Project

Installation of a Fujitsu AIRSTAGE Orion XLTH wall-mounted heat pump in Pointe-des-Cascades

AirGreen installation of a Fujitsu Orion XLTH R-32 in Pointe-des-Cascades, with the outdoor unit on elevated wall brackets to promote clearance, winter operation, and a durable HVAC installation.

By AirGreen Climatisation & Chauffage Admin11 min read
Installation of a Fujitsu AIRSTAGE Orion XLTH wall-mounted heat pump in Pointe-des-Cascades
Installation of a Fujitsu AIRSTAGE Orion XLTH wall-mounted heat pump in Pointe-des-Cascades
Generic diagram: wall-mounted heat pump, indoor and outdoor units

In summer, the outdoor unit rejects the house's heat outside.

Generic illustration of this type of installation, not a survey of this job site. Tap a number.

  1. Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.

  2. The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.

  3. Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.

  4. A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.

  5. The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.

  6. On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.

  7. The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.

A Fujitsu Orion XLTH installation designed for Pointe-des-Cascades winters

In Pointe-des-Cascades, installing a wall-mounted heat pump is not simply a matter of attaching an outdoor unit to a wall and connecting two refrigerant lines. The equipment’s position, snow accumulation, access to the building entrance, proximity to windows, airflow, and exterior finish must all be considered to achieve a durable installation.

For this project, we installed a Fujitsu AIRSTAGE Orion XLTH wall-mounted heat pump, a series specifically designed to provide heating in cold climates. In the photo of this AirGreen installation, one of the most visible elements is the particularly high positioning of the outdoor unit: rather than placing the condenser near the ground, we installed it on a reinforced metal wall structure, directly on the façade.

This choice is particularly relevant in a municipality such as Pointe-des-Cascades, where a heat pump must continue to breathe properly even when snow accumulates around the building.

Fujitsu documentation for the Orion XLTH series indicates a heating operating range down to -26 °C, as well as cooling operation between -10 °C and 50 °C. The entire range also uses R-32 refrigerant.

A high-mounted outdoor unit: a detail that changes a great deal

The building’s layout presented a very practical constraint here: the outdoor unit had to be installed on a relatively narrow section of wall, near an exterior door and a railing, while remaining above the level where snow can accumulate.

We therefore opted for an installation on robust wall brackets, with a structure deep enough to keep the unit well clear of the exterior cladding.

This method offers several advantages:

  • reduced risk of snow blocking the air intake or exhaust;
  • greater clearance beneath the heat pump during defrost cycles;
  • protection against certain accumulations of ice at ground level;
  • maintaining usable space around the entrance;
  • cleaner installation when floor space is limited;
  • more logical access to the lines when they need to reach the inside of the building quickly.

In the photo, we can also see that the condenser is positioned to maintain clearance in front of its fan. This is essential: a heat pump may be technically very high-performing on paper, but poor airflow around the outdoor unit can reduce its performance and complicate operation during the coldest periods.

Why the Fujitsu Orion XLTH is well suited to Quebec’s climate

The Fujitsu AIRSTAGE Orion XLTH belongs to the H-series single-zone wall-mounted system lineup. It combines heating and cooling using a compressor with Inverter technology, which modulates its operation rather than simply alternating between completely off and maximum output.

According to the Fujitsu technical sheet provided for this series, the Orion XLTH models cover several nominal cooling capacities:

  • 9,000 BTU/h;
  • 12,000 BTU/h;
  • 14,500 BTU/h;
  • 18,000 BTU/h;
  • 22,000 BTU/h.

The exact capacity must always be selected based on the building’s actual needs; it cannot be reliably determined simply from a photograph of the outdoor unit.

This is an important distinction when we prepare a heat pump installation in Pointe-des-Cascades, Montreal, Laval, Longueuil, on the North Shore or the South Shore: automatically choosing a larger unit is not necessarily advantageous. Proper sizing helps provide more stable temperatures, better dehumidification in summer, and more consistent Inverter operation.

Low-temperature performance worth analyzing

One noteworthy feature of this series is that it maintains substantial heating capacity as the outdoor temperature drops.

The Fujitsu specification sheet states, among other things, that the models are designed to operate in heating mode down to -26 °C. It also shows the percentages of maximum capacity available at different outdoor temperatures for each capacity.

For example, the 12K model in this series lists:

  • 12,000 BTU/h nominal cooling capacity;
  • 16,000 BTU/h nominal heating capacity;
  • a seasonal efficiency rating of SEER2 30.5;
  • an HSPF2 Region V rating of 10.1;
  • a heating range reaching down to -26 °C;
  • a 15 A circuit breaker according to the specifications for the 12K series.

These figures show why a cold-climate heat pump must be compared based on more than its nominal capacity. For a home located in Pointe-des-Cascades, what really matters in January is not only the number of BTUs stated in the machine's name, but its ability to produce heat when the outdoor temperature drops significantly.

