Installation of a Sharp wall-mounted heat pump in Rosemont–La Petite-Patrie
Installation of a Sharp wall-mounted heat pump in Rosemont–La Petite-Patrie: comfort, performance and aesthetic integration guaranteed by AirGreen, HVAC experts in Montreal and the surrounding area.

Take a tour of the installation
Each number is a point we check on site. Switch between summer and winter to watch air and heat move.
In summer, the outdoor unit rejects the house's heat outside.
Generic illustration of this type of installation, not a survey of this job site. Tap a number.
Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.
The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.
Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.
A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.
The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.
On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.
The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.
A wall-mounted heat pump installation project adapted to a family living space
At AirGreen , we know that a wall-mounted heat pump installation is about more than just technical performance: it must integrate seamlessly into the living space, both aesthetically and functionally. In a bright apartment in Rosemont–La Petite-Patrie , our team recently installed a Sharp wall-mounted heat pump . The project stood out for a particular wall design challenge: a wall serving as a decorative blackboard, used by the family to leave messages and drawings.
This seemingly simple detail had a direct influence on the planning of the installation. We had to find the right balance between the machine's performance and respect for the daily use of this creative space.
Space analysis and technical planning
Even before installing the Sharp wall head , we took care to evaluate all the technical constraints:
-
Optimal height : the interior head had to be installed high enough to ensure even air diffusion, while respecting the surface of the wall board.
-
Ductwork positioning : the refrigerant pipe outlet has been planned discreetly to avoid any interference with the daily use of the cabinet and the board.
-
Electricity : A control box already present nearby facilitated the connection, thus reducing intervention time and the need for additional work.
This preparation allowed us to ensure an efficient, clean and durable installation.
The advantages of the installed Sharp heat pump
The Sharp wall-mounted heat pump chosen by customers perfectly meets the needs of an apartment of this type:
-
Suitable heating and air conditioning capacity : ideal for a medium-sized home.
-
Inverter technology : it continuously adjusts its power to maintain constant comfort while reducing electricity consumption.
-
Quiet : an essential criterion for a family, especially in a living space where calm is sought.
-
Simplified maintenance : Easily accessible filters allow occupants to maintain good indoor air quality with minimal effort.
Thanks to these features, the device perfectly meets the requirements of four-season comfort in an urban environment like Rosemont.
Installation process
Our technicians followed the following steps:
-
Protection and preparation : covering the furniture and the painting area to avoid any dust or dirt.
-
Drilling and installation of pipes : discreet passage through the wall, with white capping matching the interior paint.
-
Wall-mounted head : perfectly level installation, respecting the optimal height for efficient airflow.
-
Electrical and refrigerant connections : carried out in accordance with safety standards and manufacturer's recommendations.
-
Start-up and calibration : performance test in heating and air conditioning modes, verification of condensate drainage and adjustment of diffusion flaps.
The result is a harmonious, functional installation ready to offer comfort and energy savings from day one.
Benefits for the family
Beyond immediate comfort, this installation has several advantages:
-
Energy savings thanks to the high energy efficiency of the device.
-
Personalized comfort : the family can adjust the temperature precisely, summer and winter.
-
Enhancement of space : despite the presence of a decorative wall, the heat pump was integrated in an aesthetic manner, without harming the visual aspect or the use of the family table.
-
Grant eligibility : The device meets the performance criteria for obtaining financial assistance for Montreal residents.
AirGreen expertise at your service
This project demonstrates our expertise: at AirGreen, we don't just install a device. We're always thinking about the best way to combine technical performance, aesthetic constraints, and daily comfort . Each wall-mounted heat pump installation in Montreal, Laval, Longueuil, on the North Shore and the South Shore is an opportunity for us to demonstrate our commitment to quality and customer satisfaction.
The big day, step by step
The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.
We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
Model, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
Floors and furniture protected, wall plate position marked level, wall opening located.
A single opening, with the slope the drain needs to flow outside.
Set on a stand raised above the snow, with the clearances the manufacturer requires.
Connected, insulated and protected. The opening is then sealed against water, cold air and insects.
A dedicated circuit and an accessible disconnect near the outdoor unit.
Leak test, vacuum, then start-up and a check of heating and cooling.
Remote, modes, filters: we show you the essentials before we leave.
- The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
- The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
- Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
- The wall openingA single opening, with the slope the drain needs to flow outside.
- The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
- Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
- The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
- Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
- The walkthroughRemote, modes, filters: we show you the essentials before we leave.
What would it look like at your place?
Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.
Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.
Four mistakes we do not make
Flip each card to see what we do instead.
Your own project, step by step
What to do, season by season
Three habits per season for this unit. They take a few minutes and prevent many calls.
- Clean the indoor unit's filters.
- Clear leaves and debris left on the outdoor unit by winter.
- Test cooling before the first hot days.
- Clean the filters more often when the unit runs a lot.
- Keep plants away from the outdoor unit.
- Check that no water drips from the indoor unit.
- Rake the leaves around the outdoor unit.
- Test heating before the first cold days.
- Book periodic maintenance before winter.
- Keep snow away from the stand and the front of the unit.
- Let the unit defrost: it is normal.
- Never hit the ice on the fins; call us if the unit stays iced up.
Is your home ready?
Check what applies at your place. A "no" is not a refusal: it is what we sort out during the estimate.
Four statements: true or false?
It all comes down to details you have just seen.
1. In heating mode, the outdoor unit can produce water.
During defrost cycles. That water must drain away without forming ice.
2. You pick the capacity with a simple square-footage rule.
Windows, insulation, orientation and how the room is used all count. Capacity is chosen on site.
3. A multi-zone connects several indoor heads to a single condenser.
One head per room, all on the same condenser. Each room keeps its own temperature.
4. The disconnect can sit behind the patio furniture.
It must stay accessible: it is what shuts the unit off for service.
0 / 4 right answers
What people ask us about this kind of work
Does a wall-mounted heat pump heat in winter?
Wall-mounted or multi-zone: how do I choose?
Where does the outdoor unit go?
Are there grants?
Do I need a permit?
How cold can it heat?
How much can I save?
How is the LogisVert assistance calculated?
Is it noisy?
The outdoor unit is covered in ice: is that normal?
Does AirGreen hold the required licences?
Is the estimate free?
No question matches. Write to us: we answer.
More jobs to see, near you
By town, by equipment or by region: browse more than 4,700 published projects.
Each dot: a town where AirGreen has published projects. The glowing dot: this job.
Every house has its constraints. We see them before we install.
The on-site estimate is free and the quote follows within 24 hours.
Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).
