Project

Installation of a Sharp BU Double Zone Heat Pump in Senneville

Discover how we installed the Sharp BU Double Zone Heat Pump in Senneville, delivering ultimate comfort with two zones, advanced features, and energy efficiency!

By AirGreen Climatisation & Chauffage Admin6 min read
Installation of a Sharp BU Double Zone Heat Pump in Senneville
Installation of a Sharp BU Double Zone Heat Pump in Senneville
Generic diagram: wall-mounted heat pump, indoor and outdoor units

In summer, the outdoor unit rejects the house's heat outside.

Generic illustration of this type of installation, not a survey of this job site. Tap a number.

  1. Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.

  2. The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.

  3. Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.

  4. A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.

  5. The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.

  6. On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.

  7. The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.

Where Comfort Meets Innovation: A Unique HVAC Project in Senneville

In the picturesque town of Senneville, where comfort meets tranquility, we at AirGreen recently completed a standout HVAC installation. This wasn’t just another heat pump setup—it was the installation of a Sharp BU Double Zone Heat Pump, an ideal solution for precise comfort control and year-round energy efficiency. Combining top-notch technology, a sleek design, and impressive specifications, this system delivers unmatched performance for modern households. Let us take you through the details of this project and the machine itself.

The Project: Perfect Comfort in Two Zones

The homeowner in Senneville sought an energy-efficient solution for both cooling and heating their space. After an in-depth consultation, we recommended the Sharp BU Double Zone Heat Pump—a 24,000 BTU system that efficiently powers two separate indoor zones:

  • Zone 1: A 9,000 BTU indoor unit perfectly suited for the bedroom, ensuring quiet, peaceful comfort.
  • Zone 2: An 18,000 BTU indoor unit installed in the living area for optimal heating and cooling of the main gathering space.

This setup provides not only precise temperature control but also remarkable energy savings, thanks to its 24.0 SEER efficiency rating and Energy Star® certification.

The Star of the Show: The Sharp BU Double Zone Heat Pump

Key Specifications at a Glance

  • Cooling Capacity: 24,000 BTU
  • Heating Capacity: Effective down to -27°C—perfect for harsh Québec winters
  • Noise Level: Only 50.0 dB(A) for the exterior unit, ensuring whisper-quiet operation
  • Gas Refrigerant: R-32, an eco-friendly choice for reducing environmental impact
  • Voltage: 220V for reliable, powerful performance
  • Warranty: 10 years for the compressor, parts, and labor
  • WiFi-Enabled: Remote temperature control for seamless, modern living

With these advanced features, the Sharp BU ensures both comfort and savings throughout every season.

Why R-32 Refrigerant Matters

The use of R-32 refrigerant is a significant advantage of this system. Compared to traditional refrigerants, R-32 has a lower Global Warming Potential (GWP), meaning it’s not only highly efficient but also environmentally responsible. This aligns with AirGreen’s commitment to offering sustainable solutions that reduce both energy bills and ecological footprints.


A Picture-Perfect Installation

When it came to the installation itself, precision was paramount. The outdoor unit (33.47 x 13 x 27.94 inches) was strategically placed to minimize visual impact and maintain airflow efficiency, while the two indoor units seamlessly blended into their respective spaces.

The 9,000 BTU unit was mounted above a doorway in the bedroom. This spot was chosen carefully to distribute cool or warm air evenly across the room without creating drafts. In the living room, the larger 18,000 BTU unit was installed to maximize comfort for the entire space.


A Grant-Worthy System: $3,000 LogisVert Eligibility

The Sharp BU Double Zone Heat Pump is not just a high-performance system; it’s also an investment that pays off. This model is eligible for Hydro-Québec's LogisVert grant of up to $3,000, helping homeowners significantly reduce installation costs.

Additionally, this system ranked first in our Guide des Thermopompes Murales 2025, a testament to its superior efficiency, durability, and innovative features.


Why the Sharp BU Double Zone is the Ideal Choice

1. Flexibility for Multi-Zone Comfort

With its double-zone capability, the Sharp BU is designed for homeowners who want tailored comfort in different areas of the home. Whether you need a cooler bedroom for better sleep or a warm and cozy living area for family gatherings, this system delivers.

