A high-performance and elegant solution to enhance living room comfort in Laval
Professional installation in Laval of a SHARP ZU1 15000 BTU wall-mounted heat pump. The perfect HVAC solution to optimize comfort, energy savings, and air quality thanks to advanced Plasmacluster technology.

In summer, the outdoor unit rejects the house's heat outside.
Generic illustration of this type of installation, not a survey of this job site. Tap a number.
Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.
The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.
Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.
A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.
The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.
On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.
The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.
In a charming bungalow located in a quiet, tree-lined neighborhood of Laval, our team recently completed the installation of a SHARP ZU1 15000 BTU wall-mounted heat pump. At AirGreen, every project is an opportunity to transform a living space through heating, ventilation, and air conditioning (HVAC) technology that is reliable, quiet, and energy efficient. And this installation, while visually discreet, stands out for its year-round performance.
A smart choice for year-round comfort
Our clients—a retired couple—wanted to replace their outdated wall-mounted air conditioner that could no longer meet today’s standards. Their priorities: an energy-efficient solution, one that performs in cold winters and actively purifies indoor air. After an on-site technical evaluation, we recommended the SHARP ZU1 15000 BTU wall-mounted heat pump, a high-performing model well-suited for the Québec climate and particularly popular in Laval, Montréal, and the North Shore.
Why the SHARP ZU1 15000 BTU?
Here are the key features of this model that led to our recommendation:
-
Heating capacity up to 18,000 BTU/h and cooling up to 17,000 BTU/h, perfect for a medium-sized living room or open space.
-
Operates efficiently down to -27°C, thanks to SHARP’s patented “Hot Gas Pipe” technology that prevents freezing of the outdoor unit.
-
Uses R32 refrigerant, environmentally friendly, with a 68% lower global warming potential than R-410A.
-
Built-in Plasmacluster technology: actively purifies indoor air by neutralizing mold, viruses, bacteria, and odors.
-
SEER rating of 24, HSPF of 11.8, delivering superior energy efficiency.
-
Sleek, compact, and quiet design, with indoor noise levels as low as 26 dB.
-
Smart connectivity with integrated Wi-Fi, compatible with Google Assistant and Alexa.
A precise and aesthetic installation by AirGreen
The installation process was carefully planned. Here's an overview of the key steps of our intervention:
Initial inspection and planning
First, our technician assessed the space layout: walls, openings, insulation, and electrical panel location. Since the area to condition was a spacious, light-filled living room, it was essential to avoid direct airflow on occupants while maximizing warm or cool air distribution.
Wall mounting and drilling
The indoor unit was installed above a large art canvas, at an optimized height to allow for the Coanda effect, where air flows smoothly along surfaces. This strategic positioning ensures even heating and cooling, without direct drafts.
Drilling to the exterior was done at a precise angle to ensure natural drainage of condensation, avoiding backflow or mold growth.
Connecting the outdoor unit
The outdoor unit was installed on a wall-mounted anti-vibration bracket at the back of the house. This setup offers better protection from snow buildup while reducing noise. We used 1/4 x 3/8 inch insulated piping, compliant with SHARP specifications and within the maximum allowed length of 20 meters.
Commissioning and checks
Once all connections were sealed and insulated, we performed a leak test, followed by nitrogen pressure testing and vacuum pull-down. The heat pump was then activated and tested in cooling and heating modes, verifying pressure levels, temperature output, and airflow. Everything was confirmed to meet SHARP’s standards.
Air purification you can feel—and breathe
This SHARP ZU1 model goes far beyond temperature control. With built-in Plasmacluster technology, it continuously purifies the air. This technology emits positive and negative ions that:
-
Eliminate allergens like dust mites and pollen
-
Neutralize odors from cooking or tobacco
-
Suppress airborne mold and viruses
-
Improve indoor air quality, especially for people with asthma or sensitivities
Our clients have already told us they feel the air is lighter and fresher, just hours after installation.
