BRADFORD WHITE M3ST80R5 Hot Water Storage Tank (80 gallons) | Montreal, Laval, Longueuil, South Shore & North Shore

In stock
SKU: M3ST80R5
303 L80 US gal of storage
5 yrstank warranty
Talk to an expert · 514 316-2973
5-year tank warranty, 1-year parts2 in NPT connections
01 · Why this model

What sets the Bradford White M3ST80R5 apart

192 lb

Shipping weight

Bradford White sheet C407 lists an approximate shipping weight of 192 lb for the M-3-ST80R5.

2 in NPT

Water connections

Water connections are 2 in NPT (front and top).

180 °F

Storage up to 82 °C

The tank is designed to store potable water up to 180 °F (82 °C) at 150 psi working pressure.

2 anodes

Tank protection

The Vitraglas with Microban lined tank is protected by two anode rods.

02 · How it works

A hot water reserve, not a water heater

Heating applianceboiler or water heaterhot waterreturnTo the fixturesStoragehot waterstays on top
  1. A boiler or a water heater heats the water.
  2. A pump circulates it to the tank, which keeps it hot.
  3. At peak times the reserve adds to production: more hot water available at once.
03 · Will it fit?

Check the height and the way in before our visit

It travels upright. Measure the ceiling at the spot and the narrowest door on the way.

in
in

Unit: 58.75 in tall (1492 mm), 24 in across (610 mm), about 192 lb shipping weight. The clearances the manufacturer requires are checked on site.

04 · Your current tank

How old is yours?

The year it was made is on the tank’s rating plate. Enter it.

Signs it is wearing out

  • Hot water runs out sooner than it used to.
  • The water comes out slightly reddish.
  • Rust shows at the bottom of the tank.
  • Moisture or drips around the unit.

Manufacturers announce a 10 to 15 year life. Many insurers require replacement after 10 or 12 years and may refuse a water damage claim past that age (CAA-Québec). Check your policy.

05 · Installation

What the spot needs, and who does what

A heat sourceA boiler or water heater sized for the demand, with its circulation pump.
2 in NPT waterCold inlet, hot outlet and an accessible shut-off valve.
T&P valveTemperature and pressure relief valve, with its discharge line.
Pan and detectorDrip pan under the tank and a leak detector: strongly recommended (CAA-Québec).

AirGreenFree visit and quote, coordination of the work.

HeatingBoiler connection by a hydronic heating contractor (RBQ 15.4).

PlumberWater connections and relief valve by a master pipe-mechanic (CMMTQ).

YouA photo of the rating plate, the spot and the stairs saves us a trip.

06 · Maintenance

A few habits that make it last

  1. Start-up daySetting the temperature, with you.
  2. Every yearPartial drain to flush sediment, and a test of the relief valve.
  3. Depending on your waterAnode inspection: it wears so the tank steel does not. In hard water it goes faster.
07 · Spec sheet

Every figure, with its source

Capacity and performance
Model
M3ST80R5
Capacity
80 US gal · 303 L
Dimensions and connections
Height
58.75 in · 1,492 mm
Diameter
24 in · 610 mm
Shipping weight (approx.)
192 lb · 87 kg
Water connections
2 in NPT (front and top)
Build and warranty
Inner lining
Vitraglas with Microban
Drain valve
Brass
Limited warranty, tank
5 years
Limited warranty, parts
1 year

Manufacturer data. Detailed sources at the bottom of the page.

08 · Same family

The size below and above

80 US gal58.75 in tallYou are here
119 US gal62.5 in tallSee the larger one
09 · Questions

What people ask us most

Is there a LogisVert grant for this water heater?

No. Hydro-Québec’s LogisVert guide (version 1.10, September 15, 2026) lists no water heater among its eligible measures. At quote time we check other programs that could apply to your address.

What is a storage tank for?

It does not heat water itself. It holds water heated by a boiler or a water heater, to meet the big peak demands of a business or a building.

Who does the installation?

AirGreen does the visit and the quote and coordinates the work. The water connections are done by a master pipe-mechanic (CMMTQ).

