Installation of a GREE LIVO R32 Wall-Mounted Heat Pump in Côte-des-Neiges
Discover the installation of a GREE LIVO R32 wall-mounted heat pump in Côte-des-Neiges. This high-performance and energy-efficient model ensures comfort all year round. Trust AirGreen for your HVAC projects in Montreal, Laval, and beyond.
In summer, the outdoor unit rejects the house's heat outside.
Generic illustration of this type of installation, not a survey of this job site. Tap a number.
Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.
The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.
Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.
A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.
The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.
On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.
The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.
A Choice of Quality and Energy Efficiency
At AirGreen, we are committed to offering heating, ventilation, and air conditioning (HVAC) solutions that combine performance, reliability, and energy savings. A recent installation of a GREE LIVO R32 wall-mounted heat pump in Côte-des-Neiges is a prime example. This model is an ideal choice for those looking to enhance their comfort while benefiting from exceptional energy efficiency.
Why Choose the GREE LIVO R32 Heat Pump?
The GREE LIVO R32 model stands out for its advanced technical features and its ability to provide optimal comfort in a variety of climatic conditions. With extensive cooling and heating capacity, it is designed to meet the needs of residents in areas such as Montreal, Laval, and Longueuil, where temperatures can vary significantly.
Energy Efficiency and Performance
The GREE LIVO R32 wall-mounted heat pump offers impressive performance:
-
SEER2 (Seasonal Energy Efficiency Ratio): up to 20.5, which helps reduce energy consumption during the hot months.
-
EER2 (Energy Efficiency Ratio): up to 12.5, ensuring optimal performance during periods of heat.
-
HSPF2 (Heating Seasonal Performance Factor): up to 8.8, ideal for cold winters.
It is also compatible with cold climates, capable of maintaining its heating performance down to -13°F (-25°C), making it perfect for the Quebec climate.
Innovative Features
The GREE LIVO R32 comes equipped with several features that enhance both efficiency and user experience:
-
Auto Clean: for easy maintenance and optimal air quality.
-
I-Feel: detects the temperature around the remote control and adjusts it for more comfort.
-
Auto-diagnosis: makes it easy to detect and resolve any issues.
-
Swing louver control: for even air distribution.
The Installation Process in Côte-des-Neiges
The installation of this GREE LIVO R32 heat pump in Côte-des-Neiges, in a residential apartment, required special attention to various aspects, including integration into a limited space while maximizing energy efficiency.
Challenges Faced and Solutions Provided
As with many urban installations, the primary challenge was the limited space in the apartment. AirGreen technicians had to ensure that the outdoor unit was placed in such a way as to optimize thermal exchange, while respecting the building’s insulation and ventilation standards.
Moreover, thanks to the flexibility of the GREE LIVO R32, refrigerant pipes could be installed up to 40 feet, allowing the outdoor unit to be positioned without compromising the building’s aesthetics. This model, featuring the 115V option, was perfect for this residential installation, offering optimal performance without requiring a large power supply.
Installation Time
The installation was completed within 4 hours, including the setup of both the indoor and outdoor units, as well as final testing to ensure flawless performance. The homeowners were instructed on how to use the remote control and advanced features, such as auto-cleaning and automatic temperature regulation.
The Benefits for the Homeowner
One of the main advantages for the homeowners of this GREE LIVO R32 installation is its energy efficiency. By reducing energy consumption and providing more precise control over heating and cooling, this heat pump contributes to significant savings on energy bills.
Additionally, this installation is eligible for Hydro-Québec subsidies, such as the Rénoclimat program, allowing the client to benefit from financial assistance to make the installation even more affordable.
Customer Testimonial
Here’s what the client said after the installation:
"We chose AirGreen for their expertise and reputation in installing quality heat pumps. The team met our expectations by installing a high-performance system that fits our space. We are thrilled with the air quality and thermal comfort we now enjoy in our apartment."
Why Choose AirGreen for Your HVAC Installations?
At AirGreen, we understand the importance of selecting the right equipment for your home or business. We are dedicated to providing heat pump and air conditioning installations that are not only efficient and eco-friendly but also tailored to your specific needs.
