Project

Installation of a Sharp ZU1 wall-mounted heat pump in Rosemont–La Petite-Patrie

AirGreen installs a Sharp ZU1 in Rosemont: R-32 wall-mounted heat pump, discreet integration, four-season comfort and energy savings. HVAC service for Montreal, Laval, Longueuil, North Shore, South Shore.

By AirGreen Climatisation & Chauffage Admin6 min read
Installation of a Sharp ZU1 wall-mounted heat pump in Rosemont–La Petite-Patrie
Installation of a Sharp ZU1 wall-mounted heat pump in Rosemont–La Petite-Patrie
Generic diagram: wall-mounted heat pump, indoor and outdoor units

In summer, the outdoor unit rejects the house's heat outside.

Generic illustration of this type of installation, not a survey of this job site. Tap a number.

  1. Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.

  2. The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.

  3. Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.

  4. A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.

  5. The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.

  6. On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.

  7. The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.

Precise and quiet comfort in a Montreal plex: our installation of a Sharp ZU1 wall head in the heart of Rosemont

At AirGreen , we work weekly in plexes and condos in Montreal's inner city where space, aesthetics, and silence are paramount. This Sharp ZU1 wall-mounted heat pump installation in a Rosemont–La Petite-Patrie home illustrates how we adapt a modern HVAC solution to the typical architecture of Montreal interiors: crown moldings, load-bearing brick walls behind drywall, windows near room corners, and discreet passages to the exterior wall.

The context: a need for efficient supplemental heating and controlled cooling

The owner wanted:

  • Stabilize the temperature of the living room and an adjoining dining area, which is often too hot in summer and cooler in winter .

  • Reduce operating costs compared to existing electric convectors.

  • Preserve the visual discretion of a recently renovated space (cream walls, white moldings).

After calculating thermal loads and verifying the path constraints, we recommended a Sharp ZU1 (new generation R-32 ), chosen for its extreme cold operating range , its fine modulation and its low noise signature .

Technical choice: the Sharp ZU1 series for the Montreal climate

The ZU1 range is positioned as a safe bet for urban housing:

  • High-efficiency inverter ensuring continuous modulation and long cycles, synonymous with stable comfort.

  • R-32 refrigerant , with reduced GWP , improving heat exchange and heating capacity in cold weather.

  • Extreme cold performance down to approximately −25°C to −30°C depending on capacity , making it ideal for Montreal winters.

  • Advanced dehumidification functions and automatic shutter management for even diffusion .

  • Very low noise level from the interior head, appreciable in open living rooms.

Desired result: a wall-mounted heat pump that heats quickly, cools gently, without drafts and without temperature variations.

Integration into the room: precision of the installation

We positioned the head in the upper part , under the ceiling molding, on a central wall providing a clear draft towards the living room. This placement:

  • maximizes controlled stratification (warm air in winter, cool air in summer);

  • facilitates a gravity path of the condensate drain;

  • limits the visibility of the chute, here reduced to the essentials.

The wall-mounted remote control is mounted at an ergonomic height, near a power outlet, for quick access. The Sharp's discreet display and sleek front panel complement the apartment's light finishes .

Refrigeration path and condensate evacuation: clean and sustainable

The passage is made through the rear partition towards the exterior wall . We opted for:

  • a single drilling with waterproof sheath,

  • a continuous slope ensuring gravity drainage (no condensate pump required),

  • a white UV exterior capping , harmonized with the coating,

  • galvanized wall brackets for the condenser, raised from the ground to avoid snow and splashes.

The length of the refrigerant line + cable assembly remains contained (≈ 2.5 to 3.5 m in this configuration), which optimizes pressure losses and facilitates maintenance.

AirGreen Methodology: An HVAC Installation Without Compromise

We follow a rigorous protocol on each site:

  1. Nitrogen pressurization and extended leak test .

  2. Deep vacuum draw to the required level and controlled stability .

  3. Tightening torques respected on flared fittings and control of anti-condensation insulation .

  4. Electrical checks (conductor section, dedicated circuit breaker, differential if required).

  5. Start-up and calibration : supply temperatures, intensity, superheating/subcooling, adjustment of the flaps to direct the airflow along the ceiling and avoid discomfort in the seating area.

