Installation of a Zephyr wall-mounted heat pump in Sainte-Dorothée (Laval)
AirGreen installed a Zephyr wall-mounted heat pump in Sainte-Dorothée, Laval , in a bright room near a window. Discreet integration, efficient air distribution, and reliable comfort for both summer and winter.
In summer, the outdoor unit rejects the house's heat outside.
Generic illustration of this type of installation, not a survey of this job site. Tap a number.
Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.
The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.
Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.
A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.
The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.
On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.
The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.
In Sainte-Dorothée , in a bright and very open-concept residential setting, we installed a Zephyr wall-mounted heat pump to provide consistent comfort year-round without cluttering the space. This type of project is common in Laval: people are looking for an efficient, discreet solution that can adapt to the typical temperature variations of Quebec, from the bitter cold of winter to the hot and humid days of July.
Machine type: wall-mounted heat pump (mini-split)
The photo shows a Zephyr wall-mounted indoor unit installed high up, with air distribution via a motorized louver and a digital display (notably showing a setpoint of around 19°C ). This is exactly the "mini-split" format favored for:
-
to quickly air-condition a living room,
-
to heat efficiently during the shoulder seasons (and in winter, depending on the configuration),
-
avoid major, often costly and invasive pipework.
Brand: Zephyr (confirmed)
According to the information provided, the system brand is Zephyr . We naturally integrate it into our approach: selecting the right location, optimizing comfort, and a clean and durable finish.
Model: Zephyr – residential wall-mounted range (exact model not legible)
The exact model is not clearly visible in the photo. We therefore describe the equipment accurately and consistently: a recent Zephyr wall-mounted residential-grade heat pump with a sleek design, designed to meet the typical needs of a house or apartment in Laval.
Prominent installation details visible in the photo
This installation is a good example of what we aim for at AirGreen: performance + aesthetics + real everyday comfort.
-
High positioning, under the ceiling : ideal for wide and even diffusion in the room.
-
Proximity to a window : very practical for stabilizing the area where variations are often most felt (direct sunlight, glazing, drafts).
-
Clear wall in front of the unit : no immediate obstruction, allowing the airflow to “carry” further and avoid the localized blast effect.
-
Integration into a multifunctional space : we see a living/activity environment (accessories at the bottom of the image), where thermal comfort must remain constant, without excessive noise.
Why does this type of installation work so well in Laval?
In areas like Sainte-Dorothée, apartments and houses often offer bright rooms, sometimes with sloped ceilings or open layouts. A Zephyr wall-mounted heat pump is therefore an excellent choice because it allows you to:
-
a rapid response to temperature variations (morning/evening, sun, cooking, physical activity),
-
Simple daily management via remote control and automatic modes,
-
a minimal visual footprint : the unit blends into the decor, without dominating the room.
Our AirGreen method: sustainable comfort and a clean finish
A wall installation isn't just about "laying your head down." To ensure a flawless and long-lasting result, we pay particular attention to:
-
the location (diffusion, comfort, noise, traffic),
-
the quality of the connections and the sealing,
-
condensation management (reliable drainage, adequate slope),
-
a finish that remains clean over time (alignment, stability, integration).
This is what makes the difference between a system that "works" and a system that becomes a true daily comfort.
Simple tips to keep your Zephyr performing well
To preserve efficiency and air quality:
-
clean the filters regularly (a simple, very cost-effective action).
-
Keep the front of the unit clear for good airflow.
-
Plan for complete periodic maintenance (internal cleaning, drainage, performance).
How it goes, from the first call to the end
The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.
We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
Model, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
Floors and furniture protected, wall plate position marked level, wall opening located.
A single opening, with the slope the drain needs to flow outside.
Set on a stand raised above the snow, with the clearances the manufacturer requires.
Connected, insulated and protected. The opening is then sealed against water, cold air and insects.
A dedicated circuit and an accessible disconnect near the outdoor unit.
Leak test, vacuum, then start-up and a check of heating and cooling.
Remote, modes, filters: we show you the essentials before we leave.
- The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
- The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
- Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
- The wall openingA single opening, with the slope the drain needs to flow outside.
- The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
- Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
- The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
- Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
- The walkthroughRemote, modes, filters: we show you the essentials before we leave.
And at your place?
Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.
Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.
What to do, season by season
Three habits per season for this unit. They take a few minutes and prevent many calls.
- Clean the indoor unit's filters.
- Clear leaves and debris left on the outdoor unit by winter.
- Test cooling before the first hot days.
- Clean the filters more often when the unit runs a lot.
- Keep plants away from the outdoor unit.
- Check that no water drips from the indoor unit.
- Rake the leaves around the outdoor unit.
- Test heating before the first cold days.
- Book periodic maintenance before winter.
- Keep snow away from the stand and the front of the unit.
- Let the unit defrost: it is normal.
- Never hit the ice on the fins; call us if the unit stays iced up.
Which type of equipment for your project?
Pick what looks like your need.
Four mistakes we do not make
Flip each card to see what we do instead.
What people ask us about this kind of work
Does a wall-mounted heat pump heat in winter?
Wall-mounted or multi-zone: how do I choose?
Where does the outdoor unit go?
Are there grants?
Do I need a permit?
How cold can it heat?
How much can I save?
How is the LogisVert assistance calculated?
Is it noisy?
The outdoor unit is covered in ice: is that normal?
Does AirGreen hold the required licences?
Is the estimate free?
No question matches. Write to us: we answer.
Useful pages for what comes next
More jobs to see, near you
By town, by equipment or by region: browse more than 4,700 published projects.
Each dot: a town where AirGreen has published projects. The glowing dot: this job.
Tell us about your house. We come and see it for free.
The on-site estimate is free and the quote follows within 24 hours.
Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).