Adjustable Galvanized Round 90° Elbow

In stock

The round elbow you set on site, from a slight bend to a full 90° turn.

AirGreen codeAG-VC-00203

Up to 90°angle set on site
4 to 16 in8 sizes
Galvanizedgalvanized steel
Adjustable elbowRound duct
Dimensions
Ask for a quote

514 316-2973 · sales@airgreen.ca

Quick facts

AirGreen codeAG-VC-00203
MaterialGalvanized steel
AngleAdjustable, up to 90°
Diameters4 to 12 in, 14 / 16 in
SoldEach

The adjustable galvanized round elbow changes the direction of a round duct at the angle you need, up to 90°. Its sections rotate on one another: you set it on site, at installation, instead of ordering a different elbow for each turn.

The elbow that adapts to the actual route

In a basement or attic, a duct often has to get around a beam, a pipe or a brace, and two runs are rarely perfectly aligned. The adjustable elbow takes up these offsets. It is also used for the full 90° turn that brings a branch to a floor register or to a wall hood.

Available sizes

The elbow is available in 4, 5, 6, 7, 8, 10 and 12 in, as well as a combined 14 in / 16 in size for main ducts. The latter is a single variant: specify the exact diameter when ordering. The size is the nominal diameter of the pipe to be connected.

Adjustment and sealing

  • Set the angle dry, by holding the elbow in place between the two runs.
  • Lock each swivel joint with a sheet metal screw so the angle no longer moves.
  • Seal the swivel joints and both connections with aluminum tape or duct sealant.
  • Avoid putting several elbows in a row: every turn slows the air.

On an exhaust duct, slope the run toward the outside after the last elbow so condensation does not flow back toward the unit.

Installed by AirGreen in Greater Montréal

We install ducts and elbows as part of our ventilation and forced-air work in Montréal, Laval, Longueuil, on the South Shore and on the North Shore. RBQ licence 5645-9605-01, subcategory 15.8 Ventilation. For availability or a quote, call us at 514 316-2973 or email sales@airgreen.ca with the diameter and quantity.

01 · What it is for

One elbow for every angle on the job

Its sections swivel on each other: you set the exact angle while installing, instead of hunting for the right elbow.

  • 90° turns along a wall, a joist or a ceiling
  • Getting around a beam, a plumbing pipe or blocking
  • Small offsets between two ducts that are not perfectly in line
  • Connecting a boot or a wall hood to the branch
Adjustable angleThe sections swivel to give any angle up to 90°.
Fewer partsOne model covers square turns and in-between angles.
Eight sizesFrom 4 to 12 in, plus a 14 / 16 in size for large ducts.
02 · Sizes

8 sizes, one page

Each size has its own AirGreen code. Tap a row to select it.

DimensionsAirGreen code
4 inAG-VC-00201
5 inAG-VC-00202
6 inAG-VC-00203
7 inAG-VC-00204
8 inAG-VC-00205
10 inAG-VC-00206
12 inAG-VC-00207
14 in / 16 inAG-VC-00208

Nominal duct diameter. For the 14 in / 16 in size, state the exact diameter when ordering.

03 · Specifications

Specifications

From the manufacturer’s documentation. A value the manufacturer does not publish is not listed.

TypeAdjustable round elbow
AngleAdjustable up to 90°
MaterialGalvanized steel
Diameters4, 5, 6, 7, 8, 10 and 12 in; 14 / 16 in
SoldEach
AirGreen codeAG-VC-00203
04 · Before installing

What to know before installing

  • Choose the elbow with the same nominal diameter as the pipe.
  • Set the angle before installing, then lock it with a sheet-metal screw on each swivel joint.
  • Seal the swivel joints with foil tape or mastic: they are leak points.
  • The 14 in / 16 in size is a single variant: state the diameter you need when ordering.
05 · Goes with

You may also need

Same category
Ventilation ducts
See all
06 · Questions

Frequently asked questions

How do I set the angle?

Turn the sections against each other until you reach the angle you want, then fasten them with a sheet-metal screw and seal the joints.

Can it be used as a 45° elbow?

Yes. That is the point of an adjustable elbow: it gives any angle up to 90°, 45° included.

Why seal a new elbow?

Swivel joints let air through. Foil tape or mastic on each joint keeps the air in the duct.

Can you install it?

Yes. We install ducts and fittings as part of our ventilation and forced-air jobs across Greater Montréal.

AirGreen · Montréal, Laval, Longueuil, South Shore, North Shore

Elbows fitted to your duct route

Tell us the size and the quantity: we confirm availability and send you a quote. Or let our technicians install it for you.

RBQ 5645-9605-01Ventilation, refrigeration and electrical
Free estimateon site, for any installation
Quote in 24 hby phone or email
Bouchervilleshowroom

Specifications from the manufacturer’s documentation, checked on October 7, 2026.