Installation of a Sharp ZU1 wall-mounted heat pump in Rosemont–La Petite-Patrie
AirGreen installed a Sharp Eco Inverter wall-mounted heat pump (type ZU1) in Rosemont–La Petite-Patrie, with wall bracket, anti-vibration and optimized clearances under soffit for reliable comfort summer and winter in Montreal.

In summer, the outdoor unit rejects the house's heat outside.
Generic illustration of this type of installation, not a survey of this job site. Tap a number.
Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.
The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.
Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.
A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.
The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.
On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.
The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.
In Rosemont–La Petite-Patrie, one often encounters buildings typical of Montreal: exposed masonry, balconies and soffits, sometimes limited utility spaces, and a very clear expectation from homeowners: year-round comfort without compromising on aesthetics or noise. This is precisely the context for this AirGreen installation, which features a Sharp Eco Inverter wall-mounted heat pump, designed to meet the temperature variations and performance requirements of the Quebec climate.
The photo shows the Sharp outdoor unit installed on a sturdy wall bracket, beneath a perforated ceiling structure (soffit type), with careful cable and connection management. This type of installation requires a rigorous approach: ensuring sufficient airflow, minimizing vibrations, and maintaining safe access for maintenance… all while respecting the building's physical constraints.
Why a Sharp wall-mounted heat pump in Rosemont?
Rosemont is an area where the needs are often very “concrete”:
-
Effective cooling in summer , especially during humid periods when homes quickly become uncomfortable.
-
Reliable heating in autumn and spring , and good efficiency in winter to reduce reliance on supplementary heating.
-
Silence and discretion , because the balconies, backyards and alleyways are close to the neighbors.
-
Clean installation , without altering the facade or cluttering outdoor spaces.
The Sharp ZU1 wall-mounted heat pump (a model consistent with this Sharp “Eco Inverter” configuration) meets these priorities very well, thanks in particular to its inverter modulation, its operational stability and its comfort-oriented approach.
The system installed: Sharp “Eco Inverter” (A2L refrigerant)
The visible outdoor unit clearly displays the Sharp logo and the Eco Inverter designation. It also features an A2L pictogram, typical of new generation refrigerants (low flammability category), frequently associated with modern systems aiming for a better balance between performance and environmental impact.
In practical terms, for the owner, what matters on a daily basis is:
-
a stable temperature (fewer fluctuations, fewer "cold flashes"/"heat flashes"),
-
controlled energy consumption thanks to the inverter compressor which adapts its power,
-
improved comfort even when the weather changes rapidly (very frequent in Montreal).
The installation details that can be seen in the photo
Even a "simple" wall-mounted heat pump installation can become technically complex when dealing with an existing structure, involving soffit clearances, required clearances, and access planning. Here are the key elements to consider:
1) Sturdy wall mount and leveling
The outdoor unit is mounted on an aluminum/steel wall bracket , designed to support the load while minimizing vibration transmission to the wall. Proper leveling is essential: a compressor must operate under optimal mechanical conditions, and an uneven unit can generate more noise and wear.
2) Anti-vibration pads/isolators
Blue elements are visible at the support point, typical of vibration dampers or isolators . In a dense neighborhood like Rosemont, this is a detail that makes a real difference: less vibration in the structure, therefore less resonance inside and less noise pollution.
3) Installation under the soffit: air vent management
The soffit above imposes a constraint: the unit must be able to draw in and expel air without recirculation. Recirculation (where the expelled cold air returns to the heat exchanger) can reduce heating efficiency and promote frost buildup. AirGreen therefore pays particular attention to clearances (lateral, rear, front, and top) and orientation.
4) Routing of refrigeration lines and cable
On the right, you can see a clean routing of the pipes/cables, grouped and secured, with mechanical protection. In outdoor environments, this is essential for:
-
reduce the risk of wear and tear (friction, UV rays, impacts),
-
improve the aesthetics,
-
facilitate maintenance (the installation is easier to “read”).
