Lifebreath 650 DD HRV Air Exchanger | Montreal, Laval, Longueuil, South Shore and North Shore

In stock
SKU: 650 DD
HRV
01 · Good to know

What you should know about this one

Published, verifiable facts, not brochure claims.

5 portsA fifth 20 × 8 in port for defrost air

The 650 DD (Damper Defrost) adds a 20 × 8 in port to the four connections of the 650 FD, through which a supply bypass routes indoor air to the core during defrost. The 650 FD has no such port: it interrupts supply air while exhaust air defrosts the core.

20 × 8 in20 × 8 in rectangular connections

Lifebreath gives a standard 20 × 8 in duct size, but its sheet also lists 26 × 8 in for the stale-air intake: we check that dimension on the unit before ordering the transitions. The low-profile cabinet is meant for installation above a suspended ceiling, on brackets and threaded rods (not included).

DamperIt defrosts with indoor air

In cold weather, a motorized damper closes the outdoor air intake and recirculates indoor air through the core to thaw it. During the cycle, no outdoor air comes in through the unit.

HRVIt recovers heat, not moisture

Excess moisture leaves the house. In Québec, that's the right choice in most cases: in winter, a house almost always has too much humidity, not too little.

15 yearsThe core warranty

The core does the work and is the most expensive part to replace. Motors and parts: 2 years.

02 · Installation

What it needs on site

Side connectionSide ports
Condensate drainRequired
270 lbUnit weight
54 × 42 × 24.75 inLength × depth × height
120 VPower supply

In a condo with no floor drain, or with little ceiling clearance, we usually look at a side-port model instead. Our estimator checks the location, the drain and the duct route before ordering.

Complete spec sheetData and cited sources
Type
HRV
Connection
Side ports
Condensate drain
Required
Defrost cycle
Recirculation (motorized damper)
Filters
Washable MERV 6 filters (exhaust and supply); MERV 13 upgrade (65-195-6R)
Dimensions (L × D × H)
54 × 42 × 24.75 in
Weight
270 lb
Power supply
120 V
Warranty — core
15 years
Warranty — motors
2 years
Warranty — parts
2 years
Spec sheet (French)
PDF
Spec sheet (English)
PDF

The manufacturer doesn't publish an efficiency at −25 °C for this model; we don't make one up.

Talk to an HVAC technician before you choose

We assess your needs on site, check the location and the drain, and give you an installed price. Balancing is measured at commissioning, not estimated.

Lifebreath 650 DD: a low-profile HRV for suspended ceilings, with a defrost port

The Lifebreath 650 DD is a commercial heat recovery ventilator with a low-profile cabinet, which Lifebreath designed for installation above a suspended ceiling. At 24.75 in. high, it is aimed at open-plan offices, stores and classrooms where the mechanical equipment has to disappear into the ceiling space. Its centrifugal blowers are rated at 950 cfm (448 L/s) free air delivery; in its commercial table, Lifebreath lists it at 630 cfm nominal.

This is a commercial unit: the Lifebreath 650 DD does not appear in the HVI directory, and no net airflow or efficiency is rated there for it. In a residence, article 9.36.3.9 of the Québec Construction Code requires the dwelling's principal ventilation to rely on a unit whose efficiency is certified to a test standard the Code recognizes: we take this into account before recommending it.

A fifth connection for defrost air

The 650 DD (Damper Defrost) adds a 20 × 8 in. port to the four connections of the 650 FD. When it is colder than −3 °C (27 °F) outside, a timer starts the defrost: a bypass then sends indoor air through the core via this port, for 4 minutes in every 30 minutes of operation at the factory setting. The 650 FD has no such port; on that model, the fresh air is shut off while the exhaust air defrosts the core, and exhaust continues with no fresh air to make up for it.

This fifth connection takes up a bit more room above the ceiling. In the spec sheet drawings, the defrost air inlet is marked DD only: we place it from the very first duct layout.

The stale-air intake and the other connections

Three rectangular connections are 20 × 8 in., and the spec sheet gives 26 × 8 in. for the stale-air intake: we check this dimension on the unit before ordering the transitions. Its access doors, front and back, make the unit field reversible and let you choose the duct direction.

Efficiency and power use

The core is modular, in six counter-flow aluminum sections, with AHRI 1060 certified HEX cores. Lifebreath publishes the temperature effectiveness as a curve, with no figure tied to a specific airflow. The brand's commercial table does, however, list 84% at 0 °C, without stating the test airflow, and credits the 650 with six cores and two passes, where the 455 and 700 in the same table have two and one, for 58 to 59%. In each airstream, a double-shafted motor turns two blowers positioned in suction, which, according to Lifebreath, provides better air movement.

The two three-speed 1/4 HP PSC motors (1,625 rpm) use 912 W in total on high speed according to the spec sheet. The spec sheet sets the minimum circuit ampacity (MCA) at 9.5 A and the maximum overcurrent protection (MOP) at 15 A, on 120 V. Motor current: per the unit's nameplate, since Lifebreath's documents do not all give the same value.

Installation: dimensions, weight and drain

The cabinet measures 54 in. wide, 42 in. deep and 24.75 in. high, and weighs 270 lb (342 lb shipping): the structure that carries it has to be planned accordingly. Lifebreath sets it on support brackets hung from threaded rods, which are purchased separately. A drain is required, with 1/2 in. OD connections. Made of 22-gauge G60 prepainted galvanized steel, the cabinet resists corrosion; foil-faced insulation protects the exposed walls against exterior condensation. Lifebreath calls for 30 in. of service clearance, and the blowers slide out of the cabinet.

Circuit board and standards

The three speeds are run by a microprocessor circuit board, whose built-in interlock contacts are used to link the unit to other building equipment. Lifebreath states that the units on this spec sheet conform to CSA and UL standards.

Filter care

Day to day, servicing the Lifebreath 650 DD comes down to its washable MERV 6 filters, on the fresh air and on the stale air, which are washed in cold water with a mild detergent. A clogged filter reduces airflow. It also accepts Lifebreath's MERV 13 filters, part 65-195-6R, for tighter filtration of the incoming air.

Warranty

Manufacturer's warranty: 15 years on the 650 DD core and 2 years on replacement parts. Lifebreath does not publish a separate warranty for the motors.

Installation by AirGreen in Greater Montreal

For an open-plan office, a store or a school, we assess the premises' ventilation needs on site based on their use and occupancy; for a large residence, we count the bedrooms, bathrooms, kitchen and basement. We then compare those needs with the Lifebreath 650 DD airflow curve and with the static pressure your ducts will impose.

Above a suspended ceiling, several of the manual's instructions matter. The unit must be installed level so the condensate drains, and the manual provides for vibration isolators, not included, between the unit and its structure. On the 650, the P-trap can be formed by looping the 1/2 in. drain hose, which must stay protected from freezing. Outside, each hood carries a bird screen with mesh of 1/4 in. or more, and the air through it must not exceed 1,000 ft/min (5.08 m/s) to limit water and debris getting in: we size the hoods to the chosen airflow.

On start-up day, we balance the air coming in and the air going out, with the unit on high speed, as Lifebreath requires.

Our team, under AirGreen's RBQ licence 5645-9605-01, serves Montreal, Laval, Longueuil, the North Shore and the South Shore. Ask for a quote: 514 316-2973 or sales@airgreen.ca. We will call you back.