Project

Installation of a GREE FREE MATCH R32 TripleZone heat pump in La Prairie – 3-zone system, 3 wall units for a residence on the South Shore

AirGreen installs a GREE FREE MATCH R32 TripleZone heat pump in La Prairie: 3 zones, 3 wall units, precise comfort, clean integration, and HVAC expertise on the South Shore.

By AirGreen Climatisation & Chauffage Admin15 min read
Installation of a GREE FREE MATCH R32 TripleZone heat pump in La Prairie – 3-zone system, 3 wall units for a residence on the South Shore
Installation of a GREE FREE MATCH R32 TripleZone heat pump in La Prairie – 3-zone system, 3 wall units for a residence on the South Shore
–chapters in this story
15 minreading time
–type of installation
2026year published
The tour

Take a tour of the installation

Each number is a point we check on site. Switch between summer and winter to watch air and heat move.

Generic diagram: wall-mounted heat pump, indoor and outdoor units

In summer, the outdoor unit rejects the house's heat outside.

Generic illustration of this type of installation, not a survey of this job site. Tap a number.

  1. Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.

  2. The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.

  3. Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.

  4. A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.

  5. The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.

  6. On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.

  7. The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.

The job

A GREE multi-zone installation in La Prairie where every interior detail mattered

In this residence in La Prairie, on the South Shore of Montreal, our AirGreen team installed a TripleZone GREE FREE MATCH R32 heat pump, composed of 3 zones and 3 wall heads. The project aimed to offer more precise comfort in several areas of the house without requiring multiple outdoor units or compromising the already well-designed interior aesthetics.

The installation photo shows one of the GREE wall heads mounted very high on a wall, near the ceiling and close to an architectural corner. The unit is well aligned, discreet, and its display shows a temperature of 23 °C, indicating that the system is running and ready to provide comfortable temperature control. The open louvers, oriented to promote effective air diffusion in the room, are also noticeable. In an indoor environment where walls are clear, carefully decorated, and visible daily, installation precision becomes essential.

This type of HVAC installation requires a more elaborate approach than a simple equipment replacement. A multi-zone heat pump must be designed as a complete system: placement of the heads, routing of refrigerant lines, condensate drainage, electrical coordination, choice of the outdoor unit, accessibility for HVAC maintenance, and balance between performance and appearance. In La Prairie, our mandate was to deliver a reliable, clean solution adapted to the daily life of the occupants.

Why a TripleZone heat pump for this residence in La Prairie

Houses in La Prairie often have layouts where a single wall unit is not enough to ensure uniform comfort. Between the main open area, bedrooms, basement, office, or sun-exposed zones, temperature differences can become noticeable. A TripleZone – 3 heads system allows treating each space according to its actual use.

With the GREE FREE MATCH R32, occupants can control three zones of the house separately. This avoids the typical compromises of a single-zone system, where one room becomes too cool while another remains too warm. In cooling mode, this setup helps better manage heat and humidity periods on the South Shore. In heating mode, it offers a very practical solution in mid-season and can contribute to comfort during colder periods, depending on conditions, building configuration, and occupant needs.

For this project, the flexibility of the multi-zone system was a major advantage. The owners wanted a solution capable of adapting to different rooms without multiplying visible equipment outside. A single well-positioned outdoor unit, connected to three indoor heads, reduces clutter while improving room-by-room control.

The GREE FREE MATCH R32 model: a well-suited solution for 3-zone projects

The GREE FREE MATCH R32 system is designed for multi-zone installations where several indoor units are connected to the same outdoor unit. This type of equipment is particularly relevant in residences where comfort, efficient use, and discreet integration are desired.

The refrigerant R32 used in this range is part of modern residential air conditioning and heating technologies. It allows manufacturers to design efficient, compact devices suited to the current needs of homeowners. For customers, the main interest remains concrete: a system capable of modulating according to the demands of different zones, without having to run the entire house at the same level all the time.

In an installation like this, the sought-after benefits are clear:

  • better temperature control in three distinct spaces;
  • a reduction of uncomfortable zones in the house;
  • a single outdoor unit to power three heads;
  • a more discreet appearance than an accumulation of single-zone systems;
  • more flexible use according to schedules and occupied rooms;
  • improved comfort during the hot and humid summer days;
  • a practical heating solution for several periods of the year.