  6. Quick occupant training : modes, seasonal instructions, basic maintenance.

Real comfort and measurable benefits

From the first hours of use, the customer notices:

  • rapid and even cooling of the living room in wall-mounted air conditioner mode, without parasitic noise;

  • in heating, a gentle rise which eliminates the feeling of cold on the floor;

  • controlled electricity consumption thanks to continuous modulation and optimized settings (21–22°C winter, 23–24°C summer).

In addition, the Sharp ZU1 improves perceived air quality thanks to regular mixing and basic filtering , particularly useful during urban heat waves.

HVAC maintenance: simple steps to maintain performance

To maintain yields and sustainability:

  • Clean filters every 4 to 6 weeks during periods of heavy use.

  • Keep the outdoor condenser clear (leaves, dust, snow).

  • Schedule an annual maintenance : check pressures, blowing temperature, condition of insulation and tightening, electrical inspection.

These actions extend the life of the equipment and preserve the expected savings .

Grants and local compliance

Depending on the configuration and capacity chosen, a recent Sharp R-32 wall-mounted heat pump may be eligible for provincial grant/energy efficiency programs when it meets Energy Star thresholds and cold weather heating criteria. We support our clients in Montreal, Laval, Longueuil, North Shore and South Shore to verify eligibility , prepare documentation and optimize the investment .

Why AirGreen for your project in Rosemont–La Petite-Patrie?

  • Mastery of the constraints of Montreal plexes: load-bearing walls, exterior access, restricted spaces, interior aesthetics.

  • Teams certified and trained on the latest R-32 generations .

  • Complete support : sizing, brand selection, turnkey HVAC installation , maintenance.

  • Responsive after-sales service , parts and adjustments available quickly in Greater Montreal.

Practical advice before your installation

  1. Capacity selection (BTU) : base it on a load calculation , not just the surface area. High ceilings, sunlight and the envelope influence the sizing.

  2. Head location : Aim at a central wall without obstacles, to avoid dead zones and limit perceived noise.

  3. Condensate management : favor a gravity slope ; a pump is only considered as a last resort.

  4. Winter : Maintain clearance around the condenser to prevent ice buildup and facilitate defrosting.

  5. Smart instructions : avoid extreme temperature swings; let the inverter work.

Project review

This Sharp ZU1 wall-mounted heat pump installation in Rosemont–La Petite-Patrie proves that a compact solution can deliver exemplary four-season comfort in a Montreal home, with minimal visual impact and tangible energy savings . By focusing on a discreet path, careful adjustment, and a sleek yet quiet interior head, we deliver a seamless user experience every day.

AirGreen supports owners and managers in Greater Montreal with sustainable HVAC projects: equipment selection, installation , HVAC maintenance , and optimization advice. Your comfort deserves impeccable execution.

In figures
The steps

How it goes, from the first call to the end

The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.

Step 1 of 9The on-site estimate

We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.

  1. The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
  2. The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
  3. Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
  4. The wall openingA single opening, with the slope the drain needs to flow outside.
  5. The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
  6. Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
  7. The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
  8. Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
  9. The walkthroughRemote, modes, filters: we show you the essentials before we leave.
The unit

What the unit delivers when it is cold

The range as published on airgreen.ca: pick a size to see its capacity in deep cold.

The range, size by size
SizeHeating at −8 °CHeating at −15 °CColdest certified pointCOP at −15 °CSEERHSPFIndicative LogisVert aid
Sharp ZU1 12 00014,50012,000−27 °C: 7,2002.1122.011.0$1,740
Sharp ZU1 15 00018,10015,300−27 °C: 10,1002.124.011.0$2,172
Sharp ZU1 18 00022,00018,000−27 °C: 11,5002.224.011.0$2,640
Sharp ZU1 24 00022,40019,000−27 °C: 12,3002.222.011.0$2,688
14,500Its full nominal heating at −8 °C

According to NEEP, it delivers 14,500 BTU/h at −8 °C (17 °F), more than at 8 °C (14,000 BTU/h). It heats as hard in moderate cold as in mild weather.

7,200Still 7,200 BTU/h at −27 °C

According to NEEP, its certified maximum capacity at −27 °C (−17 °F) is 7,200 BTU/h, 60% of its nominal 12,000 BTU size.

17,100A 17,100 BTU/h reserve in mild weather

At 8 °C, its certified maximum capacity reaches 17,100 BTU/h, 42% more than its nominal 12,000 BTU size.

