;
-
Improve comfort in both summer and winter ;
-
Reduce your energy consumption;
-
Limit the noise for the neighbors, both inside and on the roof.
The chosen solution: a Sharp ECO Inverter wall-mounted heat pump , connected to one or more indoor wall-mounted heads, ideal for apartments or condos where it is not possible to install a central ducted system.
Choosing the Sharp ECO Inverter wall-mounted heat pump
Inverter technology for stable comfort
The Sharp ECO Inverter range continuously adjusts the compressor speed. Specifically:
-
The heat pump keeps starting and stopping;
-
The indoor temperature remains stable, without large fluctuations;
-
Electricity consumption is reduced compared to a traditional "on/off" device.
This is particularly interesting in Montreal, where the inter-seasons (spring, autumn) represent a good part of the year: the heat pump then operates at low power , maintaining constant comfort with a minimum of energy.
Plasmacluster: healthier indoor air
The Ion Plasmacluster logo clearly visible on the outdoor unit recalls one of Sharp's technological signatures: an air purification system integrated into compatible indoor units.
For the customer, this translates to:
-
A reduction in odors and certain suspended particles;
-
More pleasant indoor air, which is appreciated in an urban apartment surrounded by traffic and pollution;
-
A heating/air conditioning system that not only manages the temperature, but also contributes to overall well-being .
Details of the outdoor installation on a flat roof
The photo clearly shows several key elements of our work:
1. Sturdy raised stand
The Sharp heat pump is installed on a metal base, which is itself fixed to wooden crossbeams resting on structural bases. This assembly serves several purposes:
-
Protect the unit against the accumulation of snow and ice;
-
Ensure excellent water drainage on the roof membrane;
-
Limit the transmission of vibrations to the building structure.
We use anchors and supports sized to withstand the strong winds that can be encountered on the roofs of the Southwest, particularly near the Lachine Canal and major arteries.
2. Management of clearances and ventilation
The Sharp condenser is positioned so that:
-
Maintain sufficient clearance at the rear and sides to allow for optimal airflow;
-
Avoid recirculating hot air between the different units present on the roof (LG, other heat pumps);
-
Preserve an access corridor for maintenance, without hindering other mechanical equipment.
Good clearance is essential to guarantee the performance of the heat pump in the heat of summer as well as in periods of extreme cold.
3. Protected refrigeration and electrical connections
Refrigerant pipes and electrical cables are bundled, insulated, and protected within a conduit before being routed into the building. We pay particular attention to:
-
Insulating the lines to reduce energy losses;
-
Protection against UV rays, snow and ice;
-
The correct slope for the drainage of any condensate, where applicable.
This type of finish ensures the durability of the system and reduces the risk of leaks or premature breakage.
Interior: Custom-designed comfort for the condo
Although the photo focuses on the exterior, the system is connected to at least one Sharp wall head installed inside the apartment.
The advantages for the occupant:
-
High-performance air conditioning in summer , even in the middle of a heatwave;
-
Efficient heating in the shoulder seasons and winter , allowing relief from electric baseboard heaters or reducing the use of an existing system;
-
It is possible to adjust the temperature to within half a degree depending on the room.
The customer now has:
-
A silent system, with minimal noise inside;
-
A remote control (or wall controller) to adjust the temperature, mode, and fan speed;
-
Advanced functions (timers, dehumidification, sometimes Wi-Fi depending on the configuration).
Performance and Quebec winter
Installing a heat pump on a roof in Montreal requires thinking about winter first :
-
The height of the support allows the unit to breathe even when the roof is covered with snow;
-
The location facilitates automatic defrosting of the unit;
-
The customer benefits from more economical heating than electric baseboard heaters, while maintaining excellent reliability in cold weather .
Modern Sharp heat pumps are designed to operate in sub-zero temperatures, making them a very attractive option for a neighborhood like the Southwest, where older buildings stand alongside new towers and every gain in energy efficiency is felt on the bill.
Why choose AirGreen for a Sharp heat pump in the Southwest?
