Project

Installation of a FUJITSU Aquila R32 36,000 BTU Dual-Zone Heat Pump in Boucherville

Professional installation of a FUJITSU Aquila R32 36,000 BTU dual-zone heat pump in Boucherville. High-performance, energy-efficient HVAC solution on the South Shore.

By AirGreen Climatisation & Chauffage Admin5 min read
Installation of a FUJITSU Aquila R32 36,000 BTU Dual-Zone Heat Pump in Boucherville
Installation of a FUJITSU Aquila R32 36,000 BTU Dual-Zone Heat Pump in Boucherville
–chapters in this story
5 minreading time
–type of installation
2026year published
The tour

Take a tour of the installation

Each number is a point we check on site. Switch between summer and winter to watch air and heat move.

Generic diagram: wall-mounted heat pump, indoor and outdoor units

In summer, the outdoor unit rejects the house's heat outside.

Generic illustration of this type of installation, not a survey of this job site. Tap a number.

  1. Mounted level on a wall plate, high enough for the air to reach the whole room, with enough space around it to slide the filters out easily.

  2. The refrigerant lines, the communication cable and the drain go through the wall in a single opening, sealed against water, cold air and insects.

  3. Two insulated copper pipes connect the two units. Outside, a line cover can protect them from sun, knocks and weather.

  4. A shut-off switch near the outdoor unit isolates it safely for service. It must stay accessible at all times.

  5. The compressor and the fan. In heating mode it captures heat from the outdoor air, even in winter, and moves it inside.

  6. On the ground or on the wall, it keeps the unit above accumulated snow. The unit stays clear and defrost water can drain away.

  7. The fan needs to blow freely. Storage, a fence or a wall too close, and efficiency drops while noise goes up.

The job

Precise and Optimized HVAC Installation in a Residential Environment in Boucherville

At AirGreen, we regularly carry out complex HVAC installations on the South Shore, and this project in Boucherville perfectly illustrates our methodical and performance-oriented approach. This involves the installation of a FUJITSU Aquila R32 36,000 BTU dual-zone heat pump (model AOUH36KWAS4), a system designed to provide precise thermal comfort in two distinct zones of a residence.

Upon our arrival, several technical elements caught our attention: a restricted outdoor space, a brick facade requiring solid fixings, and careful management of the refrigerant lines. The image above clearly shows the outdoor unit installed on an elevated wall structure, a strategic decision to prevent snow accumulation and ensure better equipment durability.


A Dual-Zone Heat Pump Designed for Quebec's Climate

Technical Specifications of the Installed Model

The FUJITSU Aquila R32 36,000 BTU heat pump is an ideal solution for properties requiring independent management of two spaces:

  • Cooling Capacity: 36,000 BTU
  • Heating Capacity down to -15°C
  • R-32 Refrigerant (more ecological and efficient)
  • SEER2: 22.0 | HSPF2: 10.0 | EER2: 12.0
  • Outdoor Sound Level: 56 dB(A)
  • Dual-zone configuration (expandable up to 4 zones)

This model can power two distinct indoor units, often used for a living room and a bedroom or two separate floors. In this Boucherville project, we configured a balanced system to maximize heat and air conditioning distribution according to the client's needs.


Technical Challenges Encountered During Installation

Outdoor Space Management and Unit Support

The terrain had an irregular surface with accumulated leaves and moisture, which made ground installation risky in the long term. We therefore opted for:

  • A reinforced aluminum wall structure
  • Optimal elevation to avoid debris and snow
  • Secure fixing in the brick with professional anchoring

This choice not only guarantees stability but also better airflow around the unit, which improves overall performance.

Installation of Refrigerant Lines

The visible lines on the right side of the image show clean and structured work. We have:

  • Used high-quality insulated pipes
  • Ensured adequate slope for condensate drainage
  • Protected the conduits against bad weather with durable sleeves

A crucial point in any HVAC installation in Montreal, Laval, or Boucherville is to avoid energy losses caused by poor insulation or improper line routing.