5) Future access for maintenance
The location was chosen to maintain reasonable access . A heat pump performs well over the long term if it is properly maintained: cleaning, pressure checks, connection inspections, and general checks. Installing it too close together can complicate maintenance and increase future costs—a mistake we always avoid.
Specific challenges in Montreal during winter (and how to anticipate them)
In Rosemont, the challenge is not just the August heat: it is above all the combination of cold + humidity + defrost cycles .
Defrosting: normal, but should be monitored.
In heating mode, the outdoor unit can frost up. The system then switches to defrost mode to remove the frost. Our role is to ensure that the installation allows for:
-
good drainage ,
-
a clear area beneath the unit,
-
air circulation that avoids cold recirculation.
Noise reduction in heating mode
The heating mode puts more strain on the outdoor unit. Hence the importance of:
-
anti-vibration isolators ,
-
from a rigid support,
-
of a proper attachment,
-
and a positioning that avoids acoustically "loading" a cavity (for example, too tightly wedged under a structure).
Why this installation is “typical AirGreen”
At AirGreen, we aim for an installation that remains efficient in real life : not just on the day of commissioning, but for years, in the real conditions of Montreal.
What we systematically prioritize
-
Performance : clearances, leveling, location selection.
-
Durability : support, protection of connections, assembly quality.
-
Acoustic comfort : anti-vibration, control of contact points.
-
Aesthetics : clean installation, controlled lines, discreet integration.
-
Service : access and maintenance logic integrated from the moment of installation.
What to expect after installation (comfort and habits)
A properly installed Sharp wall-mounted heat pump provides immediate savings, but good habits improve the experience even further:
-
Let the heat pump modulate (avoid constantly raising/lowering the setpoint).
-
Keep the internal filters clean (simple, but very worthwhile).
-
Plan for periodic maintenance and deep cleaning , especially in urban environments (dust, particles, pollen).
Conclusion: a well-integrated Sharp, designed for Rosemont
This installation in Rosemont–La Petite-Patrie perfectly illustrates what we are looking for: a Sharp Eco Inverter heat pump ( ZU1 coherent configuration), placed on a robust support, with real attention to vibrations, maintenance access and clearances — in short, an installation designed for everyday comfort, in the heart of the Montreal context.
How it goes, from the first call to the end
The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.
We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
Model, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
Floors and furniture protected, wall plate position marked level, wall opening located.
A single opening, with the slope the drain needs to flow outside.
Set on a stand raised above the snow, with the clearances the manufacturer requires.
Connected, insulated and protected. The opening is then sealed against water, cold air and insects.
A dedicated circuit and an accessible disconnect near the outdoor unit.
Leak test, vacuum, then start-up and a check of heating and cooling.
Remote, modes, filters: we show you the essentials before we leave.
- The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
- The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
- Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
- The wall openingA single opening, with the slope the drain needs to flow outside.
- The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
- Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
- The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
- Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
- The walkthroughRemote, modes, filters: we show you the essentials before we leave.
What the unit delivers when it is cold
The range as published on airgreen.ca: pick a size to see its capacity in deep cold.
| Size | Heating at −8 °C | Heating at −15 °C | Coldest certified point | COP at −15 °C | SEER | HSPF | Indicative LogisVert aid |
|---|---|---|---|---|---|---|---|
| Sharp ZU1 12 000 | 14,500 | 12,000 | −27 °C: 7,200 | 2.11 | 22.0 | 11.0 | $1,740 |
| Sharp ZU1 15 000 | 18,100 | 15,300 | −27 °C: 10,100 | 2.1 | 24.0 | 11.0 | $2,172 |
| Sharp ZU1 18 000 | 22,000 | 18,000 | −27 °C: 11,500 | 2.2 | 24.0 | 11.0 | $2,640 |
| Sharp ZU1 24 000 | 22,400 | 19,000 | −27 °C: 12,300 | 2.2 | 22.0 | 11.0 | $2,688 |
According to NEEP, it delivers 14,500 BTU/h at −8 °C (17 °F), more than at 8 °C (14,000 BTU/h). It heats as hard in moderate cold as in mild weather.