Our certified technicians possess the expertise necessary to complete an installation quickly and with the highest quality, while ensuring attention to every detail of the process.
Conclusion
The installation of the GREE LIVO R32 wall-mounted heat pump in Côte-des-Neiges provided our client with a heating and cooling solution that combines energy efficiency, comfort, and performance. With its modern design and advanced features, this model is perfectly suited to the needs of residents in Montreal, Laval, Longueuil, and surrounding areas. Trust AirGreen with your heat pump installation project and experience the difference that professional installation can make.
How it goes, from the first call to the end
The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.
We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
Model, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
Floors and furniture protected, wall plate position marked level, wall opening located.
A single opening, with the slope the drain needs to flow outside.
Set on a stand raised above the snow, with the clearances the manufacturer requires.
Connected, insulated and protected. The opening is then sealed against water, cold air and insects.
A dedicated circuit and an accessible disconnect near the outdoor unit.
Leak test, vacuum, then start-up and a check of heating and cooling.
Remote, modes, filters: we show you the essentials before we leave.
- The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
- The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
- Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
- The wall openingA single opening, with the slope the drain needs to flow outside.
- The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
- Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
- The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
- Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
- The walkthroughRemote, modes, filters: we show you the essentials before we leave.
What the unit delivers when it is cold
The range as published on airgreen.ca: pick a size to see its capacity in deep cold.
| Size | Heating at −8 °C | Heating at −15 °C | Coldest certified point | COP at −15 °C | SEER | HSPF | Indicative LogisVert aid |
|---|---|---|---|---|---|---|---|
| Gree Livo R32 9 000 (115 V) | 10,000 | 7,600 | −25 °C: 5,700 | 1.86 | 20.5 | 8.8 | – |
| Gree Livo R32 9 000 | 9,600 | 7,600 | −25 °C: 5,500 | 1.94 | 20.5 | 8.8 | – |
| Gree Livo R32 12 000 (115 V) | 9,700 | 8,500 | −25 °C: 6,500 | 1.75 | 19.0 | 8.5 | – |
| Gree Livo R32 12 000 | 9,700 | 9,100 | −25 °C: 6,500 | 1.8 | 19.0 | 8.5 | $1,164 |
| Gree Livo R32 18 000 | 15,300 | 12,100 | −25 °C: 10,200 | 1.85 | 20.0 | 8.5 | $1,836 |
| Gree Livo R32 24 000 | 19,200 | 15,700 | −25 °C: 10,500 | 1.75 | 19.0 | 8.5 | $2,304 |
| Gree Livo R32 30 000 | 24,000 | 23,000 | −25 °C: 16,900 | 1.8 | 22.0 | 9.0 | $2,880 |
| Gree Livo R32 36 000 | 27,400 | 24,600 | −25 °C: 21,000 | 1.8 | 21.0 | 8.5 | $3,288 |
According to NEEP, it delivers 10,000 BTU/h at −8 °C (17 °F), as much as at 8 °C. It heats as hard in moderate cold as in mild weather.
According to NEEP, its certified maximum capacity at −25 °C (−13 °F) is 5,700 BTU/h, 63% of its nominal 9,000 BTU size.
At 8 °C, its certified maximum capacity reaches 13,300 BTU/h, 48% more than its nominal 9,000 BTU size.
According to NEEP, its COP at −15 °C is 1.94: the highest of the Livo R32 line, which ranges from 1.75 to 1.86 at that temperature.
According to NEEP, its certified maximum capacity at −25 °C (−13 °F) is 5,500 BTU/h, 61% of its nominal 9,000 BTU size.
At 8 °C, its certified maximum capacity reaches 13,136 BTU/h, 46% more than its nominal 9,000 BTU size.
According to NEEP, it delivers 8,500 BTU/h at −15 °C, against 9,100 for the Gree Livo R32 12 000.
At −25 °C, its certified minimum capacity is 1,800 BTU/h (3,070 at 8 °C). It slows down instead of cycling on and off.
According to NEEP, its certified heating capacity at −15 °C (5 °F) is 8,500 BTU/h, 71% of its nominal 12,000 BTU size. Its COP there is 1.75.
According to NEEP, it delivers 9,100 BTU/h at −15 °C, against 8,500 for the Gree Livo R32 12 000 (115 V).