Eligibility for grants and long-term energy savings
Great news for homeowners in Laval and on the South Shore: this installation qualifies for Hydro-Québec’s LogisVert program, offering up to $2,172 in rebates, depending on eligibility and home configuration. We always guide our clients through the application process to help maximize their return on investment.
Customer testimonial: satisfaction above all
"The AirGreen team was fast, courteous, and above all, very professional. Since the installation, our home feels more comfortable, and we’ve even noticed a drop in our electricity bills. Many thanks!"
— Mrs. L., Laval
Why choose AirGreen for your HVAC installation?
At AirGreen, we don’t just install equipment—we create sustainable, comfortable, and healthy living environments. Here’s what sets us apart:
-
Certified technicians, trained specifically for SHARP models
-
Personalized guidance for equipment selection and available rebates
-
Full transparency on costs, timelines, and warranties
-
Hundreds of successful installations across Greater Montréal
Practical tips before installing a wall-mounted heat pump
-
Properly size the unit for the room: An undersized unit will underperform, while an oversized unit will waste energy.
-
Place the indoor unit wisely to avoid direct airflow and promote circulation.
-
Ensure the outdoor unit stays clear in winter, away from gutters and snow accumulation areas.
-
Choose a certified installer, like AirGreen, to guarantee standards compliance and top performance.
Conclusion: A tailored installation designed for comfort and efficiency in Laval
This SHARP ZU1 15000 BTU wall-mounted heat pump installed in Laval is much more than just a heating or cooling appliance. It represents a smart investment that combines Japanese technology, environmental care, air purification, and long-term savings.
At AirGreen, we take pride in delivering installations that combine performance, durability, and style, while always ensuring our clients’ complete satisfaction.
How it goes, from the first call to the end
The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.
We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
Model, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
Floors and furniture protected, wall plate position marked level, wall opening located.
A single opening, with the slope the drain needs to flow outside.
Set on a stand raised above the snow, with the clearances the manufacturer requires.
Connected, insulated and protected. The opening is then sealed against water, cold air and insects.
A dedicated circuit and an accessible disconnect near the outdoor unit.
Leak test, vacuum, then start-up and a check of heating and cooling.
Remote, modes, filters: we show you the essentials before we leave.
- The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
- The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
- Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
- The wall openingA single opening, with the slope the drain needs to flow outside.
- The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
- Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
- The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
- Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
- The walkthroughRemote, modes, filters: we show you the essentials before we leave.
And at your place?
Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.
Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.
What to do, season by season
Three habits per season for this unit. They take a few minutes and prevent many calls.
- Clean the indoor unit's filters.
- Clear leaves and debris left on the outdoor unit by winter.
- Test cooling before the first hot days.
- Clean the filters more often when the unit runs a lot.
- Keep plants away from the outdoor unit.
- Check that no water drips from the indoor unit.
- Rake the leaves around the outdoor unit.
- Test heating before the first cold days.
- Book periodic maintenance before winter.
- Keep snow away from the stand and the front of the unit.
- Let the unit defrost: it is normal.
- Never hit the ice on the fins; call us if the unit stays iced up.
Which type of equipment for your project?
Pick what looks like your need.
Four mistakes we do not make
Flip each card to see what we do instead.
What people ask us about this kind of work
Does a wall-mounted heat pump heat in winter?
Wall-mounted or multi-zone: how do I choose?
Where does the outdoor unit go?
Are there grants?
Do I need a permit?
How cold can it heat?
How much can I save?
How is the LogisVert assistance calculated?
Is it noisy?
The outdoor unit is covered in ice: is that normal?
Does AirGreen hold the required licences?
Is the estimate free?
No question matches. Write to us: we answer.
Useful pages for what comes next
More jobs to see, near you
By town, by equipment or by region: browse more than 4,700 published projects.
Each dot: a town where AirGreen has published projects. The glowing dot: this job.
Tell us about your house. We come and see it for free.
The on-site estimate is free and the quote follows within 24 hours.
Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).
