Project

Installation of a Sharp BU Triple Zone Heat Pump in the North Shore

Discover how our Sharp BU Triple Zone Heat Pump installation in the North Shore brings cutting-edge comfort and energy efficiency to homes, even in harsh winters. Learn more about this innovative HVAC system.

By AirGreen Climatisation & Chauffage Admin7 min read
Installation of a Sharp BU Triple Zone Heat Pump in the North Shore
Installation of a Sharp BU Triple Zone Heat Pump in the North Shore
–chapters in this story
7 minreading time
–type of installation
2024year published
The tour

Take a tour of the installation

Each number is a point we check on site. Switch between summer and winter to watch air and heat move.

Generic diagram: wall-mounted heat pump, indoor and outdoor units

In summer, the outdoor unit rejects the house's heat outside.

Generic illustration of this type of installation, not a survey of this job site. Tap a number.

  1. Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.

  2. The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.

  3. Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.

  4. A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.

  5. The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.

  6. On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.

  7. The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.

The job

Optimizing Comfort with AirGreen's Precision: A Sharp BU Installation Success Story

At AirGreen, we take pride in delivering high-quality HVAC solutions to homes and businesses across Montreal, Laval, Longueuil, the North Shore, and the South Shore. Recently, we had the opportunity to install a Sharp BU Triple Zone Heat Pump at a residence on the North Shore, showcasing the machine's efficiency, adaptability, and the professional workmanship that sets AirGreen apart from the competition.

The Installation Location: A Perfect Match for the North Shore’s Weather

The North Shore, known for its frigid winters and warm summers, presents a unique challenge for home climate control. This is where the Sharp BU Triple Zone Heat Pump comes into play. Our clients were seeking a system that could handle both extremes, providing cool relief during the summer months and reliable heating during the harsh winters. The solution was clear: a 24,000 BTU compressor paired with three indoor units (9,000 BTU each), all perfectly suited for zone-specific temperature control in their home.

Installation of a Sharp BU Triple Zone Heat Pump in the North Shore

Why the Sharp BU Triple Zone Heat Pump?

This Sharp BU model stands out due to its energy efficiency, versatile installation options, and impressive cooling and heating capacities. With an outdoor compressor capable of maintaining heating even at temperatures as low as -27°C, this system is built for Montreal’s unpredictable winters. Its cooling capacity of 24,000 BTUs ensures consistent comfort in the heat of the summer, making it the ideal system for the client’s needs.

Some notable features of this installation include:

  • Triple Zone Capability: With three indoor units, each operating independently, homeowners can control the temperature in different parts of the house, ensuring comfort without wasting energy on unoccupied rooms.
  • Energy Star® Certification: This system offers outstanding energy efficiency with a SEER rating of 24.0, ensuring significant energy savings, especially when combined with our precise installation.
  • WiFi Connectivity: The system includes built-in WiFi control, allowing the homeowner to manage the temperature from anywhere via their smartphone, ensuring comfort and efficiency at all times.

The Installation Process: A Seamless Experience

Our installation team at AirGreen took special care to ensure the project was completed with minimal disruption to the homeowners' daily lives. The three indoor units were strategically placed to maximize airflow and comfort, each serving its designated area with 9,000 BTU of power. These units provide the right balance between functionality and aesthetic integration into the home’s décor, as evident from the pictures taken post-installation.

The outdoor 24,000 BTU compressor was installed in a well-ventilated location, ensuring optimal performance year-round. With dimensions of 33.47 x 13 x 27.94, the compressor is compact yet powerful, designed to withstand the rigors of the North Shore climate. We also ensured that the installation met all energy efficiency guidelines, qualifying the homeowner for a substantial rebate under the Hydro-Québec LogisVert Grant—up to $3,000 in savings!

A Backstory of Efficiency and Innovation

This installation wasn’t just another routine job for us. The homeowners had reached out to AirGreen after months of struggling with an older system that could no longer keep up with the demands of their home’s changing needs. They were particularly concerned about reducing their carbon footprint while maintaining a comfortable living environment. After a thorough consultation, we recommended the Sharp BU Triple Zone Heat Pump as the perfect solution.

With R-32 refrigerant, this system is at the forefront of sustainable HVAC solutions, offering greater energy efficiency and a lower global warming potential (GWP) compared to older refrigerants like R-22 and R-410A. This choice aligns with the homeowners' desire for a more environmentally responsible system without compromising on comfort or performance.

