Home » AirGreen's Outstanding HVAC Projects in Greater Montreal, Laval, Longueuil, South Shore and North Shore » Installation of a Sharp Eco Inverter wall-mounted heat pump in Villeray–Saint-Michel–Parc-Extension
Project

Installation of a Sharp Eco Inverter wall-mounted heat pump in Villeray–Saint-Michel–Parc-Extension

AirGreen installed a Sharp Eco Inverter wall-mounted heat pump in Villeray–Saint-Michel–Parc-Extension. A high-performance and aesthetic HVAC solution for four-season comfort in Montreal.

By AirGreen Climatisation & Chauffage Admin3 min read
Installation of a Sharp Eco Inverter wall-mounted heat pump in Villeray–Saint-Michel–Parc-Extension
Installation of a Sharp Eco Inverter wall-mounted heat pump in Villeray–Saint-Michel–Parc-Extension
Generic diagram: wall-mounted heat pump, indoor and outdoor units

In summer, the outdoor unit rejects the house's heat outside.

Generic illustration of this type of installation, not a survey of this job site. Tap a number.

  1. Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.

  2. The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.

  3. Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.

  4. A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.

  5. The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.

  6. On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.

  7. The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.

An HVAC solution adapted to Montreal brick plexes

In a residential area of ​​Villeray–Saint-Michel–Parc-Extension , our AirGreen team recently completed the installation of a Sharp Eco Inverter wall-mounted heat pump . The building, a typical Montreal red brick duplex, presented a classic installation context but required special attention to the choice of support and the management of refrigeration connections.

Context and customer choice

The owner was looking for a versatile system to provide efficient heating in winter and comfortable cooling in summer , while enjoying better energy performance. The Sharp Eco Inverter range offers an optimal balance of efficiency, durability and quiet operation, all with the exclusive Plasmacluster technology, which improves indoor air quality.

Technical specifications of the installation

  • Device type : wall-mounted heat pump (mini-split).

  • Make and model : Sharp Eco Inverter with Plasmacluster technology.

  • Typical capacity : 12,000 BTU, suitable for a home of approximately 1,000 sq ft.

  • Condenser location : fixed to the exterior brick wall, approximately 1.2 m from the ground.

  • Support used : reinforced galvanized wall brackets, allowing optimal clearance from the ground to prevent snow accumulation and ensure air circulation.

  • Refrigeration connections : protected by discreet external capping, ensuring protection against bad weather and a neat finish.

  • Condensate drainage : gravity system, adapted to the installation height.

Challenges and solutions provided

  1. Solid brick walls :
    Drilling into an old brick wall requires precision and specialized equipment to prevent cracking. Our technicians used sturdy anchors to ensure a lasting hold.

  2. Facade aesthetics :
    The owner wanted to minimize the visual impact of the installation. We opted for capping that matched the facade , ensuring both protection and discretion.

  3. Winter performance :
    Given that Montreal experiences harsh winters, we took care to install the unit at a sufficient height to avoid any obstruction by snow and to facilitate automatic defrosting.

Benefits for the customer

  • Year-round comfort : efficient heating down to sub-zero temperatures and effective air conditioning during summer heat waves.

  • Healthier air : thanks to Plasmacluster technology, which reduces suspended particles and improves air quality.

  • Energy savings : an inverter device that modulates its power to reduce electricity consumption.

  • Simplified maintenance : installation designed for easy access during annual maintenance visits.

AirGreen expertise in Montreal

Every building in Greater Montreal has its own unique challenges. In this Villeray–Saint-Michel–Parc-Extension project, our team demonstrated its expertise in HVAC installation on brick facades. Through rigorous preparation, the use of quality materials, and meticulous workmanship, we delivered a reliable and aesthetically pleasing installation that perfectly met the client's expectations.

AirGreen: a trusted HVAC partner in Greater Montreal

Whether in Montreal, Laval, Longueuil, on the North Shore or the South Shore, AirGreen assists its clients in the selection, installation, and maintenance of their HVAC systems. Our priority is to offer solutions adapted to each building and each budget, while guaranteeing comfort and energy efficiency.