Key Steps of the Installation Carried out by AirGreen

1. On-site Evaluation

First and foremost, we carried out a complete analysis:

  • Measurement of spaces to be air-conditioned
  • Verification of the electrical panel (220V required)
  • Analysis of load-bearing walls for fixing

2. Location Selection

The positioning of the outdoor unit is crucial. Here, we chose a side wall offering:

  • Good natural ventilation
  • Easy access for future HVAC maintenance
  • Optimal distance from indoor units

3. Installation and Commissioning

Our certified refrigeration technicians then:

  • Drilled openings with precision
  • Installed the wall mounts
  • Ran the refrigerant lines
  • Performed a vacuum test (micron test) to guarantee the absence of moisture and leaks
  • Started the system and validated performance

Why This Heat Pump Is an Excellent Choice in Boucherville

Energy Performance and Savings

Thanks to its high SEER2 and HSPF2 ratings, this FUJITSU heat pump significantly reduces electricity costs. It is particularly efficient in the climatic conditions of the South Shore, where winters can be harsh.

Personalized Comfort

With a dual-zone configuration, each space can be controlled independently:

  • Temperature adjusted according to room use
  • Reduction of energy waste
  • Optimal comfort for all occupants

Available Grant

This model is eligible for the LogisVert grant of approximately $1,180, making it an even more attractive investment for homeowners in Montreal, Laval, Longueuil, and the North Shore/South Shore.


Common Mistakes to Avoid During an HVAC Installation

We often see poorly executed installations in the field. Here's what to absolutely avoid:

  • Installing the outdoor unit directly on the ground without protection
  • Neglecting the vacuum test (risk of system contamination)
  • Using inadequate supports
  • Incorrectly sizing the zones

At AirGreen, every detail counts. A well-done installation can extend the system's lifespan by several years.


Customer Feedback

The Boucherville client was looking for a quiet, efficient, and discreet solution. After installation:

  • The sound level is practically imperceptible indoors
  • Temperature rise is fast and stable
  • The exterior aesthetic is clean and well-integrated into the facade

This type of feedback confirms the reliability of the model and the quality of our work.


System Maintenance and Durability

To maintain the performance of this dual-zone heat pump, we recommend:

  • Annual HVAC maintenance
  • Cleaning filters every 3 months
  • Inspection of ducts and compressor

At AirGreen, we offer tailored maintenance plans to ensure the longevity of your installation.


Why Choose AirGreen in Boucherville and on the South Shore

Our approach is distinguished by:

  • Recognized field expertise throughout the Montreal, Laval, Longueuil, and South Shore regions
  • Clean, durable, and optimized installations
  • Total transparency: payment only once the work is completed
  • Honest advice based on market realities

We don't just sell a machine. We offer a complete solution tailored to your reality.


Conclusion: A Controlled Installation for Lasting Comfort

This installation of a FUJITSU Aquila R32 36,000 BTU heat pump in Boucherville perfectly demonstrates the importance of professional HVAC work. Between choosing the right equipment, precise installation, and performance optimization, every step is essential.

At AirGreen, we continue to support our clients in Montreal, Laval, Longueuil, the North Shore, and the South Shore with reliable, high-performance solutions adapted to each situation.

The steps

The big day, step by step

The main steps of this kind of job at AirGreen. Every house has its quirks: the estimate brings them out.

Step 1 of 9The on-site estimate

We look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.

  1. The on-site estimateWe look at the room, the outside wall, the line route and where the outdoor unit will go. That is where the capacity gets chosen.
  2. The quoteModel, capacity and price, in writing. We also check whether the model qualifies for assistance programs.
  3. Getting readyFloors and furniture protected, wall plate position marked level, wall opening located.
  4. The wall openingA single opening, with the slope the drain needs to flow outside.
  5. The outdoor unitSet on a stand raised above the snow, with the clearances the manufacturer requires.
  6. Lines, cable and drainConnected, insulated and protected. The opening is then sealed against water, cold air and insects.
  7. The electrical workA dedicated circuit and an accessible disconnect near the outdoor unit.
  8. Tests and start-upLeak test, vacuum, then start-up and a check of heating and cooling.
  9. The walkthroughRemote, modes, filters: we show you the essentials before we leave.
Your numbers

What would it look like at your place?

Two quick checks with real numbers: what heat costs, and what your current heaters add up to in BTU/h.

