Installation of a MIDEA EVOX G3 2-ton central heat pump in Lorraine on the North Shore
AirGreen installs a 2-ton MIDEA EVOX G3 central heat pump in Lorraine: clean wall integration, HVAC performance, central comfort, and local expertise on the North Shore.

In summer, the outdoor unit rejects the house's heat outside.
Generic illustration of this type of installation, not a survey of this job site. Tap a number.
It captures or rejects heat outside. It sits on a level base, above the snow, with free space all around.
The insulated refrigerant lines enter the house through a sealed opening and run to the indoor coil.
A shut-off switch near the outdoor unit isolates it safely for service.
Sitting on the indoor module, it moves heat between the house air and the refrigerant.
Electric furnace or air handler: its fan pushes air through the ducts. The electric backup takes over in extreme cold.
Supply ducts bring air to the rooms; returns bring it back to the unit. Their condition matters as much as the unit's.
It protects the coil and the fan. A dirty filter cuts airflow, so it gets checked regularly.
It runs the heat pump and the backup heat. It must be compatible with the installed system.
A compact, clean, and well-suited central installation for a home in Lorraine
In Lorraine, on the North Shore, our AirGreen team recently installed a MIDEA EVOX G3 2-ton central heat pump, a particularly relevant HVAC solution for homeowners who wish to improve their comfort without multiplying wall-mounted units in living areas.
Upon arrival at the site, one element caught our attention: the available outdoor space was limited, with horizontal siding, an exposed foundation, a nearby shrub, and clearance around the outdoor unit that needed optimization. This type of configuration is common in residential areas of Lorraine, Rosemère, Bois-des-Filion, and Sainte-Thérèse, where homes are well-maintained, but the aesthetic and practical integration of a central heat pump requires real precision.
The MIDEA EVOX G3 outdoor unit was installed on robust, well-leveled wall brackets, with sufficient clearance to ensure good airflow. This approach helps protect the unit from snow accumulation, ground moisture, and seasonal ground movements, which is essential in the climate of the Greater Montreal, Laval, Longueuil, North Shore, and South Shore regions.
Why a 2-ton central heat pump was a logical choice
In this project, the choice of a 2-ton capacity met a specific need: to provide efficient heating and cooling through the existing ductwork, without oversizing the equipment. A common mistake in HVAC installation is to believe that a larger unit will automatically be more efficient. In reality, an oversized heat pump can lead to short cycles, less effective dehumidification in summer, more wear and tear, and less stable comfort.
The MIDEA EVOX G3 is often chosen for its interesting combination of efficiency, quiet operation, and winter performance. For a house well-suited to a 24,000 BTU capacity, it can replace or supplement an existing heating system while providing uniform central air conditioning.
Careful outdoor integration: the detail that changes everything
The image of this installation shows clean, discreet, and thoughtful work. The unit is positioned on a clear section of the wall, high enough to avoid snow-related problems and low enough to allow reasonable service access. The wall mounts are aligned, solid, and fixed to ensure the stability of the unit.
We also paid attention to the proximity of the shrub located to the left of the unit. Vegetation too close to a heat pump can hinder airflow, retain moisture, and complicate seasonal maintenance. In this case, the available space allows for a functional installation, but we always recommend that homeowners maintain a clear area around the unit.
Important technical points observed in this installation
- MIDEA EVOX G3 outdoor unit installed on wall brackets.
- Capacity: 2 tons, or approximately 24,000 BTU.
- Installation on foundation, with ground clearance.
- Careful positioning to preserve access to the service panel.
- Discreet location, close to the wall, without compromising ventilation.
- Clean exterior integration, without visual clutter.
What this installation reveals about a good HVAC approach
A central heat pump is not just a machine that is placed outside. It is a complete system that must work with the ductwork, the indoor unit, the actual needs of the house, electrical constraints, available space, and the habits of the occupants.
In Lorraine, as in several municipalities on the North Shore, homeowners often seek a durable, discreet, and efficient solution. The MIDEA EVOX G3 fits this profile well, especially when installed rigorously.
The importance of outdoor positioning
The positioning of the outdoor unit directly influences the performance and lifespan of the system. An installation too close to the ground can expose the machine to snow, ice, and debris. An installation too close to an obstacle can hinder heat exchange. A poorly leveled installation can cause vibrations, noise, and premature wear.
In this project, wall mounting helps reduce several risks:
- snow accumulation around the base;
- excessive exposure to runoff water;
- displacement due to freezing and thawing;
- obstruction by leaves, dirt, or small debris;
- difficulty of access during future HVAC maintenance.
A central unit designed for year-round comfort
The MIDEA EVOX G3 central heat pump is designed to provide heating in winter and cooling in summer. In a ducted home, it distributes treated air more uniformly than a single wall-mounted unit. This is a major advantage for families who want stable comfort in several rooms without having multiple visible wall-mounted units.
