Installation of a Sharp wall-mounted heat pump in Rosemont–La Petite-Patrie
In Rosemont–La Petite-Patrie, AirGreen installed a Sharp ZU1 wall-mounted heat pump, perfectly suited to a typical brick house in the neighborhood. The clean, safe, and efficient installation ensures the client's comfort and energy savings year-round.

Take a tour of the installation
Each number is a point we check on site. Switch between summer and winter to watch air and heat move.
In summer, the outdoor unit rejects the house's heat outside.
Generic illustration of this type of installation, not a survey of this job site. Tap a number.
Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.
The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.
Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.
A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.
The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.
On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.
The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.
In Rosemont–La Petite-Patrie, a duplex owner wanted to replace their old air conditioning system with a more efficient heating solution that was quieter and, above all, more economical year-round. Our AirGreen team recommended the installation of aSharp wall-mounted heat pump , a modern inverter system using a low-environmental-impact A2L refrigerant, perfectly suited to Montreal's climate.
A typical side courtyard project in Rosemont
The house is a typical Rosemont brick construction: a south-facing wall overlooking a side courtyard with a paved driveway, a small garden, and a narrow passage between two buildings. In this type of configuration, we must:
-
free up as much floor space as possible for circulation;
-
respect the necessary clearances for condenser ventilation;
-
limit the transmission of vibrations to the masonry;
-
protect the equipment from snow, ice and splashes.
The client's objective: to obtain a reliable system to air condition the entire floor in summer and provide highly efficient supplementary heating in winter, while remaining visually and audibly discreet for him… and for his neighbors.
Equipment selection: Sharp ZU1 wall-mounted heat pump
For this project, we installed a Sharp ZU1 wall-mounted heat pump of approximately 18,000 BTU, a typical capacity for a well-insulated, medium-sized home in Montreal.
This Sharp model is distinguished by:
-
Inverter technology that continuously modulates power according to actual demand;
-
a new generation A2L refrigerant (R-32) with a lower global warming potential than the older R-410A;
-
quiet operation, both indoors and outdoors;
-
excellent performance in low-temperature heating, ideal for Quebec winters.
Inside, the wall-mounted unit (not visible in the photo) has been positioned to ensure good air circulation in the main living areas, while respecting the existing layout of the dwelling.
Condenser installation: wall bracket and snow protection
The photo shows the Sharp outdoor unit mounted on a galvanized steel wall bracket anchored directly into the brick. This installation method offers several advantages in an area like Rosemont:
-
Clearance from the ground : the condenser is raised, which keeps it above the accumulation of snow and ice in winter. This also facilitates the drainage of condensation water in summer.
-
Mechanical protection : installed above the drainage stone strip, the condenser is protected from lawnmowers, snow shovels and dirt.
-
Freeing up ground space : the side courtyard remains clear for movement, taking out the rubbish or working in the garden.
-
Aesthetics : the parallel positioning to the brick wall and the chosen height allow for a clean and discreet visual line.
We use fixings sized to easily support the weight of the unit, taking into account wind and snow loads, as well as any potential vibrations. Anti-vibration pads are integrated under the unit's feet to limit noise transmission to the wall during compressor operation.
Drainage and clearance management around the unit
Beneath the condenser, a band of crushed stone can be seen along the foundation. This detail is more important than it appears:
-
It facilitates the drainage of condensation water in summer;
-
It prevents the formation of mud and splashes on the facade;
-
It limits the regrowth of vegetation directly under the unit, which could restrict air circulation.
We consistently follow Sharp's manufacturer's clearance recommendations around the unit:
-
lateral clearance from the wall;
-
free space at the rear for air intake;
-
clearance at the front for the discharge of hot or cold air.
This ensures optimal performance and extends the compressor's lifespan.
Refrigeration and electrical connections: safety and cleanliness
The photo shows the insulated refrigeration lines and the carefully secured power cable . The main points to highlight are:
-
The refrigerant lines are insulated with high-quality foam, protected by tape and a cover at the wall exit, in order to protect them from UV, shocks and weathering.
-
The passage through the masonry is protected by a metal piece and sealed to prevent water infiltration.
-
The electrical wiring is securely attached, with a dedicated circuit breaker inside and a disconnect device near the unit in accordance with current standards.
-
The visible A2L label indicates the use of a modern refrigerant, requiring careful installation by certified refrigeration technicians – something our team is perfectly capable of.
