AirGreen job in

Repair of a Wall-Mounted Heat Pump in Dollard-des-Ormeaux

Wall-mounted heat pump9 min

Stylised map, not to scale.

Area served
  • Montréal
  • Laval
  • Longueuil
  • South Shore
  • North Shore

An aging wall heat pump that cooled poorly and left marks on the ceiling

In Dollard-des-Ormeaux, in the residential area of West Island, our AirGreen team was called for a common problem on older wall units: a wall heat pump installed near the ceiling that was still working but whose performance had clearly decreased. The client noticed less effective air conditioning, irregular airflow, a slight smell at startup, and dark marks above the indoor unit.

The unit visible on site was a compact wall unit, an older generation, installed in a bright living area near a large window. The yellowed facade over time, the proximity to the ceiling, and the dark marks on the wall already gave us several important clues. This type of wall heat pump can continue to start for years but gradually lose its ability to distribute air well if the evaporator, turbine, filters, and drainage system are not properly maintained.

The client was not facing a complete breakdown. The situation was more subtle: the unit was blowing air, but not enough; it was cooling, but not quickly; it was working, but with a feeling of mechanical fatigue. It is precisely in such cases that a full HVAC diagnosis is essential, because replacing the unit too quickly is not always necessary, while a simple superficial cleaning does not always fix the real cause.

Symptoms reported before our arrival

During the call, the client described several signs that had gradually worsened:

  • The blown air seemed less cold than before.
  • The airflow was weak, even at high speed.
  • A damp smell appeared at startup.
  • The room took much longer to cool down.
  • Small dark marks were visible above the unit.
  • The air outlet flap seemed to direct the air less effectively.
  • The unit sometimes produced a slight vibration or rubbing noise.

These symptoms pointed to several possibilities: saturated filters, clogged turbine, partially blocked internal coil, dirty condensate tray, slow drain, worn-out ventilation motor, miscalibrated thermistor, or installation too close to the ceiling limiting air intake.

On a wall-mounted heat pump installed so close to the ceiling, even slight dirt buildup becomes more noticeable. The return air flows less freely, dust accumulates faster around the casing, and marks on the wall can appear when particle-laden air is drawn in or expelled irregularly.

Visual inspection of the indoor unit

Upon our arrival in Dollard-des-Ormeaux, we began by inspecting the indoor unit. The unit was mounted high on the wall, with limited space between the top of the unit and the ceiling. This installation is not uncommon in houses, condos, and multiplexes in Montreal, Laval, Longueuil, the North Shore, and the South Shore, especially when the unit was installed several years ago.

What the unit’s position revealed to us

A wall unit must draw air from the top or front, depending on the model. When the upper space is too limited, the unit can operate, but its airflow becomes less optimal. In the short term, the customer may not necessarily notice a problem. In the long term, the filters clog faster, dust accumulates in the heat exchanger, the fan gets dirty, and the system works harder to produce the same comfort.

In this case, the proximity to the ceiling partly explained the dark marks visible around the unit. These marks do not always come from a leak or electrical problem. They are often caused by dust-laden airflow combined with humidity and internal dirt buildup.

Condition of the filters and the panel

After opening the panel, we found that the filters were dirty. They were not completely blocked, but sufficiently loaded to reduce airflow. On a wall unit, the filters are the first barrier against dust, pet hair, pollen, and household particles. When not cleaned regularly, the rest of the unit gets dirty much faster.

The interior panel also showed fine deposits, especially near the air outlet areas. This confirmed that the unit needed deeper maintenance than just an external dusting.

HVAC diagnosis: finding the cause of performance loss

Our diagnosis was not limited to observing the filters. We analyzed the complete behavior of the wall-mounted heat pump in operation.

Airflow verification

We first tested the different fan speeds. The motor responded to commands, but the actual airflow remained below what is expected from a well-functioning wall unit. This indicated that the problem was not just a control or setting issue, but probably an internal blockage.

Ventilation turbine inspection

The turbine, also called the blower wheel, was heavily soiled. On wall units, this part is often neglected because it is less visible than the filters. Yet, it plays a major role in comfort. When its fins are covered with dust and residue, it moves less air, becomes noisier, and can cause vibration.

In this case, the turbine’s dirtiness directly explained the low airflow and intermittent noise. The unit was producing cold air, but the air was no longer circulating properly in the room.

Indoor coil inspection

We then inspected the evaporator coil. It showed an accumulation of dust and residue on the fins. This type of blockage reduces heat exchange: air passes less effectively through the coil, temperature becomes less stable, and humidity can accumulate in the drainage pan.

A dirty coil can also mimic a refrigerant shortage because the blown air becomes less effective. This is a common mistake. Before concluding a leak or compressor problem, it is always necessary to confirm that the indoor heat exchanger and airflow are in good condition.