For homeowners in Lorraine, Laval, Montreal, Longueuil, the North Shore, or the South Shore, this type of system is particularly interesting when the building already has central infrastructure. The transition to a central heat pump then becomes more natural, especially if the goal is to reduce reliance on a more expensive heating source.
Mistakes to avoid before installing a central heat pump
An installation like this requires a complete evaluation. Before recommending a MIDEA EVOX G3 2-ton, we must validate several elements. Among the common mistakes we see in the field:
Choosing capacity solely based on area
The area gives an indication, but it is not enough. Insulation, house orientation, number of floors, duct condition, windows, and usage habits strongly influence the choice of capacity.
Neglecting the condition of the ductwork
A high-performance central heat pump cannot compensate for unbalanced, overly restrictive, or poorly insulated ductwork. Before installation, we check whether the air distribution system can support the expected performance.
Installing the outdoor unit too close to an obstruction
Hedges, fences, side walls, balconies, and stairs can reduce airflow. In this installation in Lorraine, the proximity of vegetation was taken into account to ensure proper operation.
Forgetting service access
A machine must be installed to operate, but also to be maintained. Technicians must be able to access panels, connections, and main components without unnecessarily disassembling the environment around the unit.
A finish that reflects AirGreen's field experience
At AirGreen, we place great importance on visible and invisible details. The client sees the outdoor unit, brackets, positioning, and cleanliness of the installation. But behind this result, there are also calculations, verifications, preparation, and adjustments that allow the system to function correctly after we leave.
In this project in Lorraine, our objective was clear: to install a MIDEA EVOX G3 2-ton central heat pump reliably, cleanly, and consistently with the house. The result is a discreet, well-secured installation adapted to the residential conditions of the North Shore.
MIDEA EVOX G3: a serious option for Greater Montreal homeowners
The MIDEA EVOX G3 range is increasingly in demand in the Quebec residential market. It positions itself as an attractive solution for homeowners who want good energy performance, modern operation, and a generally competitive cost compared to some more traditional brands.
Depending on the exact configuration, certain central heat pump models may be eligible for subsidy programs like Hydro-Québec's LogisVert, when the applicable criteria are met. Eligibility must always be validated according to the model number, indoor-outdoor combination, and requirements in force at the time of the project.
For our clients, this verification is essential. A subsidy can strongly influence the net cost of an installation, but it should never be presumed without technical validation.
What homeowners in Lorraine should remember
This installation clearly shows that a successful HVAC installation relies on a balance between performance, aesthetics, durability, and future service. The machine installed is important, but the way it is integrated into the home is just as important.
A 2-ton central heat pump can be an excellent solution for a residence in Lorraine when the capacity is well-chosen, the ducts are compatible, and the outdoor unit is installed in an appropriate location.
For homeowners in Montreal, Laval, Longueuil, the North Shore, and the South Shore, this project perfectly illustrates the importance of working with a team that understands local realities: snow, frost, limited clearances, existing homes, electrical constraints, subsidy requirements, and high expectations for finishes.
Our AirGreen approach for this type of project
For a MIDEA EVOX G3 central heat pump installation, our method relies on a series of precise steps:
- Analysis of actual heating and cooling needs.
- Verification of appropriate capacity.
- Evaluation of the outdoor location.
- Validation of electrical and mechanical constraints.
- Clean, stable installation in accordance with best practices.
- System commissioning.
- Explanation to the client of essential usage and maintenance points.
This rigor helps avoid unpleasant surprises and ensures a lasting result.
An installation ready for Quebec seasons
In Lorraine, winters can put HVAC equipment to the test. A central heat pump must be installed taking into account snow, defrosting, drainage, wind, and future access for maintenance. The wall-mounted installation visible in this project helps protect the unit and facilitate its operation in real conditions.
In summer, the same system provides comfortable central air conditioning, without excessive indoor noise or wall-mounted units in the main rooms. For many homeowners, this is precisely what makes the central heat pump so attractive: global comfort, discreet and well-integrated into the home.
Conclusion: a well-installed MIDEA EVOX G3, designed to last
This installation of a MIDEA EVOX G3 2-ton central heat pump in Lorraine demonstrates the importance of precise HVAC work adapted to the building. The choice of the unit, installation height, clearance around the unit, solidity of the brackets, and the overall quality of integration all contribute to the system's performance.
At AirGreen, we know that a good installation is not limited to the day of the work. It must remain reliable, accessible, and efficient for many years. That's why every detail counts, from the initial evaluation to the final commissioning.
How it goes, from the first call to the end
The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.
We look at the ducts, the current indoor module, the electrical panel and the planned spot for the outdoor unit.
The equipment combination, capacity and price, in writing. We check whether the combination qualifies for assistance programs.
