Fantech ERV FIT 80E-M-HC Air Exchanger | Montreal, Laval, Longueuil, South Shore and North Shore
Is it the right size for your home?
It delivers 78 cfm net, enough to ventilate 800 to 1,400 sq ft. Choose your home's living area.
It's the right size.
For a 900 to 1,500 sq ft home, about 63 cfm of air needs to be renewed continuously. This unit delivers 78 cfm net — enough for the house, with extra capacity to boost ventilation for the bathroom and kitchen.
Calculation: 0.35 air changes per hour over the living volume, with 9 ft ceilings. Our estimator sets the exact airflow room by room, following CSA F326.
What it does, in numbers
$40.99
Electricity per year
Less than a 60 W light bulb
Bulbs left on day and night. Same calculation for every line: wattage × 8,760 h × 11.142 ¢/kWh.
Meets the Québec Construction Code for Greater Montréal. The Code requires 54% at −25 °C below 6,000 degree-days (Montréal, Laval, Longueuil and both shores) and 60% above that. This unit is rated at 55% at 53 cfm.
Airflow and efficiency at 0 °C and −25 °C: HVI directory, Section III. Cost: 42 W over 8,760 h at Hydro-Québec's Rate D second tier (11.142 ¢/kWh).
What you should know about this one
Published, verifiable facts, not brochure claims.
-MMirrored version: dwelling-side ports on the left
On the FIT 80E, the dwelling's supply and return air connect on the right-hand side; on the FIT 80E-M-HC, they move to the left. One building can thus serve mirror-image floor plans, with the installation drawings simply read in reverse.
-HCHard-connect version shipped without a cord
The -HC (hard connect) suffix means the unit ships with no power cord and is wired directly to the circuit where code requires it. On the FIT 80E-M-HC, the supply wires enter the electrical box through a 3/8 in cable fastener and connect to the unit's leads and ground screw.
55%What it still recovers at −25 °C
The only efficiency figure that matters for a Québec winter, and the one the Code uses. An efficiency quoted without its temperature means nothing; this one is measured at a test airflow of 53 cfm.
ExhaustIt defrosts by pausing the fresh air for a few minutes
In cold weather, the supply fan stops for a few minutes while the exhaust keeps running, so warm indoor air thaws the core. During the cycle the house is briefly under negative pressure; if you have a fireplace or a naturally vented combustion appliance, mention it to our estimator.
ERVIt moves moisture too, not just heat
An ERV transfers some moisture between the two airstreams. Useful in a house that gets too dry in winter or takes on a lot of humidity in summer. The trade-off: it generally recovers less heat than a comparable HRV.
2005303Its HVI certification number
Listed in Section III of the Home Ventilating Institute's certified products directory. Anyone can check it.
−15 cfmWhat the ducts cost it
Between a nearly unrestricted test bench (0.2 in) and a real duct system (0.4 in), it drops from 93 to 78 cfm.
42 WMeasured at the airflow it actually runs at
Its 70% at 0 °C is certified at 42 cfm, the continuous airflow of a typical home. At that setting it draws 42 W, or about 368 kWh a year.
5 yearsThe core warranty
The core does the work and is the most expensive part to replace. Motors: 7 years. Parts: 5 years.
4 inWhat it needs on site
4 in ducts, side connection. It weighs 29 lb, and it needs enough clearance to slide the core out once a year.
Rénoclimat stopped funding HRVs and ERVs on October 1, 2026
Only files opened before that date, under the program's transition rules, remain eligible. This unit's HVI Section III certification (No. 2005303) remains the public proof of its performance: we balance it to the calculated airflow rather than running it at full speed.
What it needs on site
In a condo with no floor drain, or with little ceiling clearance, we usually look at a side-port model instead. Our estimator checks the location, the drain and the duct route before ordering.
Complete spec sheetData and cited sources
- Net airflow at 0.2 in. w.g.
- 93 cfm
- Net airflow at 0.4 in. w.g.
- 78 cfm
- SRE at 0 °C (42 cfm)
- 70%
- SRE at −25 °C (53 cfm)
- 55%
- ASE at 0 °C
- 75%
- Power draw
- 42 W
- Efficacy
- 1.0 cfm/W
- Type
- ERV
- Connection
- Side ports
- Duct collars
- 4 in
- Defrost cycle
- Exhaust only (supply fan off)
- Filters
- 2 washable electrostatic MERV 3 panel filters (9 1/2 × 8 1/2 in); optional MERV 8 (484397) and MERV 13 (484396)
- Dimensions (L × D × H)
- 20.63 × 18.19 × 10.06 in
- Weight
- 29 lb
- Power supply
- 120 V
- HVI certification (Section III)
- 2005303
- Warranty — core
- 5 years
- Warranty — motors
- 7 years
- Warranty — parts
- 5 years
- Spec sheet (French)
- Spec sheet (English)
Net airflow, efficiency at 0 °C and −25 °C, and power draw: Home Ventilating Institute certified products directory, Section III (HVID 2005303). Annual consumption calculated at 42 W running continuously for 8,760 h, at Hydro-Québec's Rate D second tier (11.142 ¢/kWh), in effect since April 1, 2026.