Size checkYour baseboards, in BTU/h
–BTU/h of installed electric heat

    Conversion: 1 W = 3.412 BTU/h. An indication, not a load calculation: baseboards and furnaces are often stronger than the real need, and they can stay as backup. AirGreen confirms the capacity on site.

    Mistakes avoided

    Four mistakes we do not make

    Flip each card to see what we do instead.

    Going further

    Your own project, step by step

    Through the seasons

    What to do, season by season

    Three habits per season for this unit. They take a few minutes and prevent many calls.

    • Clean the indoor unit's filters.
    • Clear leaves and debris left on the outdoor unit by winter.
    • Test cooling before the first hot days.
    At your place

    Is your home ready?

    Check what applies at your place. A "no" is not a refusal: it is what we sort out during the estimate.

    0 / 6 checked
    True or false

    Four statements: true or false?

    It all comes down to details you have just seen.

    1. In heating mode, the outdoor unit can produce water.

    2. You pick the capacity with a simple square-footage rule.

    3. A multi-zone connects several indoor heads to a single condenser.

    4. The disconnect can sit behind the patio furniture.

    Frequently asked questions

    What people ask us about this kind of work

    12 questions
    Does a wall-mounted heat pump heat in winter?
    Yes, it heats and cools. Its capacity drops in very cold weather; the operating range depends on the model and is listed on its spec sheet.
    Wall-mounted or multi-zone: how do I choose?
    One wall head and one condenser outside: the direct solution for a room or an open area. For two to five rooms, a multi-zone puts one head in each room on a single condenser.
    Where does the outdoor unit go?
    Where it stays above the snow, clear and accessible, away from walkways. We decide it with you during the estimate.
    Are there grants?
    Depending on the model and your situation, assistance programs may apply, including Hydro-Québec's LogisVert. AirGreen checks the model number before quoting an amount. See the grants.
    Do I need a permit?
    Rules vary from city to city: location, distances, noise. See permits and by-laws, and we check for your address.
    How cold can it heat?
    It depends on the model. According to Hydro-Québec, newer models work down to a temperature between −15 °C and −25 °C, and some cold-climate models are certified lower. The minimum temperature is on each unit's spec sheet.
    How much can I save?
    Hydro-Québec says a heat pump can be up to three times more efficient than baseboards for heating in the colder months. The result depends on the house, the climate and how it is used.
    How is the LogisVert assistance calculated?
    For ENERGY STAR cold-climate certified heat pumps, Hydro-Québec lists assistance of $120 per 1,000 BTU/h of heating capacity at −8 °C. AirGreen checks the exact model before quoting an amount; only Hydro-Québec confirms the assistance granted. See the grants.
    Is it noisy?
    The sound level depends on the model and is listed in decibels on each unit's spec sheet. Location matters too: when possible, we avoid putting the outdoor unit under a bedroom window.
    The outdoor unit is covered in ice: is that normal?
    Some frost is: the unit runs defrost cycles. Never hit the ice. If the unit stays iced up or stops heating, call us.
    Does AirGreen hold the required licences?
    Yes. AirGreen holds RBQ licence 5645-9605-01, subclasses 15.8 Ventilation, 15.10 Refrigeration and 16 Electricity.
    Is the estimate free?
    Yes. The on-site estimate is free and the quote follows within 24 hours. Book my free estimate.

    Could this job help a neighbour?

    Share
    Similar projects

    More jobs to see, near you

    By town, by equipment or by region: browse more than 4,700 published projects.

    Each dot: a town where AirGreen has published projects. The glowing dot: this job.

    All our projects

    Your project

    Every house has its constraints. We see them before we install.

    The on-site estimate is free and the quote follows within 24 hours.

    • RBQ licence5645-9605-01 · 15.8, 15.10, 16
    • EstimateOn site, free
    • QuoteWithin 24 hours

    Text and photo: a real AirGreen Climatisation & Chauffage job. The diagrams are generic illustrations of the type of installation, not a survey of this job site. Sources of the added figures: airgreen.ca product pages (NEEP / AHRI performance), Hydro-Québec (Heat pumps page, LogisVert, read on 13 October 2026), Régie de l’énergie (rate D as of 1 April 2026).

    Leave a comment