Lifebreath 700 Pool HRV Air Exchanger | Montreal, Laval, Longueuil, South Shore and North Shore
What you should know about this one
Published, verifiable facts, not brochure claims.
PoolPool version: elastomeric insulation, BC02 control included
Designed for indoor pools, the 700 Pool has an elastomeric-insulated cabinet, whereas the 700 DD uses foil-faced insulation. The BC02 basic control is included and defrost uses an indoor-air bypass.
30 inHung from rods or set on vibration isolation pads
It hangs on brackets and threaded rods (not included) or sits on vibration isolation pads. Plan for at least 30 in (760 mm) of clearance in front of the unit for service; the side access panel can be switched to either side in the field.
DamperIt defrosts with indoor air
In cold weather, a motorized damper closes the outdoor air intake and recirculates indoor air through the core to thaw it. During the cycle, no outdoor air comes in through the unit.
HRVIt recovers heat, not moisture
Excess moisture leaves the house. In Québec, that's the right choice in most cases: in winter, a house almost always has too much humidity, not too little.
15 yearsThe core warranty
The core does the work and is the most expensive part to replace. Motors and parts: 2 years.
What it needs on site
In a condo with no floor drain, or with little ceiling clearance, we usually look at a side-port model instead. Our estimator checks the location, the drain and the duct route before ordering.
Complete spec sheetData and cited sources
- Type
- HRV
- Connection
- Side ports
- Condensate drain
- Required
- Defrost cycle
- Recirculation (motorized damper)
- Filters
- Washable MERV 6 filters (exhaust and supply); MERV 13 upgrade (65-195-6R)
- Dimensions (L × D × H)
- 33.25 × 29 × 32.25 in
- Weight
- 180 lb
- Power supply
- 120 V
- Warranty — core
- 15 years
- Warranty — motors
- 2 years
- Warranty — parts
- 2 years
- Spec sheet (French)
- Spec sheet (English)
The manufacturer doesn't publish an efficiency at −25 °C for this model; we don't make one up.
Talk to an HVAC technician before you choose
We assess your needs on site, check the location and the drain, and give you an installed price. Balancing is measured at commissioning, not estimated.
Lifebreath 700 Pool: an HRV built for the humid air of an indoor pool
An indoor pool produces moisture all the time. The Lifebreath 700 Pool is an HRV that Lifebreath designed for these spaces: it exhausts the humid air of the pool room and replaces it with outdoor air preheated in the core. With blowers rated at 700 cfm (329 L/s) free air delivery, it suits the pool room of a large home, a spa, or a small condo or club pool.
Like every commercial unit in the range, the 700 Pool has no HVI rating, so no certified net airflow or efficiency in the residential sense. Its airflow is chosen with the method Lifebreath gives for pools, described below.
What sets the pool version apart
Where the 700 DD gets foil-faced insulation, the 700 Pool cabinet is insulated with elastomeric insulation. The BC02, a basic control, is supplied, and for defrost, a bypass sends indoor air through the cores, as on the DD models; the defrost timer kicks in as soon as it is colder than −3 °C (27 °F) outside. Lifebreath states that, for a pool, this version costs less than other dehumidification installations. According to Lifebreath's manual, however, dehumidistat control only works when it is below 15 °C (59 °F) outside: we therefore check case by case whether a dehumidifier is needed as well.
In winter, outdoor air holds very little moisture. Swapping it for the moisture-laden air of the pool room helps keep humidity under control, while the core recovers part of the heat from the exhaust air. The manual also sets three conditions: the room must have its own heating appliance, which does not draw its heat from the pool water; the pool and its room must be operated continuously as originally designed; the unit must be fully commissioned after installation, including the control and drainage through the pans.
Suspended or on vibration isolation pads
The 700 Pool hangs from support brackets mounted on threaded rods, which Lifebreath does not supply, unless it sits on vibration isolation pads. Allow at least 30 in. (760 mm) of clearance in front of the unit for service; the side access panel can be switched in the field, for service from the left or the right. The manual also wants the unit installed level, so the water drains, in a heated space that never falls below 16 °C (60 °F).
Efficiency and power use
Two 68-222 cores, AHRI 1060 certified, in two counter-flow sections, handle heat recovery. The spec sheet shows the temperature effectiveness as a curve, with no tabulated value, for exhaust air at 40% relative humidity; Lifebreath's sales table lists 59% at 0 °C, with no test airflow. Its two PSC motors (single shaft, 1/4 HP, 1,450 rpm) draw 4.5 A each, 9 A in total on high speed, for 1,032 W according to Lifebreath, on a 120 V supply. Lifebreath's spec sheets and sales table contradict each other on the circuit; electrical values: per the unit's nameplate.
Installation: dimensions, connections and drain
At 33.25 in. wide, 29 in. deep and 32.25 in. high, the cabinet weighs 180 lb (231 lb shipping). The ducts connect to rectangular 14 × 8 in. openings (356 × 203 mm). The drain, which is mandatory, starts from two connections (1/2 in. or 12 mm, OD): the manual calls for cutting two lengths of 1/2 in. hose, not supplied, forming a P-trap with the tee connector, then pouring a cup of water into the pan once the drain is connected. The cabinet is prepainted G60 galvanized steel, and the electrical box moves from front to back to suit the duct direction.
Controls and access
The three speeds run through a microprocessor circuit board, fitted with interlock contacts to connect the HRV to other equipment. The BC02 supplied with the unit overrides a 99-500 three-speed control whenever its dehumidistat is working or it is set to high speed, and only one main control is allowed per system, the manual specifies. The front and back access doors and the blowers, which slide out of the cabinet, make service easier; the units conform to CSA and UL standards, according to Lifebreath.
Filter care
Routine maintenance on the Lifebreath 700 Pool comes down mostly to the filters: washable MERV 6 filters on the fresh air and on the stale air. The manual has them cleaned with cold water and a mild detergent, sometimes every one or two months and at least every six months, and rules out harsh chemicals, which can corrode the unit. Lifebreath also offers a MERV 13 version of these filters.
Warranty
Manufacturer's warranty: 15 years on the 700 Pool core and 2 years on replacement parts. Lifebreath does not publish a separate warranty for the motors.
Installation by AirGreen in Greater Montreal
For a pool room or a spa, we assess the room's ventilation needs on site. Lifebreath's manual, for its part, sets the airflow from the pool itself: an evaporation rate, taken from the air and water temperatures and the relative humidity, multiplied by a flow rate factor that depends on the indoor and outdoor temperatures, gives cfm per square foot of water surface, which is then multiplied by the pool's surface area. Its example, a 512 sq. ft pool, comes to 573 cfm, below the 700 Pool's 700 cfm nominal. Outside, the fresh-air intake and the stale-air outlet go 10 ft (3 m) or more apart, so the exhaust air is not drawn back in.
Once the unit is in place, we balance the fresh air and the exhaust air on high speed, with measurements taken on the ducts; the manual places the Pitot tube at least 18 in. from the blower or any elbow. For the duct system, Lifebreath recommends galvanized metal ducts, fully insulated and fitted with an integral vapour barrier wherever they pass through an unheated space.
We install this HRV in Montreal, Laval, Longueuil, the North Shore and the South Shore, under AirGreen's RBQ licence 5645-9605-01. Ask for a quote at 514 316-2973 or write to us at sales@airgreen.ca: we will call you back.
