Installation of Sharp wall-mounted heat pumps in Rosemont–La Petite-Patrie
AirGreen installed two high-efficiency Sharp wall-mounted heat pumps in a building in Rosemont–La Petite-Patrie, mounting the units on wall brackets in a narrow passageway. The result: year-round comfort, energy savings, and a sleek exterior finish perfectly suited to Montreal's climate.

Take a tour of the installation
Each number is a point we check on site. Switch between summer and winter to watch air and heat move.
In summer, the outdoor unit rejects the house's heat outside.
Generic illustration of this type of installation, not a survey of this job site. Tap a number.
Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.
The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.
Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.
A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.
The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.
On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.
The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.
In this project, our AirGreen team worked in a typical Rosemont–La Petite-Patrie residential building to modernize occupant comfort by installing two high-efficiency Sharp wall-mounted heat pumps . The building, composed of stacked apartments, had a narrow side passage between two brick facades: a perfect environment for a meticulous installation… but one that was technically demanding.
The client's need: four-season comfort, without wasting space
The owners wanted:
-
To efficiently air-condition and heat two dwellings;
-
Reduce their reliance on traditional electric heating, which is very energy-intensive in winter;
-
Preserve the aesthetics of the brick facades;
-
Minimize the floor space required in the passage, which is already very narrow.
Our advisors therefore recommended the installation of two Sharp wall-mounted heat pumps , each dedicated to a dwelling, in order to offer independent temperature control and valuable redundancy in case of high demand.
System type selected: Sharp ZU1 wall-mounted heat pumps (R-32)
For this project, we opted for the Sharp ZU1 range (R-32 wall-mounted heat pumps), known for:
-
Its excellent heating performance in cold weather ;
-
Its high energy efficiency inverter compressor ;
-
Its silent operation, both indoors and outdoors;
-
The use of R-32 refrigerant, which is more efficient and more environmentally friendly than R-410A.
Each Sharp wall unit serves a separate dwelling, providing:
-
Air conditioning in summer , even during periods of intense heat;
-
Stable and comfortable heating throughout much of the Montreal winter, even in sub-zero temperatures typical of our winters.
A narrow installation site: a real clearance challenge
The passage between the two brick buildings is particularly narrow. In this context, several technical aspects had to be managed meticulously:
1. Clearances and air circulation
Even in a narrow corridor, a heat pump needs to be able to breathe :
-
We fixed the two Sharp condensers on a sturdy wall bracket , at a good height, to clear the floor area and ensure optimal air circulation.
-
The side-by-side arrangement respects the minimum distances between the devices, in order to avoid the recirculation of hot air in heating mode or cold air in air conditioning mode.
2. Protection against snow and ice
In winter, the accumulation of snow and ice on the ground can impair the performance and durability of appliances:
-
The raised wall mounting helps protect Sharp units from snowbanks and runoff.
-
The passage is covered with river stones , promoting drainage and limiting splashing on equipment.
3. Safe access to heights
The refrigeration and electrical lines had to be routed vertically over several meters:
-
We used a telescopic ladder to work safely at height.
-
The technicians took care to securely fix the duct covers all along the brick wall, up to the point of entry to the dwellings.
Finish: Discreet and aesthetically pleasing refrigerant lines
In an urban environment like Rosemont–La Petite-Patrie, the aesthetics of facades matter a lot to owners.
-
The insulated pipes (refrigerant, condensate drain, power supply) are protected by a neutral colour cover , installed vertically.
-
The hood follows the line of the wall up to the service entrances, resulting in a clean, aligned and discreet appearance.
-
The wiring and pipes are carefully secured to prevent any vibration or premature wear.
The result: the installation blends naturally into the passageway, without giving the impression of "DIY" or visual clutter.
Inside: targeted comfort and precise control
Although the photo only shows the exterior, the indoor units chosen are Sharp wall-mounted heads with a sleek design , installed in the main living areas of each dwelling.
The occupants thus benefit from:
-
Rapid cooling during the intense summer heat;
-
Providing pleasant heating during the shoulder seasons and for much of the winter;
-
Precise temperature control thanks to remote controls and programmable modes;
-
With quiet operation, ideal for bedrooms and living rooms.
Energy efficiency and long-term savings
By replacing or supplementing traditional electric heating with high-efficiency Sharp wall-mounted heat pumps , homeowners can:
-
To significantly reduce their electricity bill , especially in winter;
-
Benefit from a favorable COP (coefficient of performance) , i.e. more heat produced for each kWh consumed;
-
Reducing their carbon footprint , thanks to the R-32 refrigerant and optimized consumption.
