Fantech HRV SHR 700 Air Exchanger | Montreal, Laval, Longueuil, South Shore and North Shore

In stock
SKU: SHR 700
HRV
01 · Good to know

What you should know about this one

Published, verifiable facts, not brochure claims.

700 cfmSHR 700 code: 700 cfm at 0.4 in, side ducting

According to the Fantech manual, the 700 in the code means 700 cfm at 0.4 in and the S means side ducting. The brochure gives 720 cfm at 0.4 in, drawing 5.6 A at 120 V, and weighs 215 lb.

BPMRecirculation defrost available with the BPM module

Standard defrost shuts down the supply fan. With the optional BPM bypass module, offered on SHR models only, a motorized damper closes the fresh-air intake so indoor air circulates through the core without creating negative pressure.

ExhaustIt defrosts by pausing the fresh air for a few minutes

In cold weather, the supply fan stops for a few minutes while the exhaust keeps running, so warm indoor air thaws the core. During the cycle the house is briefly under negative pressure; if you have a fireplace or a naturally vented combustion appliance, mention it to our estimator.

HRVIt recovers heat, not moisture

Excess moisture leaves the house. In Québec, that's the right choice in most cases: in winter, a home almost always has too much humidity, not too little.

LifetimeThe core warranty

The core does the work and is the most expensive part to replace. Motors and parts: 3 years.

02 · Installation

What it needs on site

Side connectionSide ports
Condensate drainRequired
215 lbUnit weight
120 VPower supply

In a condo with no floor drain, or with little ceiling clearance, we usually look at a side-port model instead. Our estimator checks the location, the drain and the duct route before ordering.

Complete spec sheetData and cited sources
Type
HRV
Connection
Side ports
Condensate drain
Required
Defrost cycle
Exhaust only (supply fan off)
Filters
Washable MERV 3 filters (exhaust and supply); MERV 8 or MERV 13 upgrade
Weight
215 lb
Power supply
120 V
Warranty — core
Lifetime
Warranty — motors
3 years
Warranty — parts
3 years
Spec sheet (French)
PDF
Spec sheet (English)
PDF

The manufacturer doesn't publish an efficiency at −25 °C for this model; we don't make one up.

Talk to an HVAC technician before you choose

We calculate the airflow room by room, check the location and the drain, and give you an installed price. Balancing is measured at commissioning, not estimated.

Fantech SHR 700: 720 cfm at 0.4 in. with side connections

For a classroom, a clinic, a salon or a shop that exceeds the capacity of a 450, the Fantech SHR 700 is the next step up in the SHR series. Fantech's brochure gives 720 cfm at 0.4 in. for this light commercial HRV, on a simple 120 V circuit.

Like most commercial units, the Fantech SHR 700 is not listed in the HVI directory: it therefore has neither a certified net airflow nor a published SRE the way a residential HRV does. We select it and set it up based on your building's ventilation calculation.

SHR 700 code: 700 cfm at 0.4 in.

According to Fantech's manual, S stands for side connections (Side Ducting), H for heat recovery and R for the remote control option; the number gives the airflow class at 0.4 in. The manual uses the SHR 700 itself as its example: 700 cfm at 0.4 in. The brochure gives 720 cfm at 0.4 in., with 5.6 A on 120 V, for a weight of 215 lb.

Standard or recirculation defrost

By default, the SHR defrosts by stopping the fresh air fan. The BPM bypass module, offered as an option and available only on SHR units, changes the approach: from −5 °C, a motorized damper blocks the fresh air, the exhaust fan stops and the supply fan switches to high speed to circulate room air through the core. Fantech specifies that there is then no negative pressure in the building.

Efficiency and power consumption

The brochure lists a sensible effectiveness of 55% in heating, based on the core's AHRI 1060 data, for a power draw of 670 W. That works out to about 1.1 cfm per watt at 0.4 in. We set the speed to the calculated airflow, which reduces actual consumption.

Installation: weight, connections and drain

The Fantech documents we have do not give the SHR 700 cabinet dimensions: we confirm them with the manufacturer before planning the location and the ducts. At 215 lb, the unit needs a solid suspension structure or platform. For service, the motors and the core slide out on removable sliding rails, and the reversible door panels open on the accessible side. A drain is required. Condensate, including during defrost, must flow to a drain or a condensate pump, with a P-trap in the hose to keep odours from coming back up. The unit and its condensate hoses must be located in a heated space, above freezing.

ECO-Touch IAQ control

For this series, Fantech offers the ECO-Touch IAQ control. Its ECO mode selects the mode and speed according to the season, and its total volatile organic compounds sensor raises fresh air and exhaust airflow when the air becomes loaded with cleaning solvents or cooking odours. For the Fantech SHR 700, it is a simple way to ventilate more during busy hours only.

Filter maintenance

Washable MERV 3 filters protect both airstreams of the Fantech SHR 700. For better filtration of outdoor air, Fantech offers MERV 8 or MERV 13 filters; according to the brochure, the MERV 13 captures 50% of particles from 0.3 to 1 micron. A finer filter adds resistance: we take that into account when balancing.

Fantech's manual calls for checking and cleaning the filters once a month, or sooner if they look dirty. The motors are factory balanced and lubricated for life: they require no maintenance.

Warranty

Fantech warranty: core warranted for life, motor and electrical components warranted for 3 years. The manual points out that connecting a clothes dryer, a kitchen range hood or a central vacuum to the unit voids the warranty.

Installation by AirGreen in Greater Montreal

Before proposing the Fantech SHR 700, we determine the outdoor airflow your premises need from the building's ventilation calculation. In a large home, we apply the room-by-room method of the CSA F326 standard. We also check the space, the electrical supply and the duct routing.

The job ends with balancing: we measure the fresh air and the exhaust air and adjust them to the calculated airflow. That way you know exactly what your HRV delivers, and we can compare those measurements from one year to the next during maintenance.

We work in Montreal, Laval, Longueuil, the North Shore and the South Shore. For a free quote, call 514 316-2973 or write to sales@airgreen.ca.