Why Is Your New Wall-Mounted Heat Pump Breaking Down Regularly? Answers from Québec Experts
The signs described in this article
Is it urgent?
Tick what you notice at home. This does not replace a diagnosis.
Your result appears here.
Understanding the Most Common Causes of Frequent Breakdowns in New Wall-Mounted Heat Pumps in Québec
At AirGreen, we’ve been getting more and more calls from customers who’ve had a new wall-mounted heat pump installed by other companies, only to find themselves facing recurring breakdowns just months after startup. In this article, we share our on-site analysis, based on dozens of real cases in Montréal, Laval, Longueuil, the North Shore, and the South Shore, to help you understand the real reasons behind these problems—and more importantly, how to avoid them.
Poor Installation: The Number One Cause of Early Breakdowns
In over 70% of the cases we handle, the main issue isn’t the unit itself, but the installation. A poorly installed heat pump—even a high-end model—is destined to fail.
The most common errors:
-
Poorly insulated piping, causing thermal loss.
-
Incorrect condensate drainage, leading to water leaks inside.
-
Improper electrical connection, exposing the unit to power surges.
-
Incorrect orientation or installation height, which hinders airflow.
A real example in Boisbriand: a customer contacted us about a Gree Sapphire 18,000 BTU heat pump installed by another company. Result: three breakdowns in two months. After inspection, we discovered oversized wiring, a poorly tilted indoor unit, and no insulation on the exterior piping. Once we corrected the issues, the unit has worked flawlessly.
Mishandling During Installation: Details Matter
A wall-mounted heat pump is a delicate system, and its components must be handled with precision. Too often, inexperienced technicians make irreversible mistakes during installation:
-
Overtightening of fittings, causing micro refrigerant leaks.
-
Skipping the leak test, leading to invisible refrigerant loss.
-
Startup without proper vacuuming, leaving moisture in the lines and damaging the compressor.
At AirGreen, we follow a strict protocol:
-
Nitrogen pressure test.
-
Minimum 30-minute vacuum cycle.
-
Measurement of pressure and temperature before startup.
Choosing the Wrong Model: Not All Units Are Built for Québec Winters
Some units sold in Québec are not designed to handle our harsh winters. They often break down when pushed to -15 °C or -20 °C. Many customers think they’re getting a great deal with low-cost imported models, but those units are rarely optimized for the Québec climate.
Our AirGreen recommendations:
-
Always choose a model rated for -25 °C or -30 °C.
-
Check the SEER and HSPF, but also cold-weather performance stability.
-
Choose proven brands like Fujitsu, Gree, Sharp, or Midea, with robust parts and strong local support.
Neglected Maintenance During the First Year: A Common Mistake
Even a new heat pump can break down if it’s not maintained during the first season. Many customers mistakenly believe that a new unit requires no maintenance. In reality:
-
Filters can get clogged in under 3 months.
-
Dust or insects can block the drain.
-
Moisture buildup can cause corrosion on electronic components.
Our advice: schedule an inspection and cleaning before winter, even if your unit was just installed. This helps catch minor issues before they become major failures.
Improper Sizing: When the Unit Is Too Small… or Too Big
Sizing is everything. An oversized heat pump will constantly turn on and off (a phenomenon known as short cycling), reducing its lifespan. An undersized unit, on the other hand, will run non-stop and still never reach the desired temperature.
At AirGreen, we use precise calculation tools that consider:
-
The actual square footage to heat or cool.
-
The level of insulation, window surfaces, and sun exposure.
-
The number of occupants and specific layout uses (e.g., open kitchen, mezzanine).
Testimonial: Emergency Call in Longueuil After Three Breakdowns on a New Unit
Ms. L. contacted us after her Sharp ZU1 12,000 BTU wall-mounted heat pump broke down three times in six months. Installed in a top-floor condo, the outdoor unit was fully exposed to dominant winds. Result: overheating and repeated compressor shutdowns.
Our solutions:
-
Built a custom wind shield around the outdoor unit.
-
Relocated the indoor unit to improve air distribution.
-
Complete inspection of the refrigerant circuit.
Since our intervention, there have been zero breakdowns.
What Makes AirGreen Different
Here’s why our installations don’t break down regularly:
-
Free on-site evaluation before any quote.
-
Certified technicians with a minimum of 5 years of HVAC experience.
-
High-quality materials, with CSA-certified accessories.
-
Guided commissioning process, with a detailed technical report.
-
Responsive after-sales service, with follow-ups at 1, 6, and 12 months.
We believe that a properly installed wall-mounted heat pump should last over 15 years without major issues.
Conclusion: How to Prevent Recurring Breakdowns
If your new wall-mounted heat pump keeps breaking down, here’s what we recommend:
-
Get the installation inspected by a qualified professional.
-
Review the brand, model, and technical specifications.
-
Schedule annual maintenance, even in the first year.
-
Be cautious of very low quotes: the upfront price doesn’t reflect installation quality.
At AirGreen, we put our experience to work for your comfort in Montréal, Laval, Longueuil, the South Shore, and the North Shore. Don’t wait for another breakdown—contact us for an honest and accurate assessment.
From reading to your home.
An AirGreen advisor assesses your situation on site, free of charge, and gives you a quote within 24 hours.
- RBQ licence 5645-9605-01Subclasses 15.8, 15.10 and 16
- Free on-site estimateAn advisor assesses your needs
- Quote within 24 hoursClear and detailed