It is important to specify that, for multi-zone systems, the exact performance and eligibility for subsidies may depend on the precise combination of the outdoor unit and the installed indoor units. At AirGreen, we verify the relevant technical information before installation to guide customers with realistic data tailored to the actual model installed.

A wall head installed high, near a corner: a technical and aesthetic choice

The image of this installation in La Prairie reveals an important detail: the GREE wall head is installed very close to the ceiling, in the upper part of the wall, next to a corner. This configuration requires very precise execution. The unit must be perfectly level, well cleared to allow air return, accessible for filter maintenance, and placed to distribute air without causing discomfort.

In this room, the presence of decorative elements on the wall and the opening on the right limited placement options. The goal was not simply to find an available spot but to choose an effective location for air distribution while respecting the room's appearance. The result is understated: the unit fits into the upper part of the wall, without encroaching on living space or harming decorative elements.

Poor positioning could have caused several problems: air blown directly on occupants, difficulty opening the front panel, poor circulation, more noticeable noise, or less convenient maintenance. We therefore paid special attention to clearances, height, alignment, and the orientation of the louvers.

The challenges of a 3-zone installation in an already furnished house

Installing a TripleZone heat pump in an occupied residence requires rigorous coordination. Unlike new construction where some passages can be planned before wall finishing, an already furnished house imposes real constraints: finished walls, furniture, decorations, openings, limited access, and high expectations regarding the cleanliness of the result.

In this project in La Prairie, the main challenges involved integrating the indoor heads without creating visual heaviness. Each unit had to be strategically placed, not only to cool or heat its zone but also to avoid unnecessary duct runs and limit the impact on the exterior of the house.

Our team analyzed:

  • the natural direction of air circulation;
  • distances between the heads and the outdoor unit;
  • gravity drainage possibilities;
  • areas where a clean wall penetration could be made;
  • locations allowing for easy maintenance;
  • the visual impact of external ducts;
  • electrical constraints;
  • the real needs of the occupants in each room.

This preparatory work is essential. In a multi-zone system, a mistake in a single zone can affect the overall customer experience. A poorly placed unit, a badly planned drain, or an overly visible refrigerant line can turn a good machine into a disappointing installation. At AirGreen, we treat each zone as a small project in itself, integrated into a coherent whole.

A clean HVAC installation, designed to last and simplify daily comfort

The quality of an HVAC installation is often judged by details that are not immediately noticeable. A well-aligned wall unit, clean penetrations, well-organized ducts, reliable drainage, well-made connections, and a complete commissioning make all the difference over time.

For this GREE FREE MATCH R32 heat pump installed in La Prairie, we followed a structured work method focused on reliability. The refrigerant lines were carefully connected, the sealing was checked, the system was vacuumed according to best practices, and each zone was tested individually. This step confirms that the units communicate properly with the outdoor unit, that operating modes respond correctly, that drains evacuate adequately, and that remote controls are linked to the correct zones.

Multi-zone comfort: a tangible everyday advantage

Once the system is running, the main benefit for occupants is the freedom to control each zone according to its use. In a family home, not all rooms are occupied at the same time. A bedroom may require a cooler temperature in the evening, while a living area can be kept comfortable during the day. A home office may need precise adjustment during working hours without unnecessarily cooling or heating other rooms.

This flexibility is one of the great advantages of a 3-zone heat pump. It allows smarter comfort management, especially in houses where temperature differences are caused by sun exposure, high ceilings, closed rooms, or differences between floors.

In La Prairie, where many homes combine open spaces, multiple floors, and versatile rooms, a multi-zone solution can significantly improve quality of life. Comfort becomes more stable, more localized, and easier to adjust.

La Prairie, South Shore: very specific HVAC needs

The South Shore includes a wide variety of building types: single-family homes, townhouses, condos, semi-detached houses, and renovated properties. In La Prairie, cooling and heating needs are often influenced by sun exposure, size, extensions, insulation quality, and the use of different rooms.

We regularly carry out similar installations in Longueuil, Brossard, Candiac, Saint-Constant, Sainte-Catherine, and other areas of the South Shore. We also find the same concerns among our clients in Montreal, Laval, and the North Shore: choosing the right system, avoiding overly visible installations, reducing temperature differences, and obtaining professional service from the first appointment to the final start-up.

