Installation of a Haxxair T2D Wall-Mounted Mini Split in Laval
Discover how AirGreen transformed a home in Laval with the Mini Split Haxxair T2D. Click to learn more!
In summer, the outdoor unit rejects the house's heat outside.
Generic illustration of this type of installation, not a survey of this job site. Tap a number.
Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.
The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.
Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.
A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.
The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.
On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.
The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.
Replacement of a Haxxair T2D Wall-Mounted Mini Split in Laval
When it comes to quality HVAC services in Montreal and its surrounding regions, there's no better choice than AirGreen. Our portfolio includes a rich selection of successful projects, and the recent installation in Laval of a state-of-the-art Haxxair T2D Wall-Mounted Mini Split is a testament to our commitment and expertise.
Client's Challenge
The project was simple yet important - a replacement of an aging heat pump with a new and efficient one. We were faced with a delicate task: reusing the existing pipes to avoid additional holes and ensuring their optimal condition for the new installation.
The Haxxair T2D Wall-Mounted Mini Split
At the heart of this project lies the Haxxair T2D Wall-Mounted Mini Split, a device that embodies technological advancement and consumer satisfaction. With a robust capacity of 18,000 BTU, it promises to deliver maximum comfort and optimal temperature regulation in any home.
What sets the Haxxair T2D apart is its design, incorporating a wall-mounted setup that saves space and optimizes air distribution. This compact yet powerful machine promises to be a long-lasting, reliable, and efficient solution to any homeowner's HVAC needs.
The AirGreen Process
At AirGreen, we pride ourselves on our methodical approach to any task. This particular installation began with a thorough inspection of the existing piping system. Our team carefully examined the old pipes for any potential leaks or faults, ensuring a clean slate for the new heat pump.
Upon successful inspection, we set about the task of cleansing the pipes. A meticulous washing process followed, removing any residual particles or contaminants. This was a crucial step in ensuring the smooth operation and longevity of the newly installed Haxxair T2D.
Installation Success
Finally, the moment had arrived to install the new Haxxair T2D Wall-Mounted Mini Split. The replacement was straightforward and painless, thanks to the diligence and skill of our experienced technicians.
In the end, we left a satisfied customer enjoying the quiet, efficient, and high-quality operation of their new heat pump. The installation was seamless, with no extra holes or unsightly modifications to the beautiful Laval home.
AirGreen - Your Trusted HVAC Partner
The successful installation of the Haxxair T2D in Laval is just another example of our unwavering dedication to quality and customer satisfaction. At AirGreen, we go beyond simply providing HVAC services - we deliver comfort, reliability, and peace of mind, one installation at a time.
Our reputation in Montreal, Laval, Longueuil, the North Shore, and the South Shore is built on a strong foundation of trust and expertise. When you choose AirGreen, you're not just selecting an HVAC company - you're choosing a committed partner in creating the perfect home environment.
How it goes, from the first call to the end
The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.
We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
Model, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
Floors and furniture protected, wall plate position marked level, wall opening located.
A single opening, with the slope the drain needs to flow outside.
Set on a stand raised above the snow, with the clearances the manufacturer requires.
Connected, insulated and protected. The opening is then sealed against water, cold air and insects.
A dedicated circuit and an accessible disconnect near the outdoor unit.
Leak test, vacuum, then start-up and a check of heating and cooling.
Remote, modes, filters: we show you the essentials before we leave.
- The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
- The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
- Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
- The wall openingA single opening, with the slope the drain needs to flow outside.
- The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
- Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
- The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
- Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
- The walkthroughRemote, modes, filters: we show you the essentials before we leave.
And at your place?
Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.
Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.
What to do, season by season
Three habits per season for this unit. They take a few minutes and prevent many calls.
- Clean the indoor unit's filters.
- Clear leaves and debris left on the outdoor unit by winter.
- Test cooling before the first hot days.
- Clean the filters more often when the unit runs a lot.
- Keep plants away from the outdoor unit.
- Check that no water drips from the indoor unit.
- Rake the leaves around the outdoor unit.
- Test heating before the first cold days.
- Book periodic maintenance before winter.
- Keep snow away from the stand and the front of the unit.
- Let the unit defrost: it is normal.
- Never hit the ice on the fins; call us if the unit stays iced up.
Which type of equipment for your project?
Pick what looks like your need.
Four mistakes we do not make
Flip each card to see what we do instead.
What people ask us about this kind of work
Does a wall-mounted heat pump heat in winter?
Wall-mounted or multi-zone: how do I choose?
Where does the outdoor unit go?
Are there grants?
Do I need a permit?
How cold can it heat?
How much can I save?
How is the LogisVert assistance calculated?
Is it noisy?
The outdoor unit is covered in ice: is that normal?
Does AirGreen hold the required licences?
Is the estimate free?
No question matches. Write to us: we answer.
Useful pages for what comes next
More jobs to see, near you
By town, by equipment or by region: browse more than 4,700 published projects.
Each dot: a town where AirGreen has published projects. The glowing dot: this job.
Tell us about your house. We come and see it for free.
The on-site estimate is free and the quote follows within 24 hours.
Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).