Project

Sharp wall-mounted heat pump installation in Verdun

On a rooftop terrace in Verdun, AirGreen installed a Sharp ZU1 wall-mounted heat pump for an open-concept condo. Elevated supports, vibration management, heating and cooling performance: discover how we optimized occupant comfort while respecting the building's structure.

By AirGreen Climatisation & Chauffage Admin5 min read
Sharp wall-mounted heat pump installation in Verdun
Sharp wall-mounted heat pump installation in Verdun
–chapters in this story
5 minreading time
–type of installation
2026year published
The tour

Take a tour of the installation

Each number is a point we check on site. Switch between summer and winter to watch air and heat move.

Generic diagram: wall-mounted heat pump, indoor and outdoor units

In summer, the outdoor unit rejects the house's heat outside.

Generic illustration of this type of installation, not a survey of this job site. Tap a number.

  1. Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.

  2. The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.

  3. Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.

  4. A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.

  5. The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.

  6. On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.

  7. The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.

The job

In Verdun, on the rooftop terrace of a residential building overlooking the river, our team installed aSharp wall-mounted heat pump to provide year-round comfort for the occupants of an open-concept condo. The installation took place in an environment already equipped with several outdoor units, requiring a configuration that was efficient, safe, and aesthetically pleasing.


Context: a typical rooftop terrace in Verdun

The building is a typical multi-unit dwelling for the area: timber frame construction, large rooftop terrace, wooden railings, and unobstructed views. The client wanted:

  • Replacing an old, noisy, and inefficient system;

  • Maximize comfort in both summer and winter;

  • Keep the terrace space usable and safe;

  • Limit the vibrations transmitted to the building structure.

The choice of a Sharp wall-mounted heat pump emerged as an ideal solution for this type of urban building: heating performance, compact outdoor unit and proven reliability.


Choosing the Sharp wall-mounted heat pump

For this project, we opted for a Sharp ZU1 series wall-mounted heat pump , in the 18,000 BTU version, perfectly suited to a condo of approximately 900 to 1,000 sq ft with an open living-dining-kitchen area.

Among the advantages of this range:

  • High energy efficiency technology , allowing for a significant reduction in electricity costs compared to older window air conditioners or basic electrical systems;

  • Stable operation in heating mode in cold weather , suitable for Montreal's climate;

  • Use of a new generation refrigerant that is more efficient and complies with current environmental standards;

  • Reduced noise level , much appreciated in a dense urban living environment like Verdun.


A neat outdoor installation on the roof

The photo clearly shows several condensers installed on a gravel-covered roof. Our Sharp unit is positioned on galvanized steel supports resting on wooden beams laid on the membrane, which allows:

  • to distribute the load and protect the roof membrane;

  • to ensure adequate clearance under the unit for drainage and air circulation;

  • to limit the transmission of vibrations to the structure.

Key features of our installation:

  • Orientation of the unit to optimize airflow and maintain sufficient clearance from the guardrail and other condensers;

  • Use of stainless and galvanized hardware , resistant to weathering and salt, particularly important near the river;

  • Orderly routing of refrigeration lines (refrigerant), condensation drain and power supply, in order to reduce the risk of machining of the membrane while maintaining the overall aesthetic;

  • Clear access for maintenance , to facilitate preventive maintenance visits (battery cleaning, connection checks, pressure checks, etc.).


Interior: comfort and discretion

Inside, the Sharp wall-mounted head unit is installed in the main living area:

  • Positioned at an optimal height for even air distribution in the open area;

  • Calibrated to avoid direct air currents on occupants, while ensuring effective air circulation;

  • Connected to a condensation drain routed to the outside, preventing any risk of dripping into the dwelling.

Thanks to the variable speed compressor, the heat pump continuously adjusts its power:

  • in air conditioning mode , to maintain a stable temperature even during heat waves;

  • in heating mode , to ensure gentle and constant comfort during the winter, while reducing reliance on electric baseboard heaters.


Noise and vibration management

In dense urban environments, noise management is a major challenge. We paid particular attention to:

  • the use of anti-vibration mounts under the condenser;

  • controlled tightening of the bolts, in order to avoid buzzing noises;

  • strategic positioning of the outdoor unit, at a reasonable distance from the resting areas of neighbors on the roof.

The result: a Sharp heat pump that operates discreetly, both for the owner and the neighborhood.


Performance and energy savings

With his Sharp wall-mounted heat pump, the Verdun customer now benefits from:

  • four-season comfort : coolness in summer, warmth in winter, dehumidification in the off-season;

  • reduced electricity bills , thanks to a high coefficient of performance in heating and excellent efficiency in air conditioning;

  • of added real estate value , the presence of a modern and efficient heat pump being an asset for the resale or rental of the condo.

The installation complies with current electrical and mechanical standards as well as best practices recommended by manufacturers and energy efficiency programs in Quebec.