10 · AirGreen

We check the spot before we sell you anything

Free on-site estimate, written quote. Send a photo of your current tank and its plate, and we prepare the visit.

Book my free estimate
Sources checked November 2, 2026.
  1. Bradford White M-3 Storage Tank spec sheet C407-0526 CANADA · cdn.shopify.com
  2. Québec.ca, “Eau chaude”, updated November 5, 2025 (186 L/day, 7 °C water, 60 °C, volumes per use).
  3. Québec Construction Code, Chapter III Plumbing, art. 2.2.10.7 (RBQ).
  4. CAA-Québec, “Chauffe-eau: quelle capacité choisir”, updated June 29, 2026.
  5. Hydro-Québec, LogisVert residential participation guide, version 1.10, September 15, 2026.

Costs shown are indicative estimates before tax.

Add 80 US gallons of hot water in reserve without replacing your water heater

Sometimes an electric water heater works very well but no longer keeps up at peak times. A business has added a washing station, a duplex has been converted into a single-family home with two more bathrooms, a daycare fills several sinks at once at lunchtime. The Bradford White M3ST80R5 hot water storage tank answers that need: it keeps 80 US gallons (67 imperial gallons, or 303 L) of already heated water in reserve, ready to be used along with the water from the heater. AirGreen installs it in Montreal, Laval, Longueuil, on the South Shore and on the North Shore.

The role of a hot water storage tank

A storage tank does not heat water by itself. It has no element and no coil: it is an insulated tank that holds the water produced by another unit, such as an electric water heater or an electric boiler. Its benefit is simple. The water heater works continuously at its own pace and fills the reserve; when demand jumps suddenly, the stored water adds to the heater’s water and the temperature at the tap holds longer.

This approach often avoids replacing a unit still in good condition with a larger model. It also splits the hot water volume between two tanks, which makes it easier to get through a narrow staircase or into a small mechanical room.

Where the M3ST80R5 fits

With its 80 US gallon volume, this tank suits small buildings and neighbourhood businesses rather than large buildings. A few typical examples: a hair salon rinsing hair all day long, a daycare, a small restaurant or café whose dishwasher and sinks run together, a plex whose hot water is produced by a single unit, or a large home heated by an electric boiler whose hot water production lacks reserve.

In each case, we start from the real demand: number of fixtures, appliances running at the same time and length of the peaks. The tank is only recommended if it truly solves the situation; sometimes a better-sized water heater remains the best solution.

How it fits into an existing electric installation

The tank is connected to the water heater or electric boiler by a piping loop. A small circulating pump, controlled by a thermostat, moves water between the heating unit and the reserve to keep it at the right temperature. Cold water enters the system, passes through the water heater, then goes to the tank and to the taps depending on the layout chosen.

Because stored water can be kept hotter than the water delivered to the taps, we add a thermostatic mixing valve at the outlet when needed to limit the risk of scalding. The exact layout depends on your current unit; it is explained in the quote, along with the choice of pump and controls.

Manufacturer’s data

  • Capacity: 80 US gallons / 67 imperial gallons / 303 L
  • Working pressure: 150 psi (1,034 kPa)
  • Water connections: 2 in (51 mm) NPT
  • Inner lining: Vitraglas with Microban
  • Insulation: 2 in (51 mm) CFC-free foam on the sides and top of the tank
  • Protection: two anode rods
  • Drain valve: brass, low-restriction, designed to resist vandalism
  • Dimensions: height 58 3/4 in (1,492 mm), diameter 24 in (610 mm)
  • Weight: 192 lb (87 kg)
  • Standard: meets or exceeds ASHRAE 90.1b

A tank protected by two anodes

The inside of the M3ST80R5 is lined with Vitraglas with Microban, Bradford White’s lining for its steel tanks. The manufacturer adds two anode rods. An anode wears away on purpose in place of the steel: with two rods, protection is better spread over the height of the tank. In a tank where the water is renewed every day, this detail weighs heavily on service life, especially when the water is hard or treated by a softener.

Insulation and drain valve

2 in of CFC-free foam covers the sides and