At AirGreen, we install and maintain Sharp wall-mounted heat pump systems throughout Greater Montreal: Southwest, Verdun, Ville-Marie, Rosemont, Laval, North Shore and South Shore.
By choosing us, you will benefit from:
-
From a personalized analysis of your accommodation (orientation, insulation, room configuration);
-
Appropriate sizing : we do not oversize, we do not undersize;
-
From a team of certified technicians, experienced in flat roofs, condominiums and access constraints;
-
Support for grant programs when available;
-
From a responsive after-sales service, with maintenance and repair throughout the lifetime of your system.
A similar project for your condo or apartment?
Whether you own a condo in the Southwest, rent a multi-unit building in Verdun, or live in an apartment in Ville-Marie, a Sharp ECO Inverter wall-mounted heat pump can transform your everyday comfort:
-
Pleasant and stable coolness in summer;
-
Economical heating for a large part of the winter;
-
Cleaner air thanks to Plasmacluster technology;
-
Discreet installation, both indoors and on the roof.
Want to know if this type of installation is possible in your home?
We will come to your home free of charge to assess your situation and offer you the best Sharp heat pump configuration for your home.
The big day, step by step
The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.
We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
Model, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
Floors and furniture protected, wall plate position marked level, wall opening located.
A single opening, with the slope the drain needs to flow outside.
Set on a stand raised above the snow, with the clearances the manufacturer requires.
Connected, insulated and protected. The opening is then sealed against water, cold air and insects.
A dedicated circuit and an accessible disconnect near the outdoor unit.
Leak test, vacuum, then start-up and a check of heating and cooling.
Remote, modes, filters: we show you the essentials before we leave.
- The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
- The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
- Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
- The wall openingA single opening, with the slope the drain needs to flow outside.
- The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
- Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
- The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
- Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
- The walkthroughRemote, modes, filters: we show you the essentials before we leave.
What would it look like at your place?
Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.
Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.
Four mistakes we do not make
Flip each card to see what we do instead.
Your own project, step by step
What to do, season by season
Three habits per season for this unit. They take a few minutes and prevent many calls.
- Clean the indoor unit's filters.
- Clear leaves and debris left on the outdoor unit by winter.
- Test cooling before the first hot days.
- Clean the filters more often when the unit runs a lot.
- Keep plants away from the outdoor unit.
- Check that no water drips from the indoor unit.
- Rake the leaves around the outdoor unit.
- Test heating before the first cold days.
- Book periodic maintenance before winter.
- Keep snow away from the stand and the front of the unit.
- Let the unit defrost: it is normal.
- Never hit the ice on the fins; call us if the unit stays iced up.
Is your home ready?
Check what applies at your place. A "no" is not a refusal: it is what we sort out during the estimate.
Four statements: true or false?
It all comes down to details you have just seen.
1. In heating mode, the outdoor unit can produce water.
During defrost cycles. That water must drain away without forming ice.
2. You pick the capacity with a simple square-footage rule.
Windows, insulation, orientation and how the room is used all count. Capacity is chosen on site.
3. A multi-zone connects several indoor heads to a single condenser.
One head per room, all on the same condenser. Each room keeps its own temperature.
4. The disconnect can sit behind the patio furniture.
It must stay accessible: it is what shuts the unit off for service.
0 / 4 right answers
What people ask us about this kind of work
Does a wall-mounted heat pump heat in winter?
Wall-mounted or multi-zone: how do I choose?
Where does the outdoor unit go?
Are there grants?
Do I need a permit?
How cold can it heat?
How much can I save?
How is the LogisVert assistance calculated?
Is it noisy?
The outdoor unit is covered in ice: is that normal?
Does AirGreen hold the required licences?
Is the estimate free?
No question matches. Write to us: we answer.
More jobs to see, near you
By town, by equipment or by region: browse more than 4,700 published projects.
Each dot: a town where AirGreen has published projects. The glowing dot: this job.
Every house has its constraints. We see them before we install.
The on-site estimate is free and the quote follows within 24 hours.
Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).
