Installation of a Sharp wall-mounted heat pump on a flat roof in Rosemont–La Petite-Patrie
In Rosemont–La Petite-Patrie, AirGreen installed a Sharp Eco Inverter wall-mounted heat pump on the flat roof of a residential building. Elevated structure, roof protection, energy efficiency, and four-season comfort: discover how we optimized this system for Montreal's climate.

Take a tour of the installation
Each number is a point we check on site. Switch between summer and winter to watch air and heat move.
In summer, the outdoor unit rejects the house's heat outside.
Generic illustration of this type of installation, not a survey of this job site. Tap a number.
Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.
The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.
Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.
A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.
The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.
On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.
The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.
In the leafy Rosemont–La Petite-Patrie neighbourhood, we had the pleasure of installing a Sharp Eco Inverter wall-mounted heat pump for a residential apartment building. The goal: to provide a high-performance, discreet heating and cooling system perfectly suited to the realities of Montreal's flat roofs.
Project context: four-season comfort for an urban building
The building is typical of Rosemont: several apartments, brick facades, green alleyways, large mature trees, and a flat roof offering a beautiful view of downtown. The co-owners wanted:
-
Replacing aging and energy-inefficient equipment;
-
Improving summer comfort during heat waves;
-
Take advantage of the heat pump mode to reduce heating costs;
-
Minimize noise and visual impact on the facade.
The ideal solution: a Sharp wall-mounted heat pump , installed directly on the roof, to free up floor space and preserve the aesthetics of the building.
Equipment choice: Sharp Eco Inverter wall-mounted heat pump
We opted for a Sharp Eco Inverter wall-mounted heat pump , a reliable residential range designed for climates like ours.
This type of system offers several advantages:
-
Inverter technology : power modulation to maintain a stable temperature while reducing electricity consumption;
-
Quiet comfort : reduced noise level both inside and outside;
-
Heat pump function : a single unit provides gentle heating in mid-season and air conditioning in summer;
-
Energy efficiency : ideal for reducing electricity bills compared to traditional systems.
The Sharp outdoor condenser visible in the photo is paired with one or more discreet indoor wall heads, installed in the served dwellings.
Installation on a flat roof: stability, durability and respect for the roof
Installing a heat pump on a flat roof requires a rigorous approach. We have designed a specially adapted elevated support structure :
-
Galvanized steel frame fixed on distribution pads to protect the roof membrane;
-
Supports made of treated wood to absorb vibrations and distribute the load;
-
Elevated unit to promote water drainage, facilitate snow removal and protect the unit from the accumulation of ice or debris;
-
Clearances respected all around the condenser to guarantee excellent air circulation and therefore the performance of the Sharp.
This approach ensures both the safety of the equipment and respect for the integrity of the roof , a crucial point for condominiums and owners of rental buildings.
Management of refrigeration connections and power supply
Invisible details often make all the difference in the lifespan of an installation. On this project, we paid particular attention to:
-
Protection of refrigeration pipes in UV-resistant cable trays and covers;
-
The insulation is carefully sealed to prevent water infiltration and premature degradation;
-
The watertight passage through the roof for electrical connections and cables;
-
The dedicated electrical connection , compliant with current standards, with a safety circuit breaker easily accessible for maintenance.
The result: a clean, organized installation, designed to last and to facilitate future maintenance interventions.
Performance and comfort for the residents of Rosemont–La Petite-Patrie
With this Sharp wall-mounted heat pump , the occupants now benefit from:
-
With a cool, summery comfort , even on the hottest days in Montreal;
-
Efficient and uniform heating in spring and autumn, as a complement to or replacement for existing systems;
-
It operates silently , both inside the apartments and on the roof, which is valuable in a dense neighborhood like Rosemont;
-
Reduced energy bills thanks to the high efficiency of Inverter technology.
The machine is sized to offer a balance between power, comfort and economy, while remaining discreet in the urban landscape.
Safety, maintenance and longevity of the Sharp heat pump
At AirGreen, we know that a good installation doesn't end on commissioning day. For this project:
-
We carefully checked the refrigerant pressures and Sharp operating parameters;
-
We provided the client with all the information on preventive maintenance (cleaning of filters, clearances around the unit, periodic inspections);
-
We offer regular maintenance visits to ensure optimal system performance year after year.
