SENVILLE R32 Top Discharge Central Heat Pump | 5 Tons - 60000 BTU

Share additional product information such as usage instructions, sizing guides, etc.

• Federal Rebate:
• Provincial Rebate: $
• Energy Star®: Non
• WiFi: En Option
• AHRI: 218338226
• Efficiency: 17.7 SEER
• Warranty (Compressor - Parts - Labor): 10-10-0
• Additional Warranty (10-10-10): Possible
• Voltage: 220V
• Sound Pressure Level (Outdoor): 60.0 dB(A)
• Gas (Freon): R-32

A high-capacity central system built around inverter technology, R-32, and a vertically discharging outdoor unit

The SENVILLE R32 Top Discharge 5-ton – 60,000 BTU central heat pump addresses a very different need from that of a small wall-mounted heat pump. It is intended for large homes, certain ducted multi-zone properties, and light commercial applications where the system must move a large volume of air while maintaining a relatively uniform temperature across multiple rooms.

At AirGreen, when we evaluate a central system replacement in Montreal, Laval, Longueuil, on the North Shore, or the South Shore, our first question is not simply whether the old unit was five tons. We must verify whether the ductwork, air returns, electrical supply, and the building’s heat losses still genuinely correspond to this capacity.

The combination presented on the AirGreen product sheet includes the SENTC-60TD-OG outdoor unit and the SENTC-60TD-IG indoor unit, associated with AHRI 218338226. It operates with R-32, uses a 220 V power supply, and offers optional WiFi.

Senville’s documentation describes this system as a 5-ton / 60,000 BTU central heat pump intended for large homes and light commercial applications. The brochure emphasizes its high airflow, its ability to maintain stable temperatures, and its variable-capacity operation.

60,000 BTU in the name, but 55,000 BTU/h in the technical table: an important distinction

The commercial designation refers to a 5-ton – 60,000 BTU system. However, it is important to look beyond the title.

In the brochure’s technical table, Senville lists a nominal cooling capacity of 55,000 BTU/h, with a modulation range of approximately 14,000 to 55,000 BTU/h.

This distinction deserves to be clearly explained.

In the HVAC industry, a system may be marketed in a five-ton capacity class while having a slightly different certified or nominal capacity depending on the exact combination of units and test conditions.

For the homeowner, the most useful information is therefore not simply “five tons.” Instead, we examine:

• the certified capacity of the exact combination;
• its modulation range;
• the airflow;
• the low-temperature heating capacity;
• the existing ductwork;
• the actual load of the building.

The AirGreen product sheet currently provided indicates a cooling capacity of 60,000 BTU. The attached technical brochure, for its part, indicates 55,000 BTU/h nominal. For a final quote, we therefore recommend referring to the exact combination SENTC-60TD-OG + SENTC-60TD-IG, AHRI 218338226, rather than inferring performance solely from the category name.

An inverter modulation that changes how a five-ton central system operates

The brochure specifies that the compressor is a Twin-Rotary DC Inverter, model KTQ420D41SN5A1 by GMCC.

This detail is central.

An older central air conditioner or heat pump could operate essentially at full capacity, then shut off when the setpoint was reached.

Here, the capacity can vary much more widely.

In cooling mode, the brochure shows a range of 14,000 to 55,000 BTU/h. In heating mode, the stated range is 13,400 to 55,000 BTU/h.

For a large home on the South Shore or in Laval, this means the unit does not need to continuously produce the equivalent of five tons when demand is moderate.

This modulation can promote:

• longer cycles;
• fewer abrupt temperature changes;
• more consistent airflow;
• better adaptation to intermediate loads;
• fewer full compressor starts.

However, it does not replace proper sizing. A five-ton heat pump remains a high-capacity piece of equipment, even when it can slow down.

