Galvanized Side Take-Off
The fitting that starts a round branch from the side of a trunk duct or plenum.
AirGreen codeAG-VC-00502
514 316-2973 · sales@airgreen.ca
Quick facts
The galvanized side take-off, or simply take-off, starts a round branch off the side of a main duct (trunk) or a plenum. It is the fitting through which air leaves the main system to go to a room, a floor register or a wall grille.
Adding or redoing a forced-air branch
In a forced-air system, each room is fed by its own branch. During an addition, a basement finish or the replacement of a furnace with a central heat pump, branches often have to be added or moved. The side take-off installs on an existing duct without taking the system apart.
Six diameters
Available in 4, 5, 6, 8, 10 and 12 in. The size is the diameter of the round branch; it depends on the airflow needed in the room and the length of the branch.
Installation steps
- Trace the opening by holding the take-off against the main duct.
- Cut with tin snips and deburr the edge.
- Insert the take-off and fasten it with sheet metal screws.
- Seal the whole joint with mastic or aluminum tape.
To be able to balance the room, add a round damper on the branch or go with the side take-off with built-in damper.
Installed by AirGreen across Greater Montréal
We add, move and balance forced-air branches in Montréal, Laval, Longueuil, on the South Shore and on the North Shore. RBQ licence 5645-9605-01, subcategory 15.8 Ventilation. For availability or a quote, call us at 514 316-2973 or email sales@airgreen.ca with the diameter and the number of take-offs.
Where every branch begins
Every heated or cooled room is fed by a branch; the side take-off is where that branch leaves the trunk.
- Supply branch take-offs on a forced-air trunk
- Adding a branch to an enlarged or renovated room
- Branch take-off on a furnace or central heat pump plenum
- Connecting round ducts to an existing rectangular duct
6 sizes, one page
Each size has its own AirGreen code. Tap a row to select it.
| Dimensions | AirGreen code |
|---|---|
| 4 in | AG-VC-00501 |
| 5 in | AG-VC-00502 |
| 6 in | AG-VC-00503 |
| 8 in | AG-VC-00504 |
| 10 in | AG-VC-00505 |
| 12 in | AG-VC-00506 |
Diameter of the round branch.
Specifications
From the manufacturer’s documentation. A value the manufacturer does not publish is not listed.
What to know before installing
- The size is the diameter of the round branch leaving the take-off.
- Trace the opening using the take-off itself and cut the trunk cleanly.
- Screw the take-off to the duct and seal all around with mastic or foil tape.
- To adjust the branch airflow, add a damper or choose the version with a built-in damper.
You may also need
Galvanized Side Take-Off with Damper
Galvanized 90° Top Takeoff
Galvanized Round Damper (Balancing Key)
Galvanized Round Pipe – 60 in Length
Cleats for Galvanized Duct (C and S)
Galvanized Round End Cap
Galvanized Oval Duct – 60 in Length
90° Oval-to-Round Elbow (Oval Duct)Ventilation ductsSee all
Frequently asked questions
Where does a side take-off go?
On the side face of a trunk duct or plenum. The branch then leaves horizontally.
Side or top take-off?
The side take-off leaves from the side of the duct; the top take-off leaves from the top and turns 90°, handy for running along a joist. It depends on the room around the duct.
Do I need a damper?
It is recommended for balancing the rooms. Add a round damper on the branch or take the side take-off with damper.
Can you install it?
Yes. We add and rebuild forced-air branches across Greater Montréal, airflow balancing included.
Branches that start in the right place
Tell us the size and the quantity: we confirm availability and send you a quote. Or let our technicians install it for you.
Specifications from the manufacturer’s documentation, checked on October 7, 2026.
