Central heat pump repair in Pont-Viau
| Service | Repair | Unit | Central heat pump |
|---|---|---|---|
| Area | Laval-des-Rapides (Laval) | Published | November 19, 2026 |
| Reading | 9 min | ||
Attachment 1 · job photo
A rooftop heating failure that required much more than a simple restart
In Pont-Viau, in a Laval area where several residential and institutional buildings have rooftop HVAC equipment, our AirGreen team was called for a performance issue on a central heat pump. The customer reported increasing discomfort: the system would start, the fan would run, but the air blown quickly became lukewarm, sometimes almost cold, and the auxiliary heat seemed to take over far too often.
Upon arrival, the technical context was clear: the outdoor unit was on a flat roof, exposed to wind, snow accumulation, freeze-thaw cycles, and rapid temperature changes typical of the greater Montreal area. This type of installation requires a more thorough inspection than a ground unit, as an apparent heating failure can stem from a weakened electrical component, a defrosting problem, lack of airflow, a faulty sensor reading, or a refrigerant imbalance.
The central heat pump inspected was an outdoor condenser connected to a ducted indoor system, with an estimated capacity of around 3 tons, or about 36,000 BTU. Since the technical label was partially exposed to the elements, we first verified the essential information directly on the unit: power supply, refrigerant type, operating range, rated current, control circuit condition, and configuration with the indoor thermostat.
Symptoms reported by the customer
The customer had noticed several signs which, taken separately, might have seemed minor, but together painted a very revealing picture:
- The central heat pump started normally, then lost efficiency after a few minutes.
- The thermostat was calling for heat, but the indoor temperature was rising slowly.
- The outdoor unit sometimes seemed to stop before the end of the cycle.
- The auxiliary heating was running more often than usual.
- A slight ice formation was visible near certain areas of the unit.
- The energy bill had increased without any major changes in the client’s habits.
At AirGreen, we know that a central system that “still works” can still be partially broken. This is precisely the kind of situation where a thorough HVAC diagnosis prevents unnecessary replacement of costly parts or, worse, concluding too quickly that the unit must be replaced.
Roof inspection and installation conditions
Even before opening the service panel, we inspected the environment around the unit. On a flat roof, the performance of a central heat pump depends greatly on the airflow around the condenser. Snow accumulation, insufficient clearance, leaves, displaced gravel, or an obstacle near the fan can impair heat transfer.
In this specific case, the unit was installed on a stable base, but some areas around the unit showed signs of compacted snow and frozen moisture. It was not enough to completely block the unit, but enough to complicate defrosting on cold days. We also checked the clearance around the top fan, the condition of the side grilles, the stability of the support, the wiring passage, and the condition of the nearby electrical disconnect.
This step is essential for interventions in Laval, on the North Shore, in Longueuil, on the South Shore, or in the denser neighborhoods of Montreal, where several units are sometimes grouped on rooftops. A central unit can be perfectly sized but lose a lot of efficiency if its immediate environment prevents it from breathing properly.
Electrical diagnosis: the weak point of the intervention
After the visual inspection, our technician conducted a complete electrical analysis. The measurements showed that the compressor was receiving the operation signal, but some components did not always respond consistently.
The first problematic element was the run capacitor. Its measured value was below its normal tolerance. A weakened capacitor can allow the motor to start but with reduced efficiency, increased electrical current, and additional stress on the compressor or outdoor fan. In a winter context, this weakness becomes even more apparent, as the central heat pump has to work harder to extract heat from the outside air.
The contactor also showed signs of wear. The contact points were blackened and slightly pitted, causing a less clean power supply to the compressor. This type of defect can create intermittent shutdowns, irregular cycles, and a “phantom” failure impression, especially when the unit runs every other time.
We also found a slightly loose low voltage wire in the control circuit. This detail could explain why some defrost cycles did not always complete properly. An unstable connection can prevent a control board, sensor, or reversing valve from receiving a constant signal, even if the unit appears mechanically sound.
Defrost and refrigeration circuit check
A central heat pump in heating mode must regularly manage moisture that turns into frost on the outdoor coil. The defrost cycle is therefore a crucial element. When this cycle is too short, too infrequent, or incomplete, the unit quickly loses its ability to heat.
We forced a defrost test according to the appropriate sequence and checked the unit's behavior: mode change, fan response, coil temperature, return to heating mode, thermostat response, and auxiliary heating operation. The defrost cycle would start, but the sequence was unstable until the low voltage issue was fixed and the weakened electrical components were replaced.
Next, we took pressure, temperature, superheat, and subcooling readings to confirm the condition of the refrigeration circuit. This step is important: adding refrigerant without a complete diagnosis is one of the most common mistakes in the HVAC field. An incorrect charge can worsen the problem, damage the compressor, or mask an electrical failure.