Performance data: two sets of values that should not be mixed

The AirGreen product sheet provided with the product shows:

• SEER: 17.7
• HSPF: 8.0
• EER: 8.6

The attached technical brochure, meanwhile, shows:

• SEER2: 17.1
• EER2: 10.0
• HSPF2 Region 4: 8.7
• Nominal heating COP: 3.31

It would not be rigorous to arbitrarily choose one of these values and present the other as an error. The ratings may come from different certification versions, presentation methods, or combinations.

For a technical comparison with another central system, we recommend always using the data corresponding exactly to the AHRI number of the installed combination.

The key point remains that this is a high-capacity central inverter system, not a wall-mounted heat pump with a very high SEER2. The performance of a ducted system should be compared with other central systems in the same category.

Heating down to approximately -20 °C: what the brochure confirms

The AirGreen product sheet indicates heating operation down to -20 °C and classifies this model as non-Cold Climate.

The brochure confirms an outdoor heating range down to -4 °F, or approximately -20 °C.

This is an important difference compared with central heat pumps specifically designed and certified to maintain performance at -25 °C or -30 °C.

This SENVILLE can therefore play an important role in winter heating, but we do not present it as a -30 °C cold-climate heat pump.

According to the data on the AirGreen data sheet:

• capacity at -8 °C: approximately 30,400 BTU/h;
• capacity at -15 °C: approximately 30,000 BTU/h.

The brochure, for its part, provides several performance points:

• 57,000 BTU/h at 47 °F, or approximately 8 °C;
• 34,500 BTU/h at 17 °F, or approximately -8 °C;
• 40,000 BTU/h at 5 °F, or approximately -15 °C;
• 33,000 BTU/h at -4 °F, or approximately -20 °C.

These figures do not perfectly match the values currently displayed on the AirGreen data sheet. For us, this reinforces an important rule: before determining the heating capacity available at a specific temperature, the performance data for the actual AHRI combination being sold must be confirmed.

Why 30,000 to 40,000 BTU/h in extreme cold changes the sizing

Suppose a house has heat losses of 55,000 BTU/h at the design temperature.

A heat pump that still produces 30,000 or 35,000 BTU/h at that temperature will not cover the entire load on its own.

This does not mean it becomes useless.

On the contrary, it can continue to provide a significant portion of the heating while an auxiliary system makes up the difference.

In many central projects in Quebec, the goal is not necessarily to force the heat pump to cover 100% of the needs during the coldest hour of winter. The goal may be to maximize its operation during most of the season, then use supplemental heat when necessary.

An airflow of 1,740 CFM: the duct network must keep up

The documentation indicates an indoor airflow of up to 1,740 CFM, with an advertised minimum of approximately 750 CFM.

This is essential information for a five-ton installation.

A central system can function properly only if the duct network can actually carry its airflow.

During an AirGreen inspection, we pay particular attention to:

• main return size;
• plenum size;
• supply ducts;
• branches;
• filter cleanliness;
• restrictions;
• static pressure;
• the balancing of the grilles.

A high-capacity heat pump connected to undersized ductwork can be noisier, move less air than expected, and operate under unfavorable conditions.

A common example in Greater Montreal: the old system is five tons, but the ducts are not actually sized for five tons.

On central replacements, we sometimes encounter a paradoxical situation.

A house has had a five-ton air conditioner or heat pump for a long time, but the return air and some ducts look more like what would be expected from a smaller system.

The fact that the old unit operated for years does not prove that the installation was properly designed.

Before directly replacing five tons with five tons, we therefore analyze the existing distribution system.

This can help us avoid:

• excessively noisy airflow;
• high static pressure;
• poorly supplied rooms;
• uneven temperatures;
• lower efficiency than advertised performance.

Top Discharge: why the outdoor unit’s shape matters

The term Top Discharge means that the hot or cold air discharged by the condenser is expelled primarily upward.

This is a very common design on North American central systems.

It can be a good option when the unit is installed near a house or in a space where you want to avoid air being projected directly horizontally toward a patio, walkway, or neighboring wall.

However, this does not mean that the unit can be installed without clearance.