Condensate drainage check

Since the customer mentioned a musty smell, we checked the condensate pan and the drainage line. The drain was not completely clogged, but it was slowed down by deposits. This situation can cause water to stagnate in the pan, which promotes odors and increases the risk of overflow.

In an HVAC repair, a partially blocked drain is as important as a weak electrical component. A wall-mounted heat pump can cool properly, but if the condensation water does not drain well, the customer risks odors, drips, wall stains, and sometimes damage to the interior finish.

Intervention performed by AirGreen

After the diagnosis, we carried out a complete intervention on the indoor unit.

Thorough cleaning of filters and front panel

The filters were removed, cleaned, and inspected. The front panel was carefully cleaned, especially around the blowing areas. This step improves the appearance of the unit, but mainly helps reduce the amount of dust that returns to the room.

Blower turbine cleaning

We performed a thorough cleaning of the fan. This operation requires time and precision, as the blades are numerous and deposits can be stuck by moisture. A poorly cleaned fan often continues to vibrate or blow unevenly.

After cleaning, the airflow was noticeably better. The rubbing noise decreased, and the air was distributed more evenly throughout the room.

Cleaning the indoor coil

The evaporator coil was cleaned to restore heat exchange. We paid special attention to protecting the wall, furniture, and decorative elements located under the unit. In an occupied room, professional cleaning must be clean, controlled, and safe.

Cleaning the coil improved cooling capacity and reduced the system’s load. A unit that breathes better works less to reach the desired temperature.

Partial drain unclogging and rinsing

We then cleaned the condensate pan and rinsed the drain line. The flow became smoother again, reducing the risk of odors and water leaks. We also checked the slope and drainage behavior during operation.

No major parts needed to be replaced. The intervention mainly involved fixing the causes of dirt buildup and slowed drainage before they caused a more serious breakdown.

Final operational tests

After the intervention, we restarted the unit and tested several ventilation modes. The airflow was stronger, the blowing temperature more stable, and the noise much less noticeable. The client also noticed the room started cooling down faster.

What this repair in Dollard-des-Ormeaux shows about wall heat pumps

This intervention highlights a key point: a wall heat pump can lose much of its efficiency without actually being “broken.” In many cases, the problem comes from gradual internal dirt buildup, a slowed drain, or an installation that slightly limits air circulation.

Mistakes to avoid with an old wall unit

Cleaning only the filters

Filters are important, but they are only part of the maintenance. The fan, coil, condensate pan, and drain must also be inspected. A unit can have clean filters and still be ineffective if the fan is covered in dust.

Ignoring marks on the wall or ceiling

Dark marks around a wall unit are not just aesthetic. They can indicate poor air circulation, internal dirt buildup, or excessive moisture. The sooner the problem is addressed, the easier it is to avoid odors, vibrations, and leak risks.

Automatically thinking about replacement

An older wall unit deserves a full evaluation before concluding it needs replacement. In this case in Dollard-des-Ormeaux, the system still had useful functional capacity. A targeted intervention restored comfort without immediate replacement.

Waiting until there is water on the floor

A partially blocked drain often shows warning signs: musty odor, water noise, unusual condensation, wall stains, or performance drop. Waiting for a visible leak can cause unnecessary damage.

Recommendations given to the client

At the end of the service call, we recommended periodic maintenance tailored to the actual use of the device. In a home where the heat pump is used both for cooling in summer and heating during cooler periods, the unit operates several months a year. Filters should be cleaned regularly, and more comprehensive maintenance should be scheduled before peak usage seasons.

We also explained that the location near the ceiling requires special attention. Even if the unit can remain in place, dust buildup and airflow need to be monitored more closely.

AirGreen, specialist in HVAC service calls in Greater Montreal

At AirGreen, we regularly service wall-mounted heat pumps, wall air conditioners, MultiZone systems, central heat pumps, electric furnaces, and other HVAC equipment in Montreal, Laval, Longueuil, on the North Shore and the South Shore. Every service call is handled with a clear method: inspection, diagnosis, correction, final testing, and practical recommendations.

This repair of a wall-mounted heat pump in Dollard-des-Ormeaux restored the device to cleaner, quieter, and more efficient operation. The client regained more stable comfort, without unnecessary replacement, along with a better understanding of the maintenance needed to extend the system's lifespan.

You made it to the end.Share it with someone it could help.
Near you

Other AirGreen jobs around Dollard-des-Ormeaux

Other jobs, not the one described above. Places we recognise also appear on the map.

Keep reading

Latest published jobs

AirGreen Climatisation & Chauffage

The same service at your place?

Cleaning, repair or maintenance: tell us about your unit and we schedule the visit.

  • RBQ licence 5645-9605-01Subclasses 15.8, 15.10 and 16
  • $5M liability insuranceOn every job
  • 15+ yearsFamily-owned, based in Montréal