In this case, the readings indicated unbalanced operation mainly related to irregular cycles and electrical weakness, rather than a major leak. After stabilizing the operation, the values returned to a range consistent with outdoor conditions.
Repairs performed on site
Our intervention was structured in several steps to secure the device, stabilize its operation, and confirm the result under real conditions.
We replaced the run capacitor with a part that met the unit’s specifications. We then replaced the worn contactor, tightened electrical connections, secured low-voltage wiring, and checked the outdoor disconnect switch. Special attention was given to wiring exposed to vibrations and temperature variations, as rooftop installations often face more stress than wall or ground installations.
We also cleaned the accessible areas of the outdoor coil, removed accumulations that could hinder air circulation, and cleared the space around the base of the unit. The goal was not only to restart the central heat pump but to enable it to maintain its performance after we left.
Once the components were replaced, we restarted the system in heating mode. The compressor started steadily, the outdoor fan operated normally, and the thermostat was able to complete a demand without premature interruption. We observed several cycles to confirm that the device did not revert to its intermittent behavior.
Result: stabilized heating and more predictable operation
After the repair, the difference was clear. The air blown into the ducts was more consistent, the thermostat demand was met more quickly, and the auxiliary heating no longer engaged excessively. The client especially appreciated that we identified the real cause of the problem without immediately recommending a full system replacement.
An effective HVAC repair is not just about replacing a part. It must confirm why the part failed, how the device responds after correction, and what actions will prevent a recurrence. In this case, electrical wear, roofing conditions, and irregular defrosting combined to explain the loss of performance.
We explained to the client the signs to watch for in the following weeks: cycles that are too short, quick return of auxiliary heating, excessive ice formation, unusual noises, or significant temperature variation at the registers. We also recommended preventive maintenance before the coldest periods and before the air conditioning season, since a central heat pump works almost all year round.
What this repair at Pont-Viau shows about central systems
A central heat pump can be faulty even if it starts
Many customers wait until the unit completely stops working before calling a specialist. Yet, the most costly failures often start with subtle symptoms: short cycles, reduced efficiency, more frequent auxiliary heating, different noises, abnormal frost, or unstable temperature.
In this case at Pont-Viau, the unit was not “dead.” It started, ventilated, and still produced some heat. But its operation was unstable, which increased energy consumption and put unnecessary stress on the compressor.
This is exactly why AirGreen takes a comprehensive approach to heating, air conditioning, and ventilation systems. Whether the call comes from Montreal, Laval, Longueuil, the North Shore, or the South Shore, our priority is to understand the failure before proposing a solution.
Mistakes to avoid before calling for service
Some actions may seem convenient but risk worsening a failure on a central heat pump:
Resetting the circuit breaker multiple times
If a circuit breaker trips or a system stops repeatedly, restarting it without diagnosis can further damage components. A worn contactor, a weak capacitor, or an overloaded motor should be checked promptly.
Assuming the thermostat is always responsible
The thermostat may be the cause, but it is not always the main problem. In this case, the heating request was properly sent, but the response from the outdoor unit was unstable due to weakened electrical components.
Adding refrigerant without complete measurements
Refrigerant charge cannot be guessed. It must be verified with precise readings and according to operating conditions. An unnecessary recharge can reduce the unit’s lifespan.
Letting snow accumulate around the unit
Even on a roof, snow can create obstacles around the base, interfere with defrosting, or promote ice moisture buildup. Proper clearance remains essential.
Why choose AirGreen for HVAC repair
Our team works daily on central heat pumps, wall systems, multi-zone units, electric furnaces, air exchangers, and complex HVAC solutions. This diversity allows us to make a more accurate diagnosis, especially when multiple factors overlap.
In Pont-Viau, the success of the intervention relied on the ability to connect the customer’s symptoms to the measurements taken on the roof: weak capacitor, worn contactor, unstable low voltage signal, irregular defrosting, and airflow to optimize. None of these elements alone told the whole story. Together, they perfectly explained the breakdown.
We serve residential and commercial customers throughout the greater Montreal area, including Laval, Longueuil, the North Shore, and the South Shore, with an approach focused on precision, transparency, and repair durability.
An intervention that extends the system’s useful life
Replacing a central heat pump is a significant investment. When a well-targeted repair can stabilize the unit and restore performance, it becomes a smart solution for the customer. In this case, replacing weakened electrical components and verifying defrosting helped prevent more serious compressor damage.
The customer regained more reliable heating, better peace of mind, and a clear understanding of the condition of their system. This is exactly what we aim for with every service call: a concrete, measurable, and long-term useful result.