A properly installed and well-maintained heat pump is an investment that pays for itself quickly, especially in a climate like Montreal's.
Why entrust your project to AirGreen?
By choosing AirGreen for this Sharp wall-mounted heat pump installation in Rosemont–La Petite-Patrie , the client benefited from:
-
From a team specializing in residential systems in Greater Montreal;
-
Comprehensive support , from equipment selection to commissioning;
-
An installation carried out according to best practices, in compliance with electrical and mechanical standards;
-
An accessible, human and transparent after-sales service.
Whether you are an owner-occupier, investor or condominium association, we always adapt our approach to the reality of your building and your comfort and savings objectives.
Conclusion: a Sharp heat pump perfectly integrated into the urban landscape of Rosemont
This installation of a Sharp Eco Inverter wall-mounted heat pump on a flat roof , in the heart of Rosemont–La Petite-Patrie, perfectly illustrates what we love to do at AirGreen:
-
To offer effective and elegant solutions ;
-
Respect the architecture and constraints of the building;
-
To provide occupants with four-season comfort while reducing the energy footprint.
Are you considering installing a Sharp wall-mounted heat pump or another HVAC system in Greater Montreal?
Contact us : we would be happy to assess your situation and offer you the best solution for your building.
The big day, step by step
The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.
We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
Model, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
Floors and furniture protected, wall plate position marked level, wall opening located.
A single opening, with the slope the drain needs to flow outside.
Set on a stand raised above the snow, with the clearances the manufacturer requires.
Connected, insulated and protected. The opening is then sealed against water, cold air and insects.
A dedicated circuit and an accessible disconnect near the outdoor unit.
Leak test, vacuum, then start-up and a check of heating and cooling.
Remote, modes, filters: we show you the essentials before we leave.
- The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
- The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
- Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
- The wall openingA single opening, with the slope the drain needs to flow outside.
- The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
- Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
- The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
- Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
- The walkthroughRemote, modes, filters: we show you the essentials before we leave.
What would it look like at your place?
Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.
Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.
Four mistakes we do not make
Flip each card to see what we do instead.
Your own project, step by step
What to do, season by season
Three habits per season for this unit. They take a few minutes and prevent many calls.
- Clean the indoor unit's filters.
- Clear leaves and debris left on the outdoor unit by winter.
- Test cooling before the first hot days.
- Clean the filters more often when the unit runs a lot.
- Keep plants away from the outdoor unit.
- Check that no water drips from the indoor unit.
- Rake the leaves around the outdoor unit.
- Test heating before the first cold days.
- Book periodic maintenance before winter.
- Keep snow away from the stand and the front of the unit.
- Let the unit defrost: it is normal.
- Never hit the ice on the fins; call us if the unit stays iced up.
Is your home ready?
Check what applies at your place. A "no" is not a refusal: it is what we sort out during the estimate.
Four statements: true or false?
It all comes down to details you have just seen.
1. In heating mode, the outdoor unit can produce water.
During defrost cycles. That water must drain away without forming ice.
2. You pick the capacity with a simple square-footage rule.
Windows, insulation, orientation and how the room is used all count. Capacity is chosen on site.
3. A multi-zone connects several indoor heads to a single condenser.
One head per room, all on the same condenser. Each room keeps its own temperature.
4. The disconnect can sit behind the patio furniture.
It must stay accessible: it is what shuts the unit off for service.
0 / 4 right answers
What people ask us about this kind of work
Does a wall-mounted heat pump heat in winter?
Wall-mounted or multi-zone: how do I choose?
Where does the outdoor unit go?
Are there grants?
Do I need a permit?
How cold can it heat?
How much can I save?
How is the LogisVert assistance calculated?
Is it noisy?
The outdoor unit is covered in ice: is that normal?
Does AirGreen hold the required licences?
Is the estimate free?
No question matches. Write to us: we answer.
More jobs to see, near you
By town, by equipment or by region: browse more than 4,700 published projects.
Each dot: a town where AirGreen has published projects. The glowing dot: this job.
Every house has its constraints. We see them before we install.
The on-site estimate is free and the quote follows within 24 hours.
Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).