Cutting-edge Technology for Modern Living

Beyond its core heating and cooling functions, the Sharp BU Triple Zone Heat Pump integrates several advanced features that make it a standout choice for any home:

  • Plasmacluster Ion Technology: Exclusive to Sharp, this technology actively works to purify indoor air, neutralizing allergens, bacteria, and viruses, ensuring a healthier living environment.
  • Self-Cleaning Function: The self-cleaning feature prevents mold growth, ensuring the indoor units remain efficient and free from contaminants, reducing maintenance needs.
  • Hot Gas Pipe System: Designed to operate efficiently in extreme cold, the system uses residual heat from defrosting to prevent ice buildup on the outdoor unit, ensuring uninterrupted operation even in the harshest winter conditions.

Grants and Financial Benefits

The financial benefits of this installation were equally impressive. Thanks to the Hydro-Québec LogisVert program, the homeowners were eligible for a $3,000 provincial rebate. In addition, they could apply for a federal grant of up to $5,000, making the Sharp BU Triple Zone Heat Pump not only an energy-efficient choice but also an affordable investment in their home’s comfort.

Why Choose AirGreen?

At AirGreen, we don’t just install HVAC systems—we provide customized solutions tailored to the unique needs of each customer. Our team of experienced professionals ensures that every installation is completed to the highest standards of quality, and we stand by our work with a 10-year warranty on the compressor, parts, and labor. We understand that home comfort is a long-term investment, and we’re here to make sure it’s a stress-free experience for our clients.

If you’re looking for a reliable, energy-efficient heat pump system that can handle the demands of Montreal’s climate, look no further than the Sharp BU Triple Zone Heat Pump. Contact us today to learn more about how we can help you optimize your home’s comfort and reduce your energy bills.

Key Features of the Sharp BU Triple Zone Heat Pump:

  • Energy Star® Certified for maximum efficiency.
  • SEER 24.0 for superior energy savings.
  • R-32 refrigerant for a lower environmental impact.
  • Triple Zone operation, allowing for independent temperature control in three different areas of the home.
  • Plasmacluster Ion Technology for enhanced indoor air quality.
  • Self-cleaning function for mold prevention and reduced maintenance.
  • Hot Gas Pipe System for reliable heating even in temperatures as low as -27°C.
  • WiFi-enabled for remote control and monitoring.

Conclusion

The Sharp BU Triple Zone Heat Pump installed by AirGreen in the North Shore is a powerful, efficient, and sustainable solution for homes looking to optimize both heating and cooling. With advanced technology like Plasmacluster Ionization and the Hot Gas Pipe System, this heat pump is designed to keep your home comfortable year-round, no matter the weather. Combine that with the substantial rebates available, and it’s clear why this installation was such a success. At AirGreen, we are proud to continue offering top-of-the-line HVAC solutions that meet the needs of today’s eco-conscious homeowners.

The unit

The unit on this job, in figures

The range as published on airgreen.ca: pick a size to see its capacity in deep cold.

The range, size by size
SizeHeating at −8 °CHeating at −15 °CColdest certified pointCOP at −15 °CSEERHSPFIndicative LogisVert aid
Sharp BU 24 0002 Zones (Dual Zone)25,00021,200−27 °C: 14,6002.324.011.5$3,000
Sharp BU 24 0003 Zones (Triple Zone)25,00021,200−27 °C: 14,6002.324.011.5$3,000
Most EfficientENERGY STAR

Among the year’s most efficient according to ENERGY STAR, on top of its cold-climate certification.

8,800BTU/h at low speed

Minimum certified capacity (NEEP): it slows down instead of stopping when a single room calls.

−27 °CColdest certified point

NEEP still lists 14,600 BTU/h at a COP of 1.84 at −17 °F.

675R-32 GWP

Global warming potential of R-32, versus 2,088 for R-410A (ENERGY STAR).

Data read live from the airgreen.ca page of each size (NEEP / AHRI certified performance). When the title names the installed size, it is highlighted; otherwise the whole range is shown. The aid shown is today’s, using Hydro-Québec’s rule ($120 per 1,000 BTU/h at −8 °C); amounts quoted in the article date from its publication. Only Hydro-Québec confirms the assistance granted.

The steps

The big day, step by step

The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.

Step 1 of 9The on-site estimate

We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.