Data read live from the airgreen.ca page of each size (NEEP / AHRI certified performance). When the title names the installed size, it is highlighted; otherwise the whole range is shown. The aid shown is today’s, using Hydro-Québec’s rule ($120 per 1,000 BTU/h at −8 °C); amounts quoted in the article date from its publication. Only Hydro-Québec confirms the assistance granted.

Your numbers

And at your place?

Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.

Before / afterThe cost of the same heat

Baseboards and electric furnaces turn 1 kWh of electricity into 1 kWh of heat. A heat pump delivers more: that is its COP. At Hydro-Québec’s rate D (11.142¢/kWh above 40 kWh a day, since 1 April 2026):

Before · baseboards11.142¢/kWh
After · heat pump–

Hydro-Québec: a heat pump can be up to three times more efficient than baseboards for heating in the colder months.

Estimate per kWh of heat, at the chosen temperature, using the certified COP from the product page. Taxes, access charge and backup heat not included.

Size checkYour baseboards, in BTU/h
–BTU/h of installed electric heat

    Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.

    Through the seasons

    What to do, season by season

    Three habits per season for this unit. They take a few minutes and prevent many calls.

    • Clean the indoor unit's filters.
    • Clear leaves and debris left on the outdoor unit by winter.
    • Test cooling before the first hot days.
    And at your place?

    Which type of equipment for your project?

    Pick what looks like your need.

    Mistakes avoided

    Four mistakes we do not make

    Flip each card to see what we do instead.

    Frequently asked questions

    What people ask us about this kind of work

    12 questions
    Does a wall-mounted heat pump heat in winter?
    Yes, it heats and cools. Its capacity drops in very cold weather; the operating range depends on the model and is listed on its spec sheet.
    Wall-mounted or multi-zone: how do I choose?
    One wall head and one condenser outside: the direct solution for a room or an open area. For two to five rooms, a multi-zone puts one head in each room on a single condenser.
    Where does the outdoor unit go?
    Where it stays above the snow, clear and accessible, away from walkways. We decide it with you during the estimate.
    Are there grants?
    Depending on the model and your situation, assistance programs may apply, including Hydro-Québec's LogisVert. AirGreen checks the model number before quoting an amount. See the grants.
    Do I need a permit?
    Rules vary from city to city: location, distances, noise. See permits and by-laws, and we check for your address.
    How cold can it heat?
    It depends on the model. According to Hydro-Québec, newer models work down to a temperature between −15 °C and −25 °C, and some cold-climate models are certified lower. The minimum temperature is on each unit's spec sheet.
    How much can I save?
    Hydro-Québec says a heat pump can be up to three times more efficient than baseboards for heating in the colder months. The result depends on the house, the climate and how it is used.
    How is the LogisVert assistance calculated?
    For ENERGY STAR cold-climate certified heat pumps, Hydro-Québec lists assistance of $120 per 1,000 BTU/h of heating capacity at −8 °C. AirGreen checks the exact model before quoting an amount; only Hydro-Québec confirms the assistance granted. See the grants.
    Is it noisy?
    The sound level depends on the model and is listed in decibels on each unit's spec sheet. Location matters too: when possible, we avoid putting the outdoor unit under a bedroom window.
    The outdoor unit is covered in ice: is that normal?
    Some frost is: the unit runs defrost cycles. Never hit the ice. If the unit stays iced up or stops heating, call us.
    Does AirGreen hold the required licences?
    Yes. AirGreen holds RBQ licence 5645-9605-01, subclasses 15.8 Ventilation, 15.10 Refrigeration and 16 Electricity.
    Is the estimate free?
    Yes. The on-site estimate is free and the quote follows within 24 hours. Book my free estimate.
    Going further

    Useful pages for what comes next

    Could this job help a neighbour?

    Share
    Similar projects

    More jobs to see, near you

    By town, by equipment or by region: browse more than 4,700 published projects.

    Each dot: a town where AirGreen has published projects. The glowing dot: this job.

    All our projects

    Your project

    Tell us about your house. We come and see it for free.

    The on-site estimate is free and the quote follows within 24 hours.

    • RBQ licence5645-9605-01 · 15.8, 15.10, 16
    • EstimateOn site, free
    • QuoteWithin 24 hours

    Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).

    Leave a comment