Why trust AirGreen for your Sharp heat pump in Verdun?

At AirGreen, we support condo, plex and house owners throughout Verdun and Greater Montreal with their heating and air conditioning projects:

  • Personalized needs analysis : surface area, insulation, orientation, lifestyle habits;

  • Recommending the right Sharp model based on budget, desired performance level and architectural constraints;

  • Professional and careful installation , respecting the building structure and the roof membrane;

  • After-sales service and maintenance to guarantee the longevity of the equipment and maintain its performance over the years.

If you live in Verdun or elsewhere in Greater Montreal and are considering installing a Sharp wall-mounted heat pump , our team is ready to offer you a turnkey solution, from initial consultation to first start-up.

The steps

The big day, step by step

The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.

Step 1 of 9The on-site estimate

We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.

  1. The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
  2. The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
  3. Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
  4. The wall openingA single opening, with the slope the drain needs to flow outside.
  5. The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
  6. Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
  7. The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
  8. Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
  9. The walkthroughRemote, modes, filters: we show you the essentials before we leave.
Your numbers

What would it look like at your place?

Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.

Size checkYour baseboards, in BTU/h
–BTU/h of installed electric heat

    Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.

    Mistakes avoided

    Four mistakes we do not make

    Flip each card to see what we do instead.

    Going further

    Your own project, step by step

    Through the seasons

    What to do, season by season

    Three habits per season for this unit. They take a few minutes and prevent many calls.

    • Clean the indoor unit's filters.
    • Clear leaves and debris left on the outdoor unit by winter.
    • Test cooling before the first hot days.
    At your place

    Is your home ready?

    Check what applies at your place. A "no" is not a refusal: it is what we sort out during the estimate.

    0 / 6 checked
    True or false

    Four statements: true or false?

    It all comes down to details you have just seen.

    1. In heating mode, the outdoor unit can produce water.

    2. You pick the capacity with a simple square-footage rule.

    3. A multi-zone connects several indoor heads to a single condenser.

    4. The disconnect can sit behind the patio furniture.

    Frequently asked questions

    What people ask us about this kind of work

    12 questions
    Does a wall-mounted heat pump heat in winter?
    Yes, it heats and cools. Its capacity drops in very cold weather; the operating range depends on the model and is listed on its spec sheet.
    Wall-mounted or multi-zone: how do I choose?
    One wall head and one condenser outside: the direct solution for a room or an open area. For two to five rooms, a multi-zone puts one head in each room on a single condenser.
    Where does the outdoor unit go?
    Where it stays above the snow, clear and accessible, away from walkways. We decide it with you during the estimate.
    Are there grants?
    Depending on the model and your situation, assistance programs may apply, including Hydro-Québec's LogisVert. AirGreen checks the model number before quoting an amount. See the grants.
    Do I need a permit?
    Rules vary from city to city: location, distances, noise. See permits and by-laws, and we check for your address.
    How cold can it heat?
    It depends on the model. According to Hydro-Québec, newer models work down to a temperature between −15 °C and −25 °C, and some cold-climate models are certified lower. The minimum temperature is on each unit's spec sheet.
    How much can I save?
    Hydro-Québec says a heat pump can be up to three times more efficient than baseboards for heating in the colder months. The result depends on the house, the climate and how it is used.
    How is the LogisVert assistance calculated?
    For ENERGY STAR cold-climate certified heat pumps, Hydro-Québec lists assistance of $120 per 1,000 BTU/h of heating capacity at −8 °C. AirGreen checks the exact model before quoting an amount; only Hydro-Québec confirms the assistance granted. See the grants.
    Is it noisy?
    The sound level depends on the model and is listed in decibels on each unit's spec sheet. Location matters too: when possible, we avoid putting the outdoor unit under a bedroom window.
    The outdoor unit is covered in ice: is that normal?
    Some frost is: the unit runs defrost cycles. Never hit the ice. If the unit stays iced up or stops heating, call us.
    Does AirGreen hold the required licences?
    Yes. AirGreen holds RBQ licence 5645-9605-01, subclasses 15.8 Ventilation, 15.10 Refrigeration and 16 Electricity.
    Is the estimate free?
    Yes. The on-site estimate is free and the quote follows within 24 hours. Book my free estimate.

    Could this job help a neighbour?

    Share
    Similar projects

    More jobs to see, near you

    By town, by equipment or by region: browse more than 4,700 published projects.

    Each dot: a town where AirGreen has published projects. The glowing dot: this job.

    All our projects

    Your project

    Every house has its constraints. We see them before we install.

    The on-site estimate is free and the quote follows within 24 hours.

    • RBQ licence5645-9605-01 · 15.8, 15.10, 16
    • EstimateOn site, free
    • QuoteWithin 24 hours

    Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).

    Leave a comment