2. Ultra-Quiet Operation

No one likes a noisy HVAC system. The Sharp BU operates at a near-silent level, ensuring a peaceful home environment. The exterior unit registers at just 50.0 dB(A), quieter than a standard conversation.

3. Winter-Ready Heating

The heating performance down to -27°C makes this heat pump a perfect solution for Québec winters. Even in frigid temperatures, the Sharp BU remains reliable and efficient.

4. WiFi Integration for Modern Living

Control your home’s climate from anywhere with the built-in WiFi feature. Whether you're adjusting temperatures from the comfort of your couch or remotely managing zones through your smartphone, the Sharp BU simplifies your life.

5. Self-Cleaning Function

The system’s self-cleaning function ensures continuous, clean air while minimizing maintenance. By reducing mold and allergens, it maintains a healthier indoor environment for you and your family.


Our Process: Seamless and Professional Installation

At AirGreen, every project begins with a thorough assessment of the home and the customer’s needs. For this installation in Senneville, we followed our trusted process:

  1. Site Assessment: We analyzed the home layout to determine the ideal placement for both indoor and outdoor units.
  2. Precision Installation: Our technicians installed the two indoor units with care, ensuring a clean and secure setup. The outdoor unit was positioned to optimize airflow and minimize noise.
  3. Testing and Calibration: After the installation, we tested the system for efficiency, air distribution, and temperature accuracy in both zones.
  4. Customer Walkthrough: We provided the homeowner with a full overview of the system’s operation, including how to use the WiFi features and maintain the units for long-term performance.

The AirGreen Advantage

With years of experience in HVAC installations across Montréal, Laval, Longueuil, North Shore, and South Shore, we pride ourselves on providing high-quality service and top-tier products. Here’s why customers choose us:

  • Expert Technicians: Our team is certified, knowledgeable, and committed to excellence.
  • Top-Quality Products: We work with industry-leading brands like Sharp to deliver reliable, high-performance systems.
  • Clear Communication: From consultation to installation, we keep you informed every step of the way.
  • Grant Assistance: We help customers navigate programs like LogisVert to maximize their savings.

Conclusion: Smart Comfort for Senneville Homeowners

The installation of the Sharp BU Double Zone Heat Pump in this Senneville home showcases AirGreen’s commitment to energy-efficient solutions and exceptional craftsmanship. This system offers unparalleled comfort, advanced features, and significant cost savings—making it the perfect choice for homes in Montréal, Laval, Longueuil, and beyond.

Whether you’re upgrading your heating system for winter or improving your cooling efficiency for summer, the Sharp BU delivers results you can trust.

In figures
The steps

How it goes, from the first call to the end

The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.

Step 1 of 9The on-site estimate

We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.

  1. The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
  2. The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
  3. Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
  4. The wall openingA single opening, with the slope the drain needs to flow outside.
  5. The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
  6. Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
  7. The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
  8. Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
  9. The walkthroughRemote, modes, filters: we show you the essentials before we leave.
The unit

What the unit delivers when it is cold

The range as published on airgreen.ca: pick a size to see its capacity in deep cold.

The range, size by size
SizeHeating at −8 °CHeating at −15 °CColdest certified pointCOP at −15 °CSEERHSPFIndicative LogisVert aid
Sharp BU 24 0002 Zones (Dual Zone)25,00021,200−27 °C: 14,6002.324.011.5$3,000
Sharp BU 24 0003 Zones (Triple Zone)25,00021,200−27 °C: 14,6002.324.011.5$3,000
Most EfficientENERGY STAR

Among the year’s most efficient according to ENERGY STAR, on top of its cold-climate certification.

8,800BTU/h at low speed

Minimum certified capacity (NEEP): it slows down instead of stopping when a single room calls.

−27 °CColdest certified point

NEEP still lists 14,600 BTU/h at a COP of 1.84 at −17 °F.

675R-32 GWP

Global warming potential of R-32, versus 2,088 for R-410A (ENERGY STAR).