The steps

How it goes, from the first call to the end

The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.

Step 1 of 9The on-site estimate

We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.

  1. The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
  2. The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
  3. Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
  4. The wall openingA single opening, with the slope the drain needs to flow outside.
  5. The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
  6. Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
  7. The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
  8. Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
  9. The walkthroughRemote, modes, filters: we show you the essentials before we leave.
Your numbers

And at your place?

Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.

Size checkYour baseboards, in BTU/h
–BTU/h of installed electric heat

    Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.

    Through the seasons

    What to do, season by season

    Three habits per season for this unit. They take a few minutes and prevent many calls.

    • Clean the indoor unit's filters.
    • Clear leaves and debris left on the outdoor unit by winter.
    • Test cooling before the first hot days.
    And at your place?

    Which type of equipment for your project?

    Pick what looks like your need.

    Mistakes avoided

    Four mistakes we do not make

    Flip each card to see what we do instead.

    Frequently asked questions

    What people ask us about this kind of work

    12 questions
    Does a wall-mounted heat pump heat in winter?
    Yes, it heats and cools. Its capacity drops in very cold weather; the operating range depends on the model and is listed on its spec sheet.
    Wall-mounted or multi-zone: how do I choose?
    One wall head and one condenser outside: the direct solution for a room or an open area. For two to five rooms, a multi-zone puts one head in each room on a single condenser.
    Where does the outdoor unit go?
    Where it stays above the snow, clear and accessible, away from walkways. We decide it with you during the estimate.
    Are there grants?
    Depending on the model and your situation, assistance programs may apply, including Hydro-Québec's LogisVert. AirGreen checks the model number before quoting an amount. See the grants.
    Do I need a permit?
    Rules vary from city to city: location, distances, noise. See permits and by-laws, and we check for your address.
    How cold can it heat?
    It depends on the model. According to Hydro-Québec, newer models work down to a temperature between −15 °C and −25 °C, and some cold-climate models are certified lower. The minimum temperature is on each unit's spec sheet.
    How much can I save?
    Hydro-Québec says a heat pump can be up to three times more efficient than baseboards for heating in the colder months. The result depends on the house, the climate and how it is used.
    How is the LogisVert assistance calculated?
    For ENERGY STAR cold-climate certified heat pumps, Hydro-Québec lists assistance of $120 per 1,000 BTU/h of heating capacity at −8 °C. AirGreen checks the exact model before quoting an amount; only Hydro-Québec confirms the assistance granted. See the grants.
    Is it noisy?
    The sound level depends on the model and is listed in decibels on each unit's spec sheet. Location matters too: when possible, we avoid putting the outdoor unit under a bedroom window.
    The outdoor unit is covered in ice: is that normal?
    Some frost is: the unit runs defrost cycles. Never hit the ice. If the unit stays iced up or stops heating, call us.
    Does AirGreen hold the required licences?
    Yes. AirGreen holds RBQ licence 5645-9605-01, subclasses 15.8 Ventilation, 15.10 Refrigeration and 16 Electricity.
    Is the estimate free?
    Yes. The on-site estimate is free and the quote follows within 24 hours. Book my free estimate.
    Going further

    Useful pages for what comes next

    GrantsAssistance programs in effectAirGreen checks your model before quoting an amount.PermitsYour city’s rulesLocation, distances, noise: what changes from city to city.InstallationOur installation serviceGreater Montréal and Montérégie.

    Could this job help a neighbour?

    Share
    Similar projects

    More jobs to see, near you

    By town, by equipment or by region: browse more than 4,700 published projects.

    Each dot: a town where AirGreen has published projects. The glowing dot: this job.

    All our projects

    Your project

    Tell us about your house. We come and see it for free.

    The on-site estimate is free and the quote follows within 24 hours.

    Book my free estimate514 316-2973
    • RBQ licence5645-9605-01 · 15.8, 15.10, 16
    • EstimateOn site, free
    • QuoteWithin 24 hours

    Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).

    Leave a comment