EMERSON Classic 80 Series 1F86-344 Thermostat | Montreal, Laval, Longueuil, South Shore & North Shore
Air conditioning in May, heat again in October: the Classic 80 1F86-344 keeps a separate setpoint for each mode and reminds you to check the filter.
Quick facts
Every spring you switch from heating to cooling, every fall you switch back, and with an ordinary thermostat you have to adjust the setpoint each time. The Classic 80 Series 1F86-344 (the White-Rodgers line from EMERSON) keeps a separate heating setpoint and cooling setpoint, and it reminds you when to check the filter. It is non-programmable, so there is no schedule to enter.
Two setpoints, a filter reminder, no schedule
- Separate setpoints: one for heating, one for cooling.
- Filter reminder: so the filter change does not slip by.
- Non-programmable: the temperature stays where you set it.
- Backlit LCD: readable in a dim hallway.
- Slim housing: 6.1 in. wide, 3.8 in. high and 1.1 in. deep.
- Terminals: RC, RH, C, W, Y, G, O and B, on batteries or hardwired.
Equipment it can control
The 1F86-344 controls one heating stage and one cooling stage: a gas, oil or electric furnace, a millivolt system, or a single-stage heat pump without backup heat. The Classic 80 instructions also list hot water or steam systems, except 3-wire zoned hydronic systems. It does not suit dual fuel, baseboards, electric floor heating, fan-forced heaters or wall or ducted heat pumps.
The 80 Series model and the programmable sibling
In its 2025 cross-reference table, the brand lists the EMERSON 80 Series 1F83C-11NP to replace the 1F86-344. Also non-programmable, it takes setpoints up to 37 °C; its sheet lists a 1.5 A per-terminal rating and a high-contrast backlit display, and it names gas, oil, electric and millivolt systems, with no mention of hot water or steam. From the same Classic 80 series, the EMERSON Classic 80 Series 1F80-361 runs a 5-1-1 schedule and stores its heating and cooling programs at the same time.
On site with AirGreen
The 1F86-344 runs on batteries or hardwired, and we pick based on the wiring behind your old thermostat. On a furnace or heat pump, we connect the RC and RH terminals as your equipment requires, then enter your two setpoints with you. The starting point is a free in-home estimate.
Manufacturer document: 1F86-344 page on the brand’s website. Sold and installed by AirGreen. We serve Montréal, Laval, Longueuil, the North Shore and the South Shore.
Key facts: EMERSON Classic 80 Series 1F86-344
Four things to know, then its ID card in twelve answers. “—” means the manufacturer does not publish it.
Is the EMERSON Classic 80 Series 1F86-344 compatible with your heating?
Two steps, thirty seconds. The verdict takes your system and your wiring into account.
Full compatibility table
The terminals behind the thermostat
Tap an element to see what it does. A working diagram, not a substitute for the manufacturer’s installation guide.
Try the EMERSON Classic 80 Series 1F86-344 before you buy
Raise the setpoint, change the mode: see how it responds.
Winter, Rate Flex D and rebates: what this thermostat changes
With Hydro-Québec’s Rate Flex D, electricity costs less most of the winter and more during a few peak hours. Turning the setpoint down a few degrees during those hours is what counts.
The EMERSON Classic 80 Series 1F86-344 or its closest sibling?
The most useful comparison: the model right next to it in our catalogue.
The right thermostat in three questions
If this model is not the right one for you, the page says so and shows you which one is.
Installed and set up by our technicians, in five steps
What we do at your place, in order. The on-site estimate is free.
- 01InspectionEquipment, stages to control and existing wiring.
- 02C wireCommon wire added if the model needs it and it is missing.
- 03MountingWall base, terminal wiring, cover plate if needed.
- 04SettingsEquipment type, stages, dual energy and accessories.
- 05Start-upConnection, app, schedule and tests with you.
EMERSON Classic 80 Series 1F86-344 specifications
From the manufacturer’s sheet. Type a word: the list filters as you write.
No line matches. Try another word.
Frequently asked questions about the EMERSON Classic 80 Series 1F86-344
Short answers, no detours.
What does the EMERSON Classic 80 Series 1F86-344 work with?
According to the manufacturer’s sheet: gas, oil or electric; millivolt; hot water or steam; single-stage heat pump with no backup heat.
Does it need a C wire?
Per the spec sheet, it can run on batteries; a common wire is still recommended when available.
Can it control electric baseboards?
No. It is a low-voltage (24 V) thermostat. 120/240 V baseboards need a line-voltage electronic thermostat.
Can it be controlled remotely?
Not directly: it has no built-in Wi-Fi.
Does AirGreen install it?
Yes. We sell and install this product in Montréal, Laval, Longueuil, the South Shore and the North Shore. The on-site estimate is free.
No question matches. Call us at 514 316-2973.
Your thermostat, installed and set up by our technicians
We check your system and wiring, install the thermostat, connect it and program it with you. One visit, one installed price.