Data read live from the airgreen.ca page of each size (NEEP / AHRI certified performance). When the title names the installed size, it is highlighted; otherwise the whole range is shown. The aid shown is today’s, using Hydro-Québec’s rule ($120 per 1,000 BTU/h at −8 °C); amounts quoted in the article date from its publication. Only Hydro-Québec confirms the assistance granted.

Your numbers

And at your place?

Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.

Before / afterThe cost of the same heat

Baseboards and electric furnaces turn 1 kWh of electricity into 1 kWh of heat. A heat pump delivers more: that is its COP. At Hydro-Québec’s rate D (11.142¢/kWh above 40 kWh a day, since 1 April 2026):

Before · baseboards11.142¢/kWh
After · heat pump–

Hydro-Québec: a heat pump can be up to three times more efficient than baseboards for heating in the colder months.

Estimate per kWh of heat, at the chosen temperature, using the certified COP from the product page. Taxes, access charge and backup heat not included.

Size checkYour baseboards, in BTU/h
–BTU/h of installed electric heat

    Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.

    Through the seasons

    What to do, season by season

    Three habits per season for this unit. They take a few minutes and prevent many calls.

    • Clean the indoor unit's filters.
    • Clear leaves and debris left on the outdoor unit by winter.
    • Test cooling before the first hot days.
    And at your place?

    Which type of equipment for your project?

    Pick what looks like your need.

    Mistakes avoided

    Four mistakes we do not make

    Flip each card to see what we do instead.

    Frequently asked questions

    What people ask us about this kind of work

    12 questions
    Does a wall-mounted heat pump heat in winter?
    Yes, it heats and cools. Its capacity drops in very cold weather; the operating range depends on the model and is listed on its spec sheet.
    Wall-mounted or multi-zone: how do I choose?
    One wall head and one condenser outside: the direct solution for a room or an open area. For two to five rooms, a multi-zone puts one head in each room on a single condenser.
    Where does the outdoor unit go?
    Where it stays above the snow, clear and accessible, away from walkways. We decide it with you during the estimate.
    Are there grants?
    Depending on the model and your situation, assistance programs may apply, including Hydro-Québec's LogisVert. AirGreen checks the model number before quoting an amount. See the grants.
    Do I need a permit?
    Rules vary from city to city: location, distances, noise. See permits and by-laws, and we check for your address.
    How cold can it heat?
    It depends on the model. According to Hydro-Québec, newer models work down to a temperature between −15 °C and −25 °C, and some cold-climate models are certified lower. The minimum temperature is on each unit's spec sheet.
    How much can I save?
    Hydro-Québec says a heat pump can be up to three times more efficient than baseboards for heating in the colder months. The result depends on the house, the climate and how it is used.
    How is the LogisVert assistance calculated?
    For ENERGY STAR cold-climate certified heat pumps, Hydro-Québec lists assistance of $120 per 1,000 BTU/h of heating capacity at −8 °C. AirGreen checks the exact model before quoting an amount; only Hydro-Québec confirms the assistance granted. See the grants.
    Is it noisy?
    The sound level depends on the model and is listed in decibels on each unit's spec sheet. Location matters too: when possible, we avoid putting the outdoor unit under a bedroom window.
    The outdoor unit is covered in ice: is that normal?
    Some frost is: the unit runs defrost cycles. Never hit the ice. If the unit stays iced up or stops heating, call us.
    Does AirGreen hold the required licences?
    Yes. AirGreen holds RBQ licence 5645-9605-01, subclasses 15.8 Ventilation, 15.10 Refrigeration and 16 Electricity.
    Is the estimate free?
    Yes. The on-site estimate is free and the quote follows within 24 hours. Book my free estimate.
    Going further

    Useful pages for what comes next

    Could this job help a neighbour?

    Share
    Similar projects

    More jobs to see, near you

    By town, by equipment or by region: browse more than 4,700 published projects.

    Each dot: a town where AirGreen has published projects. The glowing dot: this job.

    All our projects

    Your project

    Tell us about your house. We come and see it for free.

    The on-site estimate is free and the quote follows within 24 hours.

    • RBQ licence5645-9605-01 · 15.8, 15.10, 16
    • EstimateOn site, free
    • QuoteWithin 24 hours

    Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).

    Leave a comment