At −25 °C, its certified minimum capacity is 1,800 BTU/h (3,070 at 8 °C). It slows down instead of cycling on and off.
According to NEEP, its certified heating capacity at −15 °C (5 °F) is 9,100 BTU/h, 76% of its nominal 12,000 BTU size. Its COP there is 1.80.
At 8 °C, its certified maximum capacity reaches 22,500 BTU/h, 25% more than its nominal 18,000 BTU size.
According to NEEP, its certified minimum capacity is at least 7,000 BTU/h at every temperature. In a small, well-insulated room it will cycle on and off more often: size it carefully.
According to NEEP, its certified heating capacity at −15 °C (5 °F) is 12,100 BTU/h, 67% of its nominal 18,000 BTU size. Its COP there is 1.85.
At −25 °C, its certified minimum capacity is 3,100 BTU/h (5,800 at 8 °C). It slows down instead of cycling on and off.
According to NEEP, its certified heating capacity at −15 °C (5 °F) is 15,700 BTU/h, 65% of its nominal 24,000 BTU size. Its COP there is 1.75.
According to NEEP, its certified heating capacity at −15 °C (5 °F) is 23,000 BTU/h, 77% of its nominal 30,000 BTU size. Its COP there is 1.80.
According to NEEP, its COP at −25 °C is 1.54: the highest of the Livo R32 line, which ranges from 1.30 to 1.52 at that temperature.
At −25 °C, its certified minimum capacity is 7,000 BTU/h (10,000 at 8 °C). It slows down instead of cycling on and off.
According to NEEP, its certified heating capacity at −15 °C (5 °F) is 24,600 BTU/h, 68% of its nominal 36,000 BTU size. Its COP there is 1.80.
Data read live from the airgreen.ca page of each size (NEEP / AHRI certified performance). When the title names the installed size, it is highlighted; otherwise the whole range is shown. The aid shown is today’s, using Hydro-Québec’s rule ($120 per 1,000 BTU/h at −8 °C); amounts quoted in the article date from its publication. Only Hydro-Québec confirms the assistance granted.A dash in the aid column: amount to be confirmed for this model.
And at your place?
Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.
Baseboards and electric furnaces turn 1 kWh of electricity into 1 kWh of heat. A heat pump delivers more: that is its COP. At Hydro-Québec’s rate D (11.142¢/kWh above 40 kWh a day, since 1 April 2026):
Hydro-Québec: a heat pump can be up to three times more efficient than baseboards for heating in the colder months.
Estimate per kWh of heat, at the chosen temperature, using the certified COP from the product page. Taxes, access charge and backup heat not included.
Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.
What to do, season by season
Three habits per season for this unit. They take a few minutes and prevent many calls.
- Clean the indoor unit's filters.
- Clear leaves and debris left on the outdoor unit by winter.
- Test cooling before the first hot days.
- Clean the filters more often when the unit runs a lot.
- Keep plants away from the outdoor unit.
- Check that no water drips from the indoor unit.
- Rake the leaves around the outdoor unit.
- Test heating before the first cold days.
- Book periodic maintenance before winter.
- Keep snow away from the stand and the front of the unit.
- Let the unit defrost: it is normal.
- Never hit the ice on the fins; call us if the unit stays iced up.
Which type of equipment for your project?
Pick what looks like your need.
Four mistakes we do not make
Flip each card to see what we do instead.
What people ask us about this kind of work
Does a wall-mounted heat pump heat in winter?
Wall-mounted or multi-zone: how do I choose?
Where does the outdoor unit go?
Are there grants?
Do I need a permit?
How cold can it heat?
How much can I save?
How is the LogisVert assistance calculated?
Is it noisy?
The outdoor unit is covered in ice: is that normal?
Does AirGreen hold the required licences?
Is the estimate free?
No question matches. Write to us: we answer.
Useful pages for what comes next
More jobs to see, near you
By town, by equipment or by region: browse more than 4,700 published projects.
Each dot: a town where AirGreen has published projects. The glowing dot: this job.
Tell us about your house. We come and see it for free.
The on-site estimate is free and the quote follows within 24 hours.
Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).