R-32: the new generation of refrigerant used by this series

The logo R32 is also clearly visible on the installed outdoor unit.

Fujitsu states that R-32 has a lower global warming potential than R-410A. In its documentation, the manufacturer indicates a GWP of 675 for R-32 versus 2,088 for R-410A, representing an announced reduction of 68%.

For us, this evolution also means working with procedures, tools, and installation practices suited to the refrigerant specified by the manufacturer. A professional installation must always comply with the specific specifications of the machine being installed.

What this installation in Pointe-des-Cascades concretely shows in the field

The condenser location must be chosen before considering aesthetics

The outdoor unit is located here on a façade covered with horizontal siding, between a large glazed section and an exterior entrance.

This type of location requires several elements to be considered simultaneously.

We must specifically check:

The strength of the support

An outdoor unit should never rely solely on the home's decorative siding. The brackets must be properly secured to a structure that is strong enough to support the weight of the unit as well as the vibrations generated during operation.

Depending on the capacity selected, Fujitsu documentation indicates that Orion XLTH outdoor units can weigh 39 kg (86 lb) for the smaller models in the range or 53 kg (117 lb) for the larger models.

This weight explains why the quality of the anchors is much more important than it may appear from the ground.

Clearance for defrosting

When a heat pump heats a home in cold weather, frost can form on the outdoor coil. The unit periodically runs a defrost cycle.

Water is then produced around and beneath the unit.

A machine installed too close to the ground can gradually become surrounded by ice. By installing the equipment higher, as in this project in Pointe-des-Cascades, we create more space for this water to drain and for the normal accumulation of snow during the winter.

The Orion XLTH series also features a base pan heater designed for regions with extremely cold climates, according to Fujitsu.

A compact heat pump that still requires the proper clearances

The outdoor unit in the lineup retains a relatively compact form. The technical specifications indicate, in particular, an outdoor height of 632 mm, a width of 799 mm, and a depth of approximately 290 mm for the models presented in this series.

This compactness gives us more options when working on:

  • homes with narrow side passages;
  • balconies;
  • facades with limited available space;
  • properties where ground clearance must be maintained;
  • multi-unit residential buildings.

However, compact does not mean that the unit can be installed anywhere. The heat exchanger must always receive sufficient airflow, and the air discharged by the fan must not immediately recirculate back toward the unit.

Piping lengths provide good installation flexibility

Another useful feature of the Orion XLTH lineup is the flexibility provided by its piping lengths.

Depending on the model, Fujitsu specifies maximum lengths ranging from 25 metres (82 ft.) to 50 metres (164 ft.). The maximum allowable vertical difference also varies according to capacity.

This can become important when the ideal indoor unit is far from the best outdoor location.

Piping dimensions also vary according to capacity:

  • 9K and 12K models: 1/4 in. liquid and 3/8 in. gas;
  • 15K model: 1/4 in. liquid and 1/2 in. gas;
  • 18K and 24K models: 3/8 in. liquid and 5/8 in. gas.

That is precisely why we do not treat all wall-mounted installations as interchangeable. The existing piping from an older heat pump cannot automatically be reused simply because it already reaches the right location.

Indoor comfort also depends on sound level

In a bedroom, office, or living area, indoor unit noise is often a major concern.

On the smaller Orion XLTH models, Fujitsu states that indoor sound levels can drop as low as 23 dB(A) in quiet mode. The series offers several fan speeds as well as an automatic setting.

For a homeowner replacing an old wall-mounted air conditioner that operated almost constantly at full power, the difference made by a modern Inverter system can be particularly noticeable: the unit can modulate its output to maintain the requested temperature without unnecessarily multiplying shutdowns and restarts.

Built-in Wi-Fi and remote control

The series documentation also mentions integrated Wi-Fi connectivity, enabling remote monitoring and control through the AIRSTAGE mobile app.

For many homeowners, this feature is more than just a gimmick. It can be useful for:

  • adjust the temperature before returning home;
  • check the heat pump’s operation remotely;
  • change a setting without being in front of the remote control;
  • better manage a residence used intermittently.

A common mistake: choosing the heat pump before choosing its location

We regularly see projects where the owner has already chosen a capacity or model before the installation constraints have even been analyzed.

We proceed in the opposite order.

Before installation, it is important to determine, among other things:

  1. where the indoor unit will be installed;
  2. where the refrigerant lines can run;
  3. how the condensate will be drained;
  4. where the outdoor unit can be installed without blocking a passage;
  5. what height is required for winter;
  6. how to access the equipment for HVAC maintenance;
  7. what electrical power supply is available;
  8. which capacity truly meets the building’s needs.