Sufficient space must be maintained around and above the unit to allow proper airflow and service access.

Compact outdoor dimensions for a five-ton capacity

The brochure gives the outdoor unit dimensions as approximately:

29 9/64 in × 29 9/64 in × 32 7/8 in

measuring approximately 29.14 × 29.14 × 32.88 in.

Its net weight is approximately 187 lb.

The square Top Discharge design is therefore quite different from some large, elongated side-discharge condensers.

For the installation, we check:

• the base;
• clearance around the machine;
• snow;
• disposal of defrost water;
• distance from windows;
• proximity to neighbors;
• technician access.

60 dB(A) outdoors

The documentation lists an outdoor sound level of 60 dB(A).

For a five-ton central system, this value deserves consideration from the planning stage.

In Montreal and Longueuil, some properties have relatively narrow side spaces. Placing a unit directly beneath a bedroom window or a few feet from a patio can make its operation much more noticeable.

We therefore seek a balance between:

• piping length;
• accessibility;
• aesthetics;
• clearance;
• noise;
• municipal regulations.

An indoor unit nearly 53 inches tall

The indoor unit measures approximately:

24.48 in × 21.03 in × 52.98 in

and weighs approximately 164 lb net.

This size is important when replacing a unit in a mechanical room already occupied by a water heater, electrical panel, or other equipment.

We must allow enough space not only to bring the unit in, but also to:

• connect the ducts;
• install or adapt the plenum;
• access the filter;
• service the fan;
• access the drain;
• open the service panels.

Indoor sound level of 44 to 52.5 dB(A)

The indoor fan produces approximately 44 dB(A) at low speed and 52.5 dB(A) at high speed.

In a properly installed central system, the indoor unit is generally located in a mechanical room, so this noise is less noticeable than with a wall-mounted unit located directly in the room.

However, poor duct design can transmit fan noise through the grilles. Once again, the system itself is only part of the final result.

The installation details that determine whether this 5-ton SENVILLE will actually deliver the expected performance

R-32: an important element of this new platform

The system uses R-32, with a stated factory charge of 3.4 kg, or approximately 119.9 oz.

The documentation also specifies an additional charge of approximately 0.52 oz per foot when necessary.

R-32 is an A2L refrigerant. Its handling therefore requires appropriate procedures and tools.

For AirGreen, a professional installation includes, among other things:

• proper piping preparation;
• the leak test;
• evacuation;
• the charge corresponding to the actual length;
• the inspection after commissioning.

3/8 in – 3/4 in piping

The brochure confirms a liquid line of 3/8 po and a gas line of 3/4 po.

It also indicates:

• maximum piping length: 246 feet / 75 m;
• maximum height difference: 98.4 feet / 30 m;
• flare fittings.

These limits offer good installation flexibility, but we always seek to avoid unnecessary lengths. A simple, accessible, and well-planned installation remains preferable to a complex route simply because the manufacturer allows a long maximum length.

MCA 39 A and MOP 40 A outdoors

The brochure specifies for the outdoor unit:

• MCA: 39 A
• MOP: 40 A

and for the indoor unit:

• MCA: 7 A
• MOP: 15 A

The AirGreen specification sheet lists an outdoor MCA of 39 A and an MOP of 40 A.

This information must be incorporated into the home's electrical analysis.

A large property may already have:

• electric heating;
• water heater;
• dryer;
• stove;
• charging station;
• spa;
• other significant loads.

We therefore never treat electricity as a mere formality added after choosing the equipment.

Consumption that varies with modulation

In cooling mode, the brochure shows power consumption of approximately 900 to 6,800 W, with a nominal value of 5,500 W.

In heating mode, it also indicates a range of approximately 900 to 6,800 W, with 5,050 W as the reference value.

These ranges directly show the effect of inverter technology.

Electricity consumption does not remain constant. It varies according to the load, outdoor temperature, and operating conditions.

