Lifebreath 1200 DD HRV Air Exchanger | Montreal, Laval, Longueuil, South Shore and North Shore
What you should know about this one
Published, verifiable facts, not brochure claims.
DDDD version: indoor-air bypass for defrost
The DD suffix (Damper Defrost) marks the damper version: a supply bypass routes indoor air to the cores during defrost. The 1200 FD, in the same cabinet, has no damper and interrupts supply air while exhaust air defrosts.
30 A120 V circuit with 30 A maximum protection
Its two 1/2 HP PSC motors draw 18.8 A in total at high speed. The sheet gives a minimum circuit ampacity (MCA) of 23.5 A and a maximum overcurrent protection (MOP) of 30 A, to plan at the electrical panel.
DamperIt defrosts with indoor air
In cold weather, a motorized damper closes the outdoor air intake and recirculates indoor air through the core to thaw it. During the cycle, no outdoor air comes in through the unit.
HRVIt recovers heat, not moisture
Excess moisture leaves the house. In Québec, that's the right choice in most cases: in winter, a house almost always has too much humidity, not too little.
15 yearsThe core warranty
The core does the work and is the most expensive part to replace. Motors and parts: 2 years.
What it needs on site
In a condo with no floor drain, or with little ceiling clearance, we usually look at a side-port model instead. Our estimator checks the location, the drain and the duct route before ordering.
Complete spec sheetData and cited sources
- Type
- HRV
- Connection
- Side ports
- Condensate drain
- Required
- Defrost cycle
- Recirculation (motorized damper)
- Filters
- Washable MERV 6 filters (exhaust and supply); MERV 13 upgrade (65-195-6R)
- Dimensions (L × D × H)
- 33.25 × 42 × 32.25 in
- Weight
- 253 lb
- Power supply
- 120 V
- Warranty — core
- 15 years
- Warranty — motors
- 2 years
- Warranty — parts
- 2 years
- Spec sheet (French)
- Spec sheet (English)
The manufacturer doesn't publish an efficiency at −25 °C for this model; we don't make one up.
Talk to an HVAC technician before you choose
We assess your needs on site, check the location and the drain, and give you an installed price. Balancing is measured at commissioning, not estimated.
Lifebreath 1200 DD: three cores, 120 V and a defrost damper
When an office, a school or a store needs more fresh air than the 700 cfm of a 700 DD, the Lifebreath 1200 DD takes over: Lifebreath's table rates it at 1,200 cfm nominal at 0.5 in., and its blowers are rated at 1,200 cfm (566 L/s) free air delivery. This three-core commercial heat recovery ventilator still runs on 120 V, but its maximum overcurrent protection goes up to 30 A, twice that of the 700.
The 1200 DD does not appear in the HVI directory; no net airflow or efficiency is therefore certified for it the way it would be for a residential HRV. In a house, the principal ventilation falls under article 9.36.3.9 of the Québec Construction Code, which requires a unit tested to CAN/CSA-C439 and certified by HVI or by another body accredited by the Standards Council of Canada, or else tested to ANSI/AHRI-1061 and certified by a body the Code designates. For a large home, we check that certification before any quote.
DD version: indoor-air bypass for defrost
DD stands for Damper Defrost. Below −3 °C (27 °F) outside, the defrost timer kicks in: a motorized damper opens the defrost port and closes the outdoor air inlet, so the bypass sends indoor air through the cores. Lifebreath even allows the outdoor air port and the defrost port to be swapped in the field, by switching two wires on the circuit board (T37, red, and T39, yellow). The 1200 FD, in the same cabinet, does not have this fifth port: it stops its supply fan instead while the exhaust air defrosts.
At 1,200 cfm, the gap between the two versions carries more weight. With the FD, exhaust continues without fresh air during each defrost, while the DD keeps the supply running with room air. It is a difference we look at closely for an enclosed space.
A 120 V circuit with 30 A protection
The two double-shaft 1/2 HP PSC motors (1,625 rpm) draw 9.4 A each, for 18.8 A on high speed for the whole unit. The model spec sheet and the sales table agree on 23.5 A of minimum circuit ampacity (MCA) and 30 A of maximum overcurrent protection (MOP): the circuit, a dedicated one, is planned at the panel. The manual specifies that this circuit must handle the full load amperage (FLA) shown on the unit's nameplate.
Efficiency and power use
Heat is recovered in three 68-222 cores, AHRI 1060 certified, which form three modular counter-flow sections crossed in a single pass. Lifebreath publishes the temperature effectiveness as a curve, with exhaust air at 40% relative humidity; its sales table lists 58% at 0 °C, but not the airflow at which that figure was obtained: a benchmark rather than a rating. On high speed, the unit uses 2,256 W in total according to the spec sheet: we therefore set the speed to the airflow the space needs, instead of leaving it on maximum by default.
Installation: connections, weight and drain
Four rectangular 20 × 8 in. collars (508 × 200 mm) take the ducts. According to the sales table, the cabinet is 32.25 in. high, 33.25 in. wide and 42 in. deep; it weighs 253 lb, or 303 lb shipping. It sits on support brackets hung from threaded rods, not supplied; the manual also describes mounting on a frame of rods and U-channels, or on a wood or metal curb, with vibration isolators to be supplied by others. The drain, which is mandatory, connects to two outlets (1/2 in., or 12 mm, OD). Prepainted, the 22-gauge G60 galvanized steel is insulated with foil facing where exterior condensation must be prevented. Allow 30 in. (762 mm) of service clearance.
Controls and access
The built-in microprocessor circuit board controls the three speeds, and its interlock contacts are used to connect the unit to another piece of equipment. The front and back doors, with an electrical box that goes on either side, give the installer the choice of duct direction; the unit is field reversible, and the blowers slide out for service. Lifebreath states that it conforms to CSA and UL standards.
Filter care
For filtration, washable MERV 6 filters protect the fresh air and the stale air of the Lifebreath 1200 DD: they come out, get washed and go back in place. A MERV 13 option (part 65-195-6R) can be added if the outdoor air in the area is heavily loaded. Specific to the DD, the manual lists another maintenance point: the damper shaft, on the side opposite its motor, needs a little lithium grease every two or three years.
Warranty
Lifebreath warrants the 1200 DD heat recovery core for 15 years and replacement parts for 2 years; the spec sheet gives no separate term for the motors, which therefore follow the parts warranty.
Installation by AirGreen in Greater Montreal
Before pricing a 1200 DD, we assess on site how much fresh air the building calls for: use and number of occupants for commercial premises, and for a large home, the home's ventilation needs (bedrooms, bathrooms, kitchen, basement). We then compare that airflow with the airflow curve of the Lifebreath 1200 DD and with the static pressure of your duct system.
For start-up, all mechanical systems run on high speed. We follow the manual's method: a small hole of about 3/16 in. in each duct, 3 ft downstream of any elbow and 1 ft upstream, then a reading with a Pitot tube connected to a manometer. Multiplied by the cross-section of the duct, the measured velocity gives the actual airflow, and the stronger airstream is adjusted with a damper installed on site until the fresh air and the exhaust air are balanced.
Our teams work in Montreal, Laval, Longueuil, the North Shore and the South Shore, under AirGreen's RBQ licence 5645-9605-01. For a 1200 DD, ask for a quote at 514 316-2973 or by email at sales@airgreen.ca: we will call you back.