Local experience matters a lot. Installing a heat pump in Greater Montreal is not just about following a technical sheet. You need to know the types of walls, access constraints, electrical requirements, owners' aesthetic preferences, and Quebec's climatic realities.

Mistakes to avoid before choosing a multi-zone heat pump

A TripleZone system can offer excellent results, but only if it is well designed. Several mistakes often occur when owners compare options without technical support.

Choosing locations solely based on ease of installation

The easiest wall to drill is not always the best location. A head must be positioned to effectively distribute air in the targeted area. In the La Prairie project, the location visible in the photo was carefully chosen to balance diffusion, clearance, and visual integration.

Underestimating the importance of drainage

Each head produces condensation water in cooling mode. This water must be reliably drained. An insufficient slope, a poorly planned path, or a badly placed pump can cause long-term problems. Drainage must always be planned from the design stage of the installation.

Choosing capacity without analyzing the zones

A house is not measured only in square feet. Each area has its own needs. A closed bedroom, an open area, and a space with large windows do not respond in the same way. A good analysis helps better balance the system and avoid discomfort.

Neglecting future maintenance

A head installed too close to an obstacle can become difficult to maintain. Filters must remain accessible. The front panel must be able to open properly. Technicians must be able to perform HVAC maintenance without having to move an excessive number of objects or dismantle decorative elements.

Commissioning: the step that confirms the quality of the work

An installation is not complete when the units are fixed to the wall. Commissioning is a crucial step. For this GREE FREE MATCH R32 system, we tested the three zones to confirm the proper functioning of each head. The display visible in the photo, set to 23 °C, shows this phase where the device is activated, checked, and adjusted.

Our technicians specifically validate:

  • response of each indoor unit;
  • communication with the outdoor unit;
  • operation of the louvers;
  • blow temperature;
  • condensate drainage;
  • unusual noises;
  • system stability;
  • basic settings for the user;
  • filter maintenance instructions.

This step also allows us to explain to the client how to use their system efficiently. Good equipment delivers better results when well understood: temperature settings, heating mode, cooling mode, ventilation, dehumidification, filter cleaning, and good seasonal usage practices.

Grants and documentation: a check to be done according to the installed combination

Homeowners installing a heat pump often want to know if their system qualifies for financial assistance. For multi-zone systems like the GREE FREE MATCH R32, it is necessary to verify the exact combination of units, the current program criteria, and the required documents.

At AirGreen, we help clients gather important information: installed model, invoice, technical details, and available documentation. This thoroughness is especially important for multi-head systems, as eligibility can vary depending on the actual configuration. Rather than giving a generic answer, we prefer to validate the data specific to each project.

Why choose AirGreen for a TripleZone installation in La Prairie

Choosing AirGreen for a heat pump installation in La Prairie means entrusting your project to a team that understands multi-zone systems and the realities of buildings in Greater Montreal. We don’t just install devices. We assess the home, suggest suitable locations, explain the advantages and limitations of each option, and then carry out a clean and durable installation.

Our expertise covers residential and light commercial projects in Montreal, Laval, Longueuil, on the North Shore and the South Shore. In each area, we adapt our method to the building’s constraints. A house in La Prairie does not always face the same challenges as a condo in Montreal or a property in Laval, but the goal remains the same: to deliver a reliable, aesthetic, and efficient system.

This project clearly illustrates our approach. The wall unit visible in the photo is installed with restraint, high on the wall, in a spot where the available space had to be used precisely. With the vents open, the active display, and clean integration, it shows a system ready to operate without visual overload.

A result that combines comfort, control, and finish

This installation of a GREE FREE MATCH R32 TripleZone heat pump in La Prairie meets a very concrete need: to offer independent comfort in three zones of the residence, while maintaining a discreet and well-integrated installation. The system allows occupants to better manage the temperature according to rooms, seasons, and lifestyle habits.

The success of the project relies on three elements: the right choice of equipment, careful planning, and rigorous execution. With a multi-zone heat pump, these three aspects are inseparable. The machine must be suited to the building, the locations must be thoughtfully chosen, and the installation must follow professional standards.

