Lifebreath 1200 Pool HRV Air Exchanger | Montreal, Laval, Longueuil, South Shore and North Shore
What you should know about this one
Published, verifiable facts, not brochure claims.
PoolPool version: elastomeric insulation, BC02 control included
Designed for indoor pools, the 1200 Pool has an elastomeric-insulated cabinet, whereas the 1200 DD uses foil-faced insulation. The BC02 basic control is included and defrost uses an indoor-air bypass.
18.8 A120 V circuit sized from the nameplate
Its two 1/2 HP PSC motors draw 18.8 A in total at high speed. The circuit is sized from the unit's nameplate. Plan for at least 30 in (760 mm) of clearance in front of the unit for service.
DamperIt defrosts with indoor air
In cold weather, a motorized damper closes the outdoor air intake and recirculates indoor air through the core to thaw it. During the cycle, no outdoor air comes in through the unit.
HRVIt recovers heat, not moisture
Excess moisture leaves the house. In Québec, that's the right choice in most cases: in winter, a house almost always has too much humidity, not too little.
15 yearsThe core warranty
The core does the work and is the most expensive part to replace. Motors and parts: 2 years.
What it needs on site
In a condo with no floor drain, or with little ceiling clearance, we usually look at a side-port model instead. Our estimator checks the location, the drain and the duct route before ordering.
Complete spec sheetData and cited sources
- Type
- HRV
- Connection
- Side ports
- Condensate drain
- Required
- Defrost cycle
- Recirculation (motorized damper)
- Filters
- Washable MERV 6 filters (exhaust and supply); MERV 13 upgrade (65-195-6R)
- Dimensions (L × D × H)
- 33.25 × 42 × 32.25 in
- Weight
- 265 lb
- Power supply
- 120 V
- Warranty — core
- 15 years
- Warranty — motors
- 2 years
- Warranty — parts
- 2 years
- Spec sheet (French)
- Spec sheet (English)
The manufacturer doesn't publish an efficiency at −25 °C for this model; we don't make one up.
Talk to an HVAC technician before you choose
We assess your needs on site, check the location and the drain, and give you an installed price. Balancing is measured at commissioning, not estimated.
Lifebreath 1200 Pool: three cores for large pool rooms
The Lifebreath 1200 Pool is the pool version of Lifebreath's 1200: a heat recovery ventilator designed for larger pool rooms, such as those of a sports club, a hotel, a condo building or a school. Its blowers reach 1,200 cfm (566 L/s) free air delivery, and three aluminum cores recover the heat from the humid air before it is sent outside.
The 1200 Pool is not listed in the HVI directory: there is therefore no certified net airflow and no published recovery efficiency for it the way there would be for a residential HRV. To choose it, what counts is the room and its pool, as described below.
Pool version: elastomeric insulation and BC02 control
Designed for indoor pools, the 1200 Pool gets elastomeric insulation, where the 1200 DD makes do with foil facing. The BC02 basic control comes with the unit, and for defrost, a bypass circulates indoor air through the cores below −3 °C (27 °F) outside. Lifebreath describes it as a more economical option than other dehumidification installations.
The principle stays simple: the humid room air goes out, the drier outdoor air comes in, and the core transfers part of the heat from one to the other. With the dehumidistat control described in the manual, the unit runs in recirculation, with the exhaust fan off and outdoor air blocked by a damper, then switches to ventilation when humidity rises above the setpoint. The manual specifies, however, that this dehumidistat only works below 15 °C (59 °F) outside: in a large pool, we therefore check whether a dehumidifier needs to be added. It also requires a room heated by an appliance independent of the pool water, a pool and room operated without interruption as originally designed, and full commissioning after installation, control included.
Dedicated circuit and 30 in. clearance
The two PSC motors, 1/2 HP and 1,625 rpm, draw 9.4 A each, for 18.8 A in all on high speed, at 120 V; the circuit is sized from the unit's nameplate. In front of the unit, keep at least 30 in. (760 mm) clear for service.
Efficiency and power use
Three 68-222 cores, AHRI 1060 certified, arranged in three counter-flow sections, form the heart of the unit. Lifebreath publishes the temperature effectiveness as a curve, taken with exhaust air at 40% relative humidity; only the sales table puts forward a figure, 58% at 0 °C, with no test airflow. On high speed, power use climbs to 2,256 W: we set the speed to the airflow the room actually needs.
Installation: dimensions, connections and drain
The 1200 Pool is 33.25 in. wide, 42 in. deep and 32.25 in. high, and weighs 265 lb (315 lb shipping). It hangs from brackets and threaded rods, not supplied, or sits on vibration isolation pads. The connections are rectangular, and the spec sheet dimensions the defrost port at 20 × 8 in. (508 × 203 mm). The drain is required, through two 1/2 in. (12 mm) OD outlets; trap and tubing run below the bottom of the door, sloping 1/4 in. per foot away from the unit. The cabinet is prepainted G60 galvanized steel, and its side access panel can be fitted on either side on site.
Controls and access
The built-in microprocessor circuit board runs three speeds and, through its interlock contacts, can be tied to another piece of building equipment. The supplied BC02 serves as the main control, and the manual accepts only one per installation. Front and back access doors, an electrical box placed at the front or back to suit the duct direction, and blowers that slide out of the cabinet round out the package; Lifebreath states that it is field reversible, and it meets CSA and UL standards.
Filter care
The Lifebreath 1200 Pool protects the fresh air and the stale air with washable MERV 6 filters, to be cleaned in cold water with a mild detergent. Depending on use, cleaning the filters and cores comes around every one to two months at most often, and at least once every six months. A MERV 13 version of these filters is also available. Finally, the defrost damper needs a little lithium grease on its shaft, opposite the motor, at intervals of two or three years.
Warranty
Lifebreath warrants the 1200 Pool heat recovery core for 15 years and replacement parts for 2 years; the spec sheet gives no separate term for the motors, which therefore follow the parts warranty.
Installation by AirGreen in Greater Montreal
For a pool room, we assess the ventilation needs of the room and its pool on site. Lifebreath's manual sets the airflow from the water surface area, the water temperature and the target humidity in the room; a spa or hot tub is added at 10 cfm per square foot of surface, or 250 cfm for a 25 sq. ft spa in the manual's example. The 1200 Pool is only chosen if the total falls within its operating range.
When the unit supplies the room through a duct system fully dedicated to it, the manual adds that make-up heat is usually necessary, for example an electric in-line duct heater, to bring the fresh air back up to room temperature. After installation, we set speeds and dampers on high speed until the fresh air and exhaust air are balanced; for a colder climate, the manual also provides a more aggressive defrost, with DIP switch 8 set to ON.
Our teams work in Montreal, Laval, Longueuil, the South Shore and the North Shore, under AirGreen's RBQ licence 5645-9605-01. For a large pool room, ask for a quote at 514 316-2973 or write to sales@airgreen.ca: we will call you back.
