Installation of a Canair wall-mounted heat pump in Ville-Marie (Montreal)
AirGreen installed a Canair wall-mounted heat pump in a condo in Ville-Marie, Montreal. The elegant indoor unit, ideally positioned near the ceiling, provides year-round comfort thanks to stable and quiet air distribution.
In summer, the outdoor unit rejects the house's heat outside.
Generic illustration of this type of installation, not a survey of this job site. Tap a number.
Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.
The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.
Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.
A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.
The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.
On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.
The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.
In a condo in Ville-Marie , we installed a Canair wall-mounted heat pump (mini-split) , a popular solution in Montreal for combining efficient air conditioning in the summer with comfortable supplemental heating during colder periods. The photo clearly shows the indoor wall unit: a sleek design, installed high up, discreet, and perfectly integrated into the decor.
A logical choice for a Montreal condo
Condos in downtown Montreal often require quiet , compact , and aesthetically pleasing systems. A wall-mounted unit like this one perfectly meets these requirements:
-
No additional ventilation ductwork required (ideal when space is optimized)
-
Rapid comfort : air is distributed evenly throughout the room
-
Precise control : stable temperature, improved everyday comfort
-
Very low noise level : a crucial point for a bedroom, office, or open-plan living room
Type of machine installed
This is a Canair wall-mounted heat pump (indoor unit). The exact model is not visible in the photo, but the setup corresponds to a typical "new generation" residential configuration: a modern wall head, designed to offer good airflow with smooth and stable operation.
At AirGreen, when the model is not shown directly in the photo, we deliberately remain cautious: the important thing is to remember the type of system (wall-mounted) and the brand (Canair), then to describe the actual installation and its concrete benefits.
Visible installation details and key technical points
Several elements visually stand out in this installation and reflect a clean, compliant, and comfort-oriented execution:
-
Positioning high up, near the ceiling : excellent for air circulation and even temperature distribution.
-
Careful alignment : the unit is placed upright, with the correct clearance, to avoid turbulence and discomfort.
-
Discreet integration : minimal visual impact, minimalist style, perfect for a modern interior.
-
Diffusion flap : allows you to direct the air to avoid “direct blowing” on the occupants (particularly important in small rooms).
Behind this seemingly “simple” result, there is a series of important decisions: choice of location (load-bearing wall / passage areas), management of the routing of connections, optimization of comfort (height, flow orientation, distance from rest areas), and preparation for easy maintenance.
Everyday comfort: what the customer actually gains
A properly installed wall-mounted heat pump isn't just about "cool air in the summer." It's about consistent, healthier, and more stable comfort .
-
Rapid cooling during heat and humidity episodes in Montreal
-
An effective supplementary heater in mid-season (spring/autumn), and very practical for reducing the feeling of "damp cold"
-
Fewer temperature fluctuations : the room becomes more pleasant, morning and evening.
-
Improved zone management : the main zone (living room, bedroom, office) is precisely controlled.
Why installation is just as important as the brand
Even an excellent machine can disappoint if the installation is botched. At AirGreen, our priority is that the system works as intended , for a long time, with stable performance. A successful installation means:
-
a location that promotes performance (and not just “the easiest place”)
-
a clean and durable assembly
-
an aesthetic result, especially in a condo
-
immediate comfort, without any harsh drafts
The goal: for the Canair wall-mounted heat pump to become an “invisible” piece of equipment in everyday life — you only notice it because you feel good.
AirGreen: a simple, professional, and results-oriented approach
For each residential installation in Greater Montreal, we maintain the same method: assess the location , choose the right positioning , aim for a clean integration and ensure optimal operation from the moment of commissioning.
This installation in Ville-Marie perfectly illustrates what we are looking for: a discreet finish, efficient air diffusion, and a comfort solution adapted to the reality of Montreal condos.
How it goes, from the first call to the end
The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.
We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
Model, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
Floors and furniture protected, wall plate position marked level, wall opening located.
A single opening, with the slope the drain needs to flow outside.
Set on a stand raised above the snow, with the clearances the manufacturer requires.
Connected, insulated and protected. The opening is then sealed against water, cold air and insects.
A dedicated circuit and an accessible disconnect near the outdoor unit.
Leak test, vacuum, then start-up and a check of heating and cooling.
Remote, modes, filters: we show you the essentials before we leave.
- The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
- The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
- Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
- The wall openingA single opening, with the slope the drain needs to flow outside.
- The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
- Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
- The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
- Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
- The walkthroughRemote, modes, filters: we show you the essentials before we leave.
And at your place?
Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.
Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.
What to do, season by season
Three habits per season for this unit. They take a few minutes and prevent many calls.
- Clean the indoor unit's filters.
- Clear leaves and debris left on the outdoor unit by winter.
- Test cooling before the first hot days.
- Clean the filters more often when the unit runs a lot.
- Keep plants away from the outdoor unit.
- Check that no water drips from the indoor unit.
- Rake the leaves around the outdoor unit.
- Test heating before the first cold days.
- Book periodic maintenance before winter.
- Keep snow away from the stand and the front of the unit.
- Let the unit defrost: it is normal.
- Never hit the ice on the fins; call us if the unit stays iced up.
Which type of equipment for your project?
Pick what looks like your need.
Four mistakes we do not make
Flip each card to see what we do instead.
What people ask us about this kind of work
Does a wall-mounted heat pump heat in winter?
Wall-mounted or multi-zone: how do I choose?
Where does the outdoor unit go?
Are there grants?
Do I need a permit?
How cold can it heat?
How much can I save?
How is the LogisVert assistance calculated?
Is it noisy?
The outdoor unit is covered in ice: is that normal?
Does AirGreen hold the required licences?
Is the estimate free?
No question matches. Write to us: we answer.
Useful pages for what comes next
More jobs to see, near you
By town, by equipment or by region: browse more than 4,700 published projects.
Each dot: a town where AirGreen has published projects. The glowing dot: this job.
Tell us about your house. We come and see it for free.
The on-site estimate is free and the quote follows within 24 hours.
Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).