For owners in La Prairie, Longueuil, Montreal, Laval, the North Shore, and the South Shore, this type of system offers a very interesting solution when several rooms require better-controlled comfort. Properly installed, a GREE FREE MATCH R32 TripleZone becomes a daily comfort tool: easy to use, discreet in the home, and capable of meeting varied needs.

The steps

The big day, step by step

The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.

Step 1 of 9The on-site estimate

We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.

  1. The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
  2. The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
  3. Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
  4. The wall openingA single opening, with the slope the drain needs to flow outside.
  5. The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
  6. Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
  7. The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
  8. Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
  9. The walkthroughRemote, modes, filters: we show you the essentials before we leave.
Your numbers

What would it look like at your place?

Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.

Size checkYour baseboards, in BTU/h
–BTU/h of installed electric heat

    Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.

    Mistakes avoided

    Four mistakes we do not make

    Flip each card to see what we do instead.

    Going further

    Your own project, step by step

    Through the seasons

    What to do, season by season

    Three habits per season for this unit. They take a few minutes and prevent many calls.

    • Clean the indoor unit's filters.
    • Clear leaves and debris left on the outdoor unit by winter.
    • Test cooling before the first hot days.
    At your place

    Is your home ready?

    Check what applies at your place. A "no" is not a refusal: it is what we sort out during the estimate.

    0 / 6 checked
    True or false

    Four statements: true or false?

    It all comes down to details you have just seen.

    1. In heating mode, the outdoor unit can produce water.

    2. You pick the capacity with a simple square-footage rule.

    3. A multi-zone connects several indoor heads to a single condenser.

    4. The disconnect can sit behind the patio furniture.

    Frequently asked questions

    What people ask us about this kind of work

    12 questions
    Does a wall-mounted heat pump heat in winter?
    Yes, it heats and cools. Its capacity drops in very cold weather; the operating range depends on the model and is listed on its spec sheet.
    Wall-mounted or multi-zone: how do I choose?
    One wall head and one condenser outside: the direct solution for a room or an open area. For two to five rooms, a multi-zone puts one head in each room on a single condenser.
    Where does the outdoor unit go?
    Where it stays above the snow, clear and accessible, away from walkways. We decide it with you during the estimate.
    Are there grants?
    Depending on the model and your situation, assistance programs may apply, including Hydro-Québec's LogisVert. AirGreen checks the model number before quoting an amount. See the grants.
    Do I need a permit?
    Rules vary from city to city: location, distances, noise. See permits and by-laws, and we check for your address.
    How cold can it heat?
    It depends on the model. According to Hydro-Québec, newer models work down to a temperature between −15 °C and −25 °C, and some cold-climate models are certified lower. The minimum temperature is on each unit's spec sheet.
    How much can I save?
    Hydro-Québec says a heat pump can be up to three times more efficient than baseboards for heating in the colder months. The result depends on the house, the climate and how it is used.
    How is the LogisVert assistance calculated?
    For ENERGY STAR cold-climate certified heat pumps, Hydro-Québec lists assistance of $120 per 1,000 BTU/h of heating capacity at −8 °C. AirGreen checks the exact model before quoting an amount; only Hydro-Québec confirms the assistance granted. See the grants.
    Is it noisy?
    The sound level depends on the model and is listed in decibels on each unit's spec sheet. Location matters too: when possible, we avoid putting the outdoor unit under a bedroom window.
    The outdoor unit is covered in ice: is that normal?
    Some frost is: the unit runs defrost cycles. Never hit the ice. If the unit stays iced up or stops heating, call us.
    Does AirGreen hold the required licences?
    Yes. AirGreen holds RBQ licence 5645-9605-01, subclasses 15.8 Ventilation, 15.10 Refrigeration and 16 Electricity.
    Is the estimate free?
    Yes. The on-site estimate is free and the quote follows within 24 hours. Book my free estimate.

    Could this job help a neighbour?

    Share
    Similar projects

    More jobs to see, near you

    By town, by equipment or by region: browse more than 4,700 published projects.

    Each dot: a town where AirGreen has published projects. The glowing dot: this job.

    All our projects

    Your project

    Every house has its constraints. We see them before we install.

    The on-site estimate is free and the quote follows within 24 hours.

    • RBQ licence5645-9605-01 · 15.8, 15.10, 16
    • EstimateOn site, free
    • QuoteWithin 24 hours

    Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).

    Leave a comment