This Fujitsu Orion XLTH installation in Pointe-des-Cascades illustrates this approach well. The condenser’s height and support structure are not details added as an afterthought: they are an integral part of the installation’s quality.

Our AirGreen approach to installing a Fujitsu wall-mounted heat pump

At AirGreen, we install wall-mounted heat pumps throughout Greater Montreal, including Montreal, Laval, Longueuil, the North Shore and the South Shore, as well as in municipalities such as Pointe-des-Cascades.

Every building has its own constraints.

Some installations require a ground support. Others call for an elevated wall-mounted installation like this one. In some cases, the main challenge is the length of the lines. In others, it involves protecting the condenser from snow accumulation or keeping a clear passage around a balcony.

Our job is to combine the manufacturer’s technical specifications with the building’s physical reality.

A Fujitsu AIRSTAGE Orion XLTH heat pump has features well suited to our climate, but its long-term performance also depends on proper sizing, refrigerant line connections, electrical installation, condensate drainage, and above all, its location.

In Pointe-des-Cascades, this elevated outdoor unit is an excellent example: a compact, securely supported solution designed to allow the machine to breathe and maintain better clearance when the Quebec winter returns.

The steps

How it goes, from the first call to the end

The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.

Step 1 of 9The on-site estimate

We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.

  1. The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
  2. The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
  3. Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
  4. The wall openingA single opening, with the slope the drain needs to flow outside.
  5. The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
  6. Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
  7. The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
  8. Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
  9. The walkthroughRemote, modes, filters: we show you the essentials before we leave.
Your numbers

And at your place?

Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.

Size checkYour baseboards, in BTU/h
–BTU/h of installed electric heat

    Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.

    Through the seasons

    What to do, season by season

    Three habits per season for this unit. They take a few minutes and prevent many calls.

    • Clean the indoor unit's filters.
    • Clear leaves and debris left on the outdoor unit by winter.
    • Test cooling before the first hot days.
    And at your place?

    Which type of equipment for your project?

    Pick what looks like your need.

    Mistakes avoided

    Four mistakes we do not make

    Flip each card to see what we do instead.

    Frequently asked questions

    What people ask us about this kind of work

    12 questions
    Does a wall-mounted heat pump heat in winter?
    Yes, it heats and cools. Its capacity drops in very cold weather; the operating range depends on the model and is listed on its spec sheet.
    Wall-mounted or multi-zone: how do I choose?
    One wall head and one condenser outside: the direct solution for a room or an open area. For two to five rooms, a multi-zone puts one head in each room on a single condenser.
    Where does the outdoor unit go?
    Where it stays above the snow, clear and accessible, away from walkways. We decide it with you during the estimate.
    Are there grants?
    Depending on the model and your situation, assistance programs may apply, including Hydro-Québec's LogisVert. AirGreen checks the model number before quoting an amount. See the grants.
    Do I need a permit?
    Rules vary from city to city: location, distances, noise. See permits and by-laws, and we check for your address.
    How cold can it heat?
    It depends on the model. According to Hydro-Québec, newer models work down to a temperature between −15 °C and −25 °C, and some cold-climate models are certified lower. The minimum temperature is on each unit's spec sheet.
    How much can I save?
    Hydro-Québec says a heat pump can be up to three times more efficient than baseboards for heating in the colder months. The result depends on the house, the climate and how it is used.
    How is the LogisVert assistance calculated?
    For ENERGY STAR cold-climate certified heat pumps, Hydro-Québec lists assistance of $120 per 1,000 BTU/h of heating capacity at −8 °C. AirGreen checks the exact model before quoting an amount; only Hydro-Québec confirms the assistance granted. See the grants.
    Is it noisy?
    The sound level depends on the model and is listed in decibels on each unit's spec sheet. Location matters too: when possible, we avoid putting the outdoor unit under a bedroom window.
    The outdoor unit is covered in ice: is that normal?
    Some frost is: the unit runs defrost cycles. Never hit the ice. If the unit stays iced up or stops heating, call us.
    Does AirGreen hold the required licences?
    Yes. AirGreen holds RBQ licence 5645-9605-01, subclasses 15.8 Ventilation, 15.10 Refrigeration and 16 Electricity.
    Is the estimate free?
    Yes. The on-site estimate is free and the quote follows within 24 hours. Book my free estimate.
    Going further

    Useful pages for what comes next

    Could this job help a neighbour?

    Share
    Similar projects

    More jobs to see, near you

    By town, by equipment or by region: browse more than 4,700 published projects.

    Each dot: a town where AirGreen has published projects. The glowing dot: this job.

    All our projects

    Your project

    Tell us about your house. We come and see it for free.

    The on-site estimate is free and the quote follows within 24 hours.

    • RBQ licence5645-9605-01 · 15.8, 15.10, 16
    • EstimateOn site, free
    • QuoteWithin 24 hours

    Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).

    Leave a comment