Installation of a Zephyr wall-mounted heat pump in Ville-Marie
AirGreen installs a Zephyr wall-mounted heat pump in Ville-Marie: a compact, quiet and energy-efficient HVAC solution for Montreal, Laval, North Shore and South Shore.
- City
- Region
- Equipment
- Brand
- Challenges
- Published
The job on one screen

The article, chapter by chapter
Discreet and efficient comfort in a downtown condo
At AirGreen , we understand that installing a wall-mounted heat pump in an urban condo requires precision, discretion, and efficiency. This project in Ville-Marie , in the heart of Montreal, demonstrates our ability to adapt a modern, energy-efficient HVAC solution to a small space while maintaining the aesthetics of the interior.
Client context and needs
The occupants wanted a system that would provide four-season comfort , with efficient air conditioning during the summer heatwaves and reliable supplemental heating on icy days. Their priority: a quiet, compact unit that was easy to integrate into their minimalist interior. The Zephyr wall-mounted heat pump was the ideal choice.
The advantages of the Zephyr wall-mounted heat pump
The Zephyr range is renowned for its robustness and excellent value for money. The chosen model offers:
-
A capacity of 12,000 BTU , perfect for an open-plan condo.
-
Stable heating performance down to -25°C , ensuring comfort even in the middle of Montreal winter.
-
Energy efficiency that meets Energy Star standards, making it eligible for government subsidies.
-
Quiet operation, essential in a dense urban environment.
Installation process
Preparation and location
The indoor unit was installed on a central wall of the living room, near a large curtained window. This positioning optimizes air circulation and prevents areas of thermal stagnation.
Drilling and refrigeration connections
A precise drilling allowed the indoor unit to be connected to the exterior. The refrigeration connections and the electrical cable were carefully insulated and hidden behind discreet capping , ensuring a clean and harmonious finish with the white walls of the condo.
Condensate management
The condo's configuration allowed for gravity-fed condensate drainage , eliminating the need for an additional pump. This simple and reliable solution reduces future maintenance.
Installation of the outdoor unit
The outdoor unit was installed on a rear balcony , mounted on anti-vibration mounts to reduce noise and protect the compressor. This arrangement also facilitates access for seasonal maintenance.
Challenges encountered and solutions
-
Narrow wall with aesthetic constraints : we positioned the unit to avoid any contact with the curtains, ensuring uniform air diffusion.
-
Exterior space constraint : Due to the limited size of the balcony, we used compact brackets allowing sufficient clearance to ensure good ventilation around the compressor.
Results obtained
Once the system was up and running, the clients immediately appreciated the increased comfort and quietness of the Zephyr heat pump. Their condo now enjoys a stable temperature year-round, and energy costs are already reduced thanks to the system's efficiency.
AirGreen expertise serving downtown Montreal
At AirGreen, we understand the unique challenges of downtown condos : limited space, aesthetic constraints, and the need for quiet operation. Leveraging our expertise, we offer Zephyr wall-mounted heat pump installations tailored to the needs of Montreal, Laval, the North Shore, and the South Shore , while ensuring reliable, sustainable service that's eligible for available subsidies.
The job tools
Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.
Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.
How the job unfolds
The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.
We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
Model, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
Floors and furniture protected, wall plate position marked level, wall opening located.
A single opening, with the slope the drain needs to flow outside.
Set on a stand raised above the snow, with the clearances the manufacturer requires.
Connected, insulated and protected. The opening is then sealed against water, cold air and insects.
A dedicated circuit and an accessible disconnect near the outdoor unit.
Leak test, vacuum, then start-up and a check of heating and cooling.
Remote, modes, filters: we show you the essentials before we leave.
- The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
- The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
- Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
- The wall openingA single opening, with the slope the drain needs to flow outside.
- The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
- Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
- The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
- Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
- The walkthroughRemote, modes, filters: we show you the essentials before we leave.
What we check on a job like this one
Each number is a point we check on site. Switch between summer and winter to watch air and heat move.
In summer, the outdoor unit rejects the house's heat outside.
Generic illustration of this type of installation, not a survey of this job site. Tap a number.
Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.
The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.
Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.
A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.
The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.
On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.
The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.
Is your home ready?
Check what applies at your place. A "no" is not a refusal: it is what we sort out during the estimate.
Good habits, once the unit is in place
Six simple habits that keep the unit going. Your list stays on this device.
What to do, season by season
Three habits per season for this unit. They take a few minutes and prevent many calls.
- Clean the indoor unit's filters.
- Clear leaves and debris left on the outdoor unit by winter.
- Test cooling before the first hot days.
- Clean the filters more often when the unit runs a lot.
- Keep plants away from the outdoor unit.
- Check that no water drips from the indoor unit.
- Rake the leaves around the outdoor unit.
- Test heating before the first cold days.
- Book periodic maintenance before winter.
- Keep snow away from the stand and the front of the unit.
- Let the unit defrost: it is normal.
- Never hit the ice on the fins; call us if the unit stays iced up.
The right pages, at the right time
Four statements: true or false?
It all comes down to details you have just seen.
1. In heating mode, the outdoor unit can produce water.
During defrost cycles. That water must drain away without forming ice.
2. You pick the capacity with a simple square-footage rule.
Windows, insulation, orientation and how the room is used all count. Capacity is chosen on site.
3. A multi-zone connects several indoor heads to a single condenser.
One head per room, all on the same condenser. Each room keeps its own temperature.
4. The disconnect can sit behind the patio furniture.
It must stay accessible: it is what shuts the unit off for service.
0 / 4 right answers
What people ask us about this kind of work
Does a wall-mounted heat pump heat in winter?
Wall-mounted or multi-zone: how do I choose?
Where does the outdoor unit go?
Are there grants?
Do I need a permit?
How cold can it heat?
How much can I save?
How is the LogisVert assistance calculated?
Is it noisy?
The outdoor unit is covered in ice: is that normal?
Does AirGreen hold the required licences?
Is the estimate free?
No question matches. Write to us: we answer.
More jobs to see, near you
By town, by equipment or by region: browse more than 4,700 published projects.
Each dot: a town where AirGreen has published projects. The glowing dot: this job.
An on-site estimate, the right capacity, the right equipment.
The on-site estimate is free and the quote follows within 24 hours.
Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).