The whole setup provides a clean, legible and easily accessible installation for any future maintenance or service operations.
Four-season comfort in Rosemont–La Petite-Patrie
With this Sharp wall-mounted heat pump, the customer now benefits from:
-
efficient and quiet air conditioning to cope with the increasingly frequent heat waves in Montreal;
-
efficient heating even at very low temperatures, allowing for reduced use of the main heating system and substantial savings;
-
better control of indoor humidity , contributing to comfort and protection of the building;
-
of an optimized electricity bill , thanks to the Inverter compressor which works mainly at low speed rather than on/off.
The heat pump thus intelligently complements the existing system, while increasing the value of the property.
Why entrust your Sharp heat pump to AirGreen?
At AirGreen, we install and maintain Sharp wall-mounted heat pumps throughout Greater Montreal, including Rosemont–La Petite-Patrie, Ahuntsic, Villeray, Laval, the South Shore and the North Shore.
Our promise:
-
honest recommendations based on the reality of your building, your budget and your energy saving objectives;
-
an installation that complies with the latest electrical and refrigeration standards;
-
special attention to aesthetics (passage of lines, supports, height, noise level for you and your neighbors);
-
an accessible after-sales service, with maintenance, cleaning and diagnostics when needed.
Are you also considering installing a Sharp heat pump in a duplex, bungalow, or condo in Rosemont or elsewhere in Montreal? Our team will be happy to offer you a customized solution, whether it's for a simple replacement of an old air conditioner or for a complete energy conversion project.
The big day, step by step
The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.
We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
Model, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
Floors and furniture protected, wall plate position marked level, wall opening located.
A single opening, with the slope the drain needs to flow outside.
Set on a stand raised above the snow, with the clearances the manufacturer requires.
Connected, insulated and protected. The opening is then sealed against water, cold air and insects.
A dedicated circuit and an accessible disconnect near the outdoor unit.
Leak test, vacuum, then start-up and a check of heating and cooling.
Remote, modes, filters: we show you the essentials before we leave.
- The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
- The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
- Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
- The wall openingA single opening, with the slope the drain needs to flow outside.
- The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
- Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
- The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
- Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
- The walkthroughRemote, modes, filters: we show you the essentials before we leave.
What would it look like at your place?
Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.
Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.
Four mistakes we do not make
Flip each card to see what we do instead.
Your own project, step by step
What to do, season by season
Three habits per season for this unit. They take a few minutes and prevent many calls.
- Clean the indoor unit's filters.
- Clear leaves and debris left on the outdoor unit by winter.
- Test cooling before the first hot days.
- Clean the filters more often when the unit runs a lot.
- Keep plants away from the outdoor unit.
- Check that no water drips from the indoor unit.
- Rake the leaves around the outdoor unit.
- Test heating before the first cold days.
- Book periodic maintenance before winter.
- Keep snow away from the stand and the front of the unit.
- Let the unit defrost: it is normal.
- Never hit the ice on the fins; call us if the unit stays iced up.
Is your home ready?
Check what applies at your place. A "no" is not a refusal: it is what we sort out during the estimate.
Four statements: true or false?
It all comes down to details you have just seen.
1. In heating mode, the outdoor unit can produce water.
During defrost cycles. That water must drain away without forming ice.
2. You pick the capacity with a simple square-footage rule.
Windows, insulation, orientation and how the room is used all count. Capacity is chosen on site.
3. A multi-zone connects several indoor heads to a single condenser.
One head per room, all on the same condenser. Each room keeps its own temperature.
4. The disconnect can sit behind the patio furniture.
It must stay accessible: it is what shuts the unit off for service.
0 / 4 right answers
What people ask us about this kind of work
Does a wall-mounted heat pump heat in winter?
Wall-mounted or multi-zone: how do I choose?
Where does the outdoor unit go?
Are there grants?
Do I need a permit?
How cold can it heat?
How much can I save?
How is the LogisVert assistance calculated?
Is it noisy?
The outdoor unit is covered in ice: is that normal?
Does AirGreen hold the required licences?
Is the estimate free?
No question matches. Write to us: we answer.
More jobs to see, near you
By town, by equipment or by region: browse more than 4,700 published projects.
Each dot: a town where AirGreen has published projects. The glowing dot: this job.
Every house has its constraints. We see them before we install.
The on-site estimate is free and the quote follows within 24 hours.
Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).