The next model down and up
Talk to an HVAC technician before you choose
We calculate the airflow room by room, check the location and the drain, and give you an installed price. Balancing is measured at commissioning, not estimated.
For baseboard-heated condos with a reversed plan and fixed wiring
Many Greater Montreal condos have no furnace: they are heated by electric baseboards, sometimes with a wall-mounted heat pump. The air exchanger there has its own duct system, and a motorized damper has no role to play. The Fantech FIT 80E-M-HC is designed for this context: dwelling connections on the left (-M) and a permanent electrical supply, with no cord (-HC).
This energy recovery ventilator (ERV) offers a net airflow of 78 cfm at 0.4 in. and 93 cfm at 0.2 in., in a 10.06 in. thick cabinet. The 80 format suits dwellings whose ventilation calculation stays below that airflow.
The fully dedicated installation
Fantech presents this method as the best one for new construction. Fresh air is distributed to the bedrooms and main rooms, and stale air is drawn from the bathroom, the kitchen or the laundry room, without going through a forced-air system. The manufacturer suggests it with electric baseboards, hydronic heating, radiant floors and wall-mounted heat pumps. Supply grilles go high on the wall or on the ceiling, with diffusers that spread the air without an unpleasant draft.
Two options, two reasons
The mirror version serves buildings where half of the units are built as the reverse of the other half: the connections arrive on the left side, and the duct plan stays simple. The version without a cord meets the codes and specifications that require a fixed connection. The wires pass through a 3/8 in. cable clamp and connect to the wires and the ground screw in the electrical box, with a clearance of 2 3/8 in. above it.
For the developer, both options come from the factory on the same unit: nothing to modify on site, no cord to remove, no connection to move.
Performance figures
- Sensible recovery efficiency: 70% at 0 °C (42 cfm), 75% adjusted.
- At −25 °C: 55% at 53 cfm, beyond the 54% threshold of section 9.32 of the Code for Greater Montreal.
- Total recovery in cooling mode: 50% at 35 °C.
- Power consumption: 42 W at 42 cfm (1.0 cfm/W), and 368 kWh per year according to the estimate in the spec sheet above.
- Operating current: 0.6 A.
Defrost starts at −10 °C and below: the supply fan stops, the exhaust switches to high speed, then the unit returns to its normal cycle.
Controls in a condo building
For a developer, the question is often who will adjust the unit. For the FIT 80 series, Fantech recommends the ECO-Feel Auto IAQ control: a VOC sensor, an automatic mode that adapts to the season, no buttons and no battery. The occupant has nothing to adjust. If you prefer to leave a choice, the EDF3 offers three modes (Econo, 20 minutes per hour, continuous). In the bathrooms, RTS2 or RTS5 timers switch the ERV to high speed; up to five can be connected to a single unit.
The cabinet is 22-gauge G90 galvanized steel, with a prepainted door and 3/4 in. high-density expanded polystyrene insulation. The factory-balanced fans run on sealed ball bearings that need no lubrication.
Dimensions, weight and maintenance
The cabinet measures 20.63 × 18.19 × 10.06 in. and weighs 29 lb with the core. It requires no drain. Its two washable MERV 3 filters (9 1/2 × 8 1/2 in.) can be replaced with MERV 8 (484397) or MERV 13 (484396) filters. Allow 8 1/2 in. in front of the door: that is the space needed to take out the 10 × 10 in. core.
Warranty
Fantech's limited warranty is 7 years on the motors and 5 years on the core and electrical components.
Installation by AirGreen in the Montreal area
We install ERVs in condos and townhouses in Montreal, Laval, Longueuil, the North Shore and the South Shore. Each project starts with a room-by-room calculation according to CSA F326. We then install the dedicated ducts, the exterior hoods and the unit, then balance supply and exhaust to the calculated airflow.
In the HVI directory, the FIT 80E-M-HC is certified in Section III (No. 2005303): anyone can check its airflows and efficiencies there. Rénoclimat stopped funding HRVs and ERVs on October 1, 2026, except for files already opened under the program's transition rules.
Free quote at 514 316-2973 or sales@airgreen.ca.