According to NEEP, its certified maximum capacity at −27 °C (−17 °F) is 7,200 BTU/h, 60% of its nominal 12,000 BTU size.
At 8 °C, its certified maximum capacity reaches 17,100 BTU/h, 42% more than its nominal 12,000 BTU size.
According to NEEP, it delivers 18,100 BTU/h at −8 °C (17 °F), more than at 8 °C (18,000 BTU/h). It heats as hard in moderate cold as in mild weather.
According to NEEP, its certified maximum capacity at −27 °C (−17 °F) is 10,100 BTU/h, 67% of its nominal 15,000 BTU size.
At 8 °C, its certified maximum capacity reaches 21,800 BTU/h, 45% more than its nominal 15,000 BTU size.
According to NEEP, it delivers 22,000 BTU/h at −8 °C (17 °F), more than at 8 °C (21,600 BTU/h). It heats as hard in moderate cold as in mild weather.
According to NEEP, its COP at −27 °C is 1.88: the highest of the ZU1 line, which ranges from 1.79 to 1.82 at that temperature.
According to NEEP, its certified maximum capacity at −27 °C (−17 °F) is 11,500 BTU/h, 64% of its nominal 18,000 BTU size.
At −27 °C, its certified minimum capacity is 3,200 BTU/h (5,500 at 8 °C). It slows down instead of cycling on and off.
According to NEEP, its certified heating capacity at −15 °C (5 °F) is 19,000 BTU/h, 79% of its nominal 24,000 BTU size. Its COP there is 2.20.
Data read live from the airgreen.ca page of each size (NEEP / AHRI certified performance). When the title names the installed size, it is highlighted; otherwise the whole range is shown. The aid shown is today’s, using Hydro-Québec’s rule ($120 per 1,000 BTU/h at −8 °C); amounts quoted in the article date from its publication. Only Hydro-Québec confirms the assistance granted.
And at your place?
Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.
Baseboards and electric furnaces turn 1 kWh of electricity into 1 kWh of heat. A heat pump delivers more: that is its COP. At Hydro-Québec’s rate D (11.142¢/kWh above 40 kWh a day, since 1 April 2026):
Hydro-Québec: a heat pump can be up to three times more efficient than baseboards for heating in the colder months.
Estimate per kWh of heat, at the chosen temperature, using the certified COP from the product page. Taxes, access charge and backup heat not included.
Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.
What to do, season by season
Three habits per season for this unit. They take a few minutes and prevent many calls.
- Clean the indoor unit's filters.
- Clear leaves and debris left on the outdoor unit by winter.
- Test cooling before the first hot days.
- Clean the filters more often when the unit runs a lot.
- Keep plants away from the outdoor unit.
- Check that no water drips from the indoor unit.
- Rake the leaves around the outdoor unit.
- Test heating before the first cold days.
- Book periodic maintenance before winter.
- Keep snow away from the stand and the front of the unit.
- Let the unit defrost: it is normal.
- Never hit the ice on the fins; call us if the unit stays iced up.
Which type of equipment for your project?
Pick what looks like your need.
Four mistakes we do not make
Flip each card to see what we do instead.
What people ask us about this kind of work
Does a wall-mounted heat pump heat in winter?
Wall-mounted or multi-zone: how do I choose?
Where does the outdoor unit go?
Are there grants?
Do I need a permit?
How cold can it heat?
How much can I save?
How is the LogisVert assistance calculated?
Is it noisy?
The outdoor unit is covered in ice: is that normal?
Does AirGreen hold the required licences?
Is the estimate free?
No question matches. Write to us: we answer.
Useful pages for what comes next
More jobs to see, near you
By town, by equipment or by region: browse more than 4,700 published projects.
Each dot: a town where AirGreen has published projects. The glowing dot: this job.
Tell us about your house. We come and see it for free.
The on-site estimate is free and the quote follows within 24 hours.
Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).
