Fantech HRV SHR 800 Air Exchanger | Montreal, Laval, Longueuil, South Shore and North Shore

In stock
SKU: SHR 800
HRV
01 · Good to know

What you should know about this one

Published, verifiable facts, not brochure claims.

158 lb795 cfm at 158 lb, versus 215 lb for the SHR 700

The brochure gives 795 cfm at 0.4 in for the SHR 800, weighing 158 lb, versus 720 cfm and 215 lb for the SHR 700. The manual shows a port layout different from the SHR 450, 700 and 1200.

BPMRecirculation defrost available with the BPM module

Standard defrost shuts down the supply fan. With the optional BPM bypass module, offered on SHR models only, a motorized damper closes the fresh-air intake so indoor air circulates through the core without creating negative pressure.

ExhaustIt defrosts by pausing the fresh air for a few minutes

In cold weather, the supply fan stops for a few minutes while the exhaust keeps running, so warm indoor air thaws the core. During the cycle the house is briefly under negative pressure; if you have a fireplace or a naturally vented combustion appliance, mention it to our estimator.

HRVIt recovers heat, not moisture

Excess moisture leaves the house. In Québec, that's the right choice in most cases: in winter, a home almost always has too much humidity, not too little.

LifetimeThe core warranty

The core does the work and is the most expensive part to replace. Motors and parts: 3 years.

02 · Installation

What it needs on site

Side connectionSide ports
Condensate drainRequired
158 lbUnit weight
120 VPower supply

In a condo with no floor drain, or with little ceiling clearance, we usually look at a side-port model instead. Our estimator checks the location, the drain and the duct route before ordering.

Complete spec sheetData and cited sources
Type
HRV
Connection
Side ports
Condensate drain
Required
Defrost cycle
Exhaust only (supply fan off)
Filters
Washable MERV 3 filters (exhaust and supply); MERV 8 or MERV 13 upgrade
Weight
158 lb
Power supply
120 V
Warranty — core
Lifetime
Warranty — motors
3 years
Warranty — parts
3 years
Spec sheet (French)
PDF
Spec sheet (English)
PDF

The manufacturer doesn't publish an efficiency at −25 °C for this model; we don't make one up.

Talk to an HVAC technician before you choose

We calculate the airflow room by room, check the location and the drain, and give you an installed price. Balancing is measured at commissioning, not estimated.

Fantech SHR 800: more airflow than the SHR 700, for less weight

The Fantech SHR 800 is the surprise of the SHR series: it delivers more air than the SHR 700 while being lighter. This light commercial heat recovery ventilator suits offices, shops and multipurpose rooms where the ceiling space or the structure limits the allowable load.

The Fantech SHR 800 is not listed in the HVI directory, which rates residential units. It has no certified net airflow to compare with a residential model: instead, we start from the building's ventilation calculation to confirm that it is a fit.

795 cfm for 158 lb

The brochure gives 795 cfm at 0.4 in. for the SHR 800, with a weight of 158 lb, versus 720 cfm and 215 lb for the SHR 700. The manual gives it a connection layout different from that of the SHR 450, 700 and 1200: it shares the SHR 1400's layout. According to Fantech's manual, S stands for side connections (Side Ducting), H for heat recovery and R for the remote control option; the number gives the airflow class at 0.4 in.

The best electrical efficiency in the series

With 636 W and 5.3 A on 120 V, the SHR 800 delivers about 1.3 cfm per watt at 0.4 in. according to the brochure, the best figure among the SHR units. Its sensible effectiveness in heating is 55%, based on the core's AHRI 1060 data. For a unit that runs all day in a business, the difference in consumption shows up on the bill.

Defrost

Standard defrost shuts off the fresh air fan while the exhaust air defrosts the core. With the optional BPM bypass module, available only on SHR units, a motorized damper closes the fresh air intake as soon as outdoor air reaches −5 °C: indoor air then circulates through the core to warm it, and the unit does not create negative pressure.

Installation: connections and drain

The Fantech documents we have do not specify the SHR 800 cabinet dimensions, and its connection layout differs from the SHR 700's: we confirm these points with the manufacturer before installation. The fan motors and the core are mounted on removable sliding rails, and the door panels are reversible so they open on the side where service is done. A drain is required. Condensate, including during defrost, must flow to a drain or a condensate pump, with a P-trap in the hose to keep odours from coming back up. The unit and its condensate hoses must be located in a heated space, above freezing.

Filter maintenance

The Fantech SHR 800 comes with washable MERV 3 filters on the fresh air and stale air streams. Fantech describes them as starter filters, able to capture about 20% of particles from 3 to 10 microns. A MERV 8 filter captures 70% of those particles and a MERV 13, 95%: that is the upgrade to consider near a busy street.

Fantech's manual calls for checking and cleaning the filters once a month, or sooner if they look dirty. The motors are factory balanced and lubricated for life: they require no maintenance.

Warranty

Fantech warrants the SHR 800 core for life (limited warranty), and the motor and electrical components for 3 years.

Installation by AirGreen in Greater Montreal

For an office, a shop or a multipurpose room, we start from the building's ventilation calculation: how the space is used, the number of occupants and the floor area. For a large home, we do the room-by-room calculation according to the CSA F326 standard. That figure tells us whether the Fantech SHR 800 is the right size or whether a smaller or larger model is needed. We also look at where to place the fresh air intake and the stale air outlet, far enough apart that the exhaust air is not drawn back in.

Once the unit is installed, we balance the fresh air and the exhaust air to the calculated airflow, with measurements taken on the ducts. A poorly balanced HRV uses more energy and ventilates less well than planned: it is the step we never skip.

We install in Montreal, Laval, Longueuil, the North Shore and the South Shore. Ask for a free quote at 514 316-2973 or write to us at sales@airgreen.ca.