Not ENERGY STAR and not Cold Climate: this is not a minor detail

The AirGreen product page classifies this combination as:

• ENERGY STAR: no
• Cold Climate: no

This point should be clearly stated when comparing it with other central heat pumps.

A system can perform well without being ENERGY STAR or cold-climate certified under the criteria of a given program.

This distinction can influence:

• rebates;
• eligibility for certain programs;
• comparison with -25 °C or -30 °C models;
• the net cost of the project.

The brochure provides no information allowing us to confirm ENERGY STAR certification for this combination. It mainly indicates its performance and operating range.

Warranty: verify the exact coverage sold by AirGreen

The AirGreen product page indicates a manufacturer’s warranty of:

10-year compressor – 10-year parts – 0-year labor, with the possibility of an additional warranty.

The attached brochure does not clearly provide a warranty table in the technical pages supplied.

We therefore recommend considering the warranty terms displayed on the AirGreen product page as the commercial reference for the product being sold, while confirming the registration requirements and applicable terms at the time of ordering.

When this 5-ton SENVILLE becomes a logical choice

We would look particularly closely at this model for:

• a large home equipped with existing ductwork;
• a home requiring high airflow;
• a replacement for a high-capacity central system;
• a light commercial space;
• an installation where the Top Discharge design makes outdoor placement easier;
• a homeowner who wants inverter technology but does not need cold-climate certification down to -30 °C.

We would be more cautious if the owner’s primary goal is a heat pump capable of meeting a large portion of the heating load at the coldest temperatures of a Quebec winter.

In this case, the capacities at -15 °C and -20 °C should be compared with those of other cold-climate models.

The biggest mistake to avoid with a five-ton heat pump

The main mistake would be to assume that “bigger” automatically means “better.”

A five-ton system installed in a house that actually needs only three or four tons can create several problems:

• improper cycling;
• excessive airflow;
• noise at the grilles;
• less effective dehumidification under certain conditions;
• unnecessary consumption;
• uneven comfort.

Conversely, a large house with an actual load close to five tons should not be equipped with a smaller system simply to reduce the initial price.

The right choice comes from consistent sizing.

What we review at AirGreen before confirming the SENTC-60TD

For a central heat pump installation in Montreal, Laval, Longueuil, on the South Shore, or on the North Shore, we analyze the entire system:

1. the required heating and cooling capacity;
2. the airflow the ducts can actually support;
3. the return-air size;
4. the condition of the plenum;
5. the electrical panel capacity;
6. the outdoor unit location;
7. the piping length;
8. the auxiliary heating strategy;
9. the thermostat and controls;
10. future access for maintenance.

This approach is what turns a good specification sheet into a truly comfortable installation.

Our assessment of the SENVILLE R32 Top Discharge 5-ton system

This SENVILLE has several noteworthy features for a high-capacity central system project:

• 5-ton / 60,000 BTU category;
• rated cooling capacity of 55,000 BTU/h according to the brochure;
• rated heating capacity of 57,000 BTU/h;
• Twin-Rotary DC Inverter technology;
• R-32;
• airflow of up to 1,740 CFM;
• heating operation down to approximately -20°C;
• 3/8 in – 3/4 in piping;
• Top Discharge outdoor unit;
• announced outdoor sound level of 60 dB(A);
• WiFi available as an option according to the AirGreen specification sheet.

It is particularly suitable when the building already has a properly sized duct network and the capacity requirement is genuinely high.

The most important point, however, remains validating the data for the exact combination. The figures in the AirGreen specification sheet and those in the brochure do not match perfectly for certain performance ratings and capacities at low temperatures. We therefore prefer to verify AHRI number 218338226 before basing a final decision on a single value.

Are you considering the SENVILLE R32 Top Discharge 5-ton system to replace your old central system? Contact AirGreen for a quote and a complete assessment of your ductwork, electrical supply, and heating needs. We serve Montreal, Laval, Longueuil, the North Shore, the South Shore, and Montérégie for the installation, maintenance, and servicing of central HVAC systems.