Access protected, old unit disconnected and removed when it is being replaced.
Electric furnace or air handler, with its coil, connected to the supply and return ducts.
On a level base, raised above the snow, with free space all around.
Insulated, they enter through a sealed opening and run to the indoor coil.
Dedicated circuits, accessible disconnect, a thermostat that works with the heat pump and the backup heat.
Leak test, vacuum, start-up, airflow check and a test of both modes.
Filter, thermostat, backup heat in extreme cold: what to know before winter.
- The on-site estimateWe look at the ducts, the current indoor module, the electrical panel and the planned spot for the outdoor unit.
- The quoteThe equipment combination, capacity and price, in writing. We check whether the combination qualifies for assistance programs.
- Getting readyAccess protected, old unit disconnected and removed when it is being replaced.
- The indoor moduleElectric furnace or air handler, with its coil, connected to the supply and return ducts.
- The outdoor unitOn a level base, raised above the snow, with free space all around.
- The refrigerant linesInsulated, they enter through a sealed opening and run to the indoor coil.
- Electrical and thermostatDedicated circuits, accessible disconnect, a thermostat that works with the heat pump and the backup heat.
- Tests and start-upLeak test, vacuum, start-up, airflow check and a test of both modes.
- The walkthroughFilter, thermostat, backup heat in extreme cold: what to know before winter.
What the unit delivers when it is cold
The range as published on airgreen.ca: pick a size to see its capacity in deep cold.
| Size | Heating at −8 °C | Heating at −15 °C | Coldest certified point | COP at −15 °C | SEER | HSPF | Indicative LogisVert aid |
|---|---|---|---|---|---|---|---|
| Midea EVOX G3 · 1.5 tons | 14,700 | 18,600 | −30 °C: 11,800 | 2.12 | 19.0 | 10.1 | $1,764 |
| Midea EVOX G3 · 2 tons | 20,800 | 20,600 | −30 °C: 12,100 | 2.14 | 18.6 | 10.0 | $2,496 |
| Midea EVOX G3 · 2.5 tons | 24,000 | 33,200 | −30 °C: 17,900 | 1.97 | 17.2 | 10.8 | $2,880 |
| Midea EVOX G3 · 3 tons | 33,000 | 37,400 | −30 °C: 27,600 | 1.9 | 18.0 | 10.0 | $3,960 |
| Midea EVOX G3 · 4 tons | 39,500 | 48,000 | −30 °C: 27,200 | 2.0 | 17.5 | 9.5 | $4,740 |
| Midea EVOX G3 · 5 tons | 45,000 | 54,000 | −30 °C: 37,300 | 1.9 | 17.5 | 9.5 | $5,400 |
Data read live from the airgreen.ca page of each size (NEEP / AHRI certified performance). When the title names the installed size, it is highlighted; otherwise the whole range is shown. The aid shown is today’s, using Hydro-Québec’s rule ($120 per 1,000 BTU/h at −8 °C); amounts quoted in the article date from its publication. Only Hydro-Québec confirms the assistance granted.
And at your place?
Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.
Baseboards and electric furnaces turn 1 kWh of electricity into 1 kWh of heat. A heat pump delivers more: that is its COP. At Hydro-Québec’s rate D (11.142¢/kWh above 40 kWh a day, since 1 April 2026):
Hydro-Québec: a heat pump can be up to three times more efficient than baseboards for heating in the colder months.
Estimate per kWh of heat, at the chosen temperature, using the certified COP from the product page. Taxes, access charge and backup heat not included.
Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.
What to do, season by season
Three habits per season for this unit. They take a few minutes and prevent many calls.
- Check the indoor module's filter.
- Clear winter debris from the outdoor unit.
- Test cooling before the heat arrives.
- Check the filter more often in peak season.
- Keep registers and returns clear.
- Watch condensate drainage near the coil.
- Change or clean the filter.
- Test heating and backup heat before the cold.
- Book periodic maintenance.
- Clear snow around the outdoor unit.
- Store nothing in front of the indoor module.
- Note any unusual noise or smell and call us.
Which type of equipment for your project?
Pick what looks like your need.
Four mistakes we do not make
Flip each card to see what we do instead.
What people ask us about this kind of work
Can I keep my current ducts?
What happens in extreme cold?
Furnace, air handler, ducted: what is the difference?
Are there grants?
Do I need a permit?
How much can I save?
How is the LogisVert assistance calculated?
Will my current thermostat work?
Central or wall units: which one?
Does AirGreen hold the required licences?
Is the estimate free?
No question matches. Write to us: we answer.
Useful pages for what comes next
More jobs to see, near you
By town, by equipment or by region: browse more than 4,700 published projects.
Each dot: a town where AirGreen has published projects. The glowing dot: this job.
Tell us about your house. We come and see it for free.
The on-site estimate is free and the quote follows within 24 hours.
Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).
