BRADFORD WHITE RE2H80T10-1NCTT Heat Pump Water Heater (80 gallons) | Montreal, Laval, Longueuil, South Shore & North Shore

A large hot water reserve for very busy homes, heated mostly by a heat pump

Two full bathrooms, teenagers showering one after another, a large bath in the evening and loads of laundry almost every day: in this kind of home, an ordinary electric tank quickly runs out of reserve. The Bradford White RE2H80T10-1NCTT heat pump water heater meets that reality with a tank of 80 US gallons (67 imperial gallons, 303 L) and an integrated heat pump that produces most of the heat from the room air. It is the largest size in the Bradford White heat pump line that we offer, and AirGreen installs it in Montreal, Laval, Longueuil, on the South Shore and on the North Shore.

It suits a tank replacement in a large family home as well as new construction or a major renovation, where a mechanical room suited to a unit of this size can be planned from the start.

Which homes this size is designed for

The RE2H80T10-1NCTT targets households whose hot water use is high and concentrated in time: a family of five, for example, or an intergenerational home where two kitchens and several bathrooms draw on the same tank. It also appeals to homeowners who have installed a large tub or a multi-jet shower and run short of hot water in the evening. For a couple or a small family, a more compact size will often make more sense; we will tell you so frankly during the assessment.

Why tank size matters with a heat pump

The compressor of a heat pump water heater heats water slowly, but with very little electricity. According to Bradford White, this model recovers 6 US gallons per hour with the compressor alone, and 24 US gallons per hour when the compressor and an element work together. In practical terms, the larger the reserve, the less the unit needs its elements during peaks. With 80 US gallons of hot water in reserve, morning showers draw on water that is already hot, and the heat pump rebuilds the reserve during the day and overnight. This is what lets a large family enjoy a heat pump water heater without spending its time in electric mode.

Manufacturer specifications

• Capacity: 80 US gallons, 67 imperial gallons, 303 L.
• Uniform Energy Factor (UEF): 3.59, based on the AHRI directory.
• Recovery, compressor only: 6 US gal/h or 5 imperial gal/h at a 90 °F rise; 23 L/h at a 50 °C rise.
• Recovery, compressor and element: 24 US gal/h or 20 imperial gal/h; 91 L/h.
• Data measured in standard hybrid mode, at 19.7 °C (67.5 °F) ambient and 50% relative humidity.
• Power supply: single-phase 240 V/208 V, interlocked (non-simultaneous) elements.
• Screw-in backup elements: 4,000 W at 240 V; upper element of 3,000 W at 208 V.
• Water connections: 3/4 in. (19 mm) NPT with factory-installed dielectric fittings.
• Height: 70 13/16 in. (1,799 mm); diameter: 25 in. (635 mm).
• Weight: 259 lb (117 kg).

The principle in a few lines

On top of the tank, a fan draws in room air and passes it over an evaporator. The refrigerant picks up the heat from the air, the compressor raises its temperature and a condenser transfers it to the water. A large part of the energy thus comes from the room air rather than from the power grid. The discharged air is cooler and drier, and two electric elements take over when demand requires it.

Five modes at the pace of a large family

Heat pump mode, which uses only the compressor, works very well with a tank this size when the household routine is steady. Standard hybrid mode remains the most versatile choice: the heat pump does most of the work and an element steps in as needed. During busier weeks, such as the holidays or a visit from relatives, hybrid plus mode relies more on the elements to keep the reserve full. Electric mode serves as a backup, and vacation mode slows the unit down while you are away. At commissioning, we set the mode according to your family's actual schedule.

Planning the location of a tall, heavy unit

At 70 13/16 in. tall and 259 lb, this water heater needs a little more planning than a standard replacement. We measure the headroom under the joists, the width of the stairs and doorways, and the strength of the floor at the intended spot. The manufacturer's location requirements, whether the room's air volume, the clearances or the drainage of condensate water, are confirmed on site. In new construction, it is simple to reserve the space and the drain at the planning stage; in an existing house, an unfinished basement or the mechanical room is usually the best choice.

Because the discharged air is cooler and drier, the unit cools and dries the room in summer. In winter, in a heated room, part of the captured heat comes from the home's heating system, a point we take into account in our advice.

Materials and compliance

The tank receives Bradford White's Vitraglas with Microban lining and a protective anode rod. The low-restriction brass drain valve allows quick flushing, and the factory-installed dielectric fittings on the 3/4 in. connections limit galvanic corrosion. The manufacturer states that the model is ENERGY STAR certified, UL listed, C.E.C. listed and meets NAECA requirements.

Power supply

The RE2H80T10-1NCTT runs on a 240 V/208 V single-phase supply, with factory wiring that keeps the two elements from heating at the same time. In a large, well-equipped home, the electrical panel must keep the necessary capacity; we check the existing circuit and the panel load, then confirm the breaker size according to the nameplate. Electrical work is done under our RBQ licence 5645-9605-01 (ventilation, refrigeration and electrical).

Manufacturer's warranty

Bradford White covers this "10" suffix model with a 10-year limited warranty on the tank and 10 years on parts. The detailed terms come with your quote.

AirGreen installs your 80 US gallon heat pump water heater from start to finish

A family-owned heating and cooling company established in Montreal, AirGreen has been active for more than fifteen years. After a free in-home estimate, you receive a written quote that sets out every step. Installation of the RE2H80T10-1NCTT includes:

• checking the location, access, headroom and the drain for condensate water;
• draining and removing the old tank, or preparing the space in new construction;
• connecting the cold and hot water lines in 3/4 in. NPT;
• installing the relief valve and its discharge line;
• the electrical connection and a check of the panel;
• commissioning, and setting the temperature and mode to your family's schedule;
• maintenance advice: clear air intake, partial flushing, anode inspection.

Everywhere in Greater Montreal

We serve Montreal, Laval, Longueuil, Saint-Bruno, Varennes, Mirabel, Repentigny, Mascouche and the whole South Shore and North Shore. If you wish to spread out the investment, our financing option is presented with the quote.

Book your free estimate for the Bradford White RE2H80T10-1NCTT. A few photos of your current tank, the stairs and the intended location help us prepare an efficient visit.