  1. The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
  2. The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
  3. Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
  4. The wall openingA single opening, with the slope the drain needs to flow outside.
  5. The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
  6. Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
  7. The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
  8. Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
  9. The walkthroughRemote, modes, filters: we show you the essentials before we leave.
Your numbers

What would it look like at your place?

Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.

Before / afterThe cost of the same heat

Baseboards and electric furnaces turn 1 kWh of electricity into 1 kWh of heat. A heat pump delivers more: that is its COP. At Hydro-Québec’s rate D (11.142¢/kWh above 40 kWh a day, since 1 April 2026):

Before · baseboards11.142¢/kWh
After · heat pump–

Hydro-Québec: a heat pump can be up to three times more efficient than baseboards for heating in the colder months.

Estimate per kWh of heat, at the chosen temperature, using the certified COP from the product page. Taxes, access charge and backup heat not included.

Size checkYour baseboards, in BTU/h
–BTU/h of installed electric heat

    Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.

    Mistakes avoided

    Four mistakes we do not make

    Flip each card to see what we do instead.

    Going further

    Your own project, step by step

    Through the seasons

    What to do, season by season

    Three habits per season for this unit. They take a few minutes and prevent many calls.

    • Clean the indoor unit's filters.
    • Clear leaves and debris left on the outdoor unit by winter.
    • Test cooling before the first hot days.
    At your place

    Is your home ready?

    Check what applies at your place. A "no" is not a refusal: it is what we sort out during the estimate.

    0 / 6 checked
    True or false

    Four statements: true or false?

    It all comes down to details you have just seen.

    1. In heating mode, the outdoor unit can produce water.

    2. You pick the capacity with a simple square-footage rule.

    3. A multi-zone connects several indoor heads to a single condenser.

    4. The disconnect can sit behind the patio furniture.

    Frequently asked questions

    What people ask us about this kind of work

    12 questions
    Does a wall-mounted heat pump heat in winter?
    Yes, it heats and cools. Its capacity drops in very cold weather; the operating range depends on the model and is listed on its spec sheet.
    Wall-mounted or multi-zone: how do I choose?
    One wall head and one condenser outside: the direct solution for a room or an open area. For two to five rooms, a multi-zone puts one head in each room on a single condenser.
    Where does the outdoor unit go?
    Where it stays above the snow, clear and accessible, away from walkways. We decide it with you during the estimate.
    Are there grants?
    Depending on the model and your situation, assistance programs may apply, including Hydro-Québec's LogisVert. AirGreen checks the model number before quoting an amount. See the grants.
    Do I need a permit?
    Rules vary from city to city: location, distances, noise. See permits and by-laws, and we check for your address.
    How cold can it heat?
    It depends on the model. According to Hydro-Québec, newer models work down to a temperature between −15 °C and −25 °C, and some cold-climate models are certified lower. The minimum temperature is on each unit's spec sheet.
    How much can I save?
    Hydro-Québec says a heat pump can be up to three times more efficient than baseboards for heating in the colder months. The result depends on the house, the climate and how it is used.
    How is the LogisVert assistance calculated?
    For ENERGY STAR cold-climate certified heat pumps, Hydro-Québec lists assistance of $120 per 1,000 BTU/h of heating capacity at −8 °C. AirGreen checks the exact model before quoting an amount; only Hydro-Québec confirms the assistance granted. See the grants.
    Is it noisy?
    The sound level depends on the model and is listed in decibels on each unit's spec sheet. Location matters too: when possible, we avoid putting the outdoor unit under a bedroom window.
    The outdoor unit is covered in ice: is that normal?
    Some frost is: the unit runs defrost cycles. Never hit the ice. If the unit stays iced up or stops heating, call us.
    Does AirGreen hold the required licences?
    Yes. AirGreen holds RBQ licence 5645-9605-01, subclasses 15.8 Ventilation, 15.10 Refrigeration and 16 Electricity.
    Is the estimate free?
    Yes. The on-site estimate is free and the quote follows within 24 hours. Book my free estimate.

    Could this job help a neighbour?

    Share
    Similar projects

    More jobs to see, near you

    By town, by equipment or by region: browse more than 4,700 published projects.

    Each dot: a town where AirGreen has published projects. The glowing dot: this job.

    All our projects

    Your project

    Every house has its constraints. We see them before we install.

    The on-site estimate is free and the quote follows within 24 hours.

    • RBQ licence5645-9605-01 · 15.8, 15.10, 16
    • EstimateOn site, free
    • QuoteWithin 24 hours

    Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).

    Leave a comment