Over several years, energy savings help to recoup the investment while increasing comfort and the overall value of the building.
Safety, compliance and reliability
At AirGreen, we pay particular attention to:
-
To the sizing of electrical circuits and protection by circuit breaker;
-
To the leveling of the wall supports and anchoring in the brick;
-
Vacuuming and refrigerant charging in accordance with Sharp specifications;
-
Functional tests in cold and hot mode before handover to the customer.
At the end of the project, the owners receive all the essential information: documentation for the devices, maintenance instructions, and recommendations to maximize the lifespan of the heat pumps.
A typical comfort optimization project in Rosemont–La Petite-Patrie
This project perfectly illustrates what we accomplish every week in Greater Montreal:
-
Upgrading comfort in existing brick buildings;
-
Adaptation to space constraints (narrow passages, courtyards, alleyways);
-
Integration of high-performance Sharp wall-mounted heat pumps , adapted to the Quebec climate.
The occupants of this building in Rosemont–La Petite-Patrie now benefit from:
-
Four-season comfort;
-
Better controlled energy bills;
-
With a carefully designed exterior installation that respects the building's aesthetics.
Why choose AirGreen for your Sharp heat pump in Montreal?
By choosing AirGreen, you benefit from:
-
Certified technicians , experienced in complex installations in urban environments;
-
Personalized advice to choose the right capacity and range for Sharp;
-
A compliant and durable installation , designed for Montreal's harsh winters;
-
With a human and responsive after-sales service .
Whether you are in Rosemont–La Petite-Patrie, on the Plateau, in Laval or on the South Shore, we are here to help you modernize your comfort with Sharp wall-mounted heat pump solutions adapted to your building.
The big day, step by step
The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.
We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
Model, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
Floors and furniture protected, wall plate position marked level, wall opening located.
A single opening, with the slope the drain needs to flow outside.
Set on a stand raised above the snow, with the clearances the manufacturer requires.
Connected, insulated and protected. The opening is then sealed against water, cold air and insects.
A dedicated circuit and an accessible disconnect near the outdoor unit.
Leak test, vacuum, then start-up and a check of heating and cooling.
Remote, modes, filters: we show you the essentials before we leave.
- The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
- The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
- Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
- The wall openingA single opening, with the slope the drain needs to flow outside.
- The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
- Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
- The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
- Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
- The walkthroughRemote, modes, filters: we show you the essentials before we leave.
What would it look like at your place?
Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.
Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.
Four mistakes we do not make
Flip each card to see what we do instead.
Your own project, step by step
What to do, season by season
Three habits per season for this unit. They take a few minutes and prevent many calls.
- Clean the indoor unit's filters.
- Clear leaves and debris left on the outdoor unit by winter.
- Test cooling before the first hot days.
- Clean the filters more often when the unit runs a lot.
- Keep plants away from the outdoor unit.
- Check that no water drips from the indoor unit.
- Rake the leaves around the outdoor unit.
- Test heating before the first cold days.
- Book periodic maintenance before winter.
- Keep snow away from the stand and the front of the unit.
- Let the unit defrost: it is normal.
- Never hit the ice on the fins; call us if the unit stays iced up.
Is your home ready?
Check what applies at your place. A "no" is not a refusal: it is what we sort out during the estimate.
Four statements: true or false?
It all comes down to details you have just seen.
1. In heating mode, the outdoor unit can produce water.
During defrost cycles. That water must drain away without forming ice.
2. You pick the capacity with a simple square-footage rule.
Windows, insulation, orientation and how the room is used all count. Capacity is chosen on site.
3. A multi-zone connects several indoor heads to a single condenser.
One head per room, all on the same condenser. Each room keeps its own temperature.
4. The disconnect can sit behind the patio furniture.
It must stay accessible: it is what shuts the unit off for service.
0 / 4 right answers
What people ask us about this kind of work
Does a wall-mounted heat pump heat in winter?
Wall-mounted or multi-zone: how do I choose?
Where does the outdoor unit go?
Are there grants?
Do I need a permit?
How cold can it heat?
How much can I save?
How is the LogisVert assistance calculated?
Is it noisy?
The outdoor unit is covered in ice: is that normal?
Does AirGreen hold the required licences?
Is the estimate free?
No question matches. Write to us: we answer.
More jobs to see, near you
By town, by equipment or by region: browse more than 4,700 published projects.
Each dot: a town where AirGreen has published projects. The glowing dot: this job.
Every house has its constraints. We see them before we install.
The on-site estimate is free and the quote follows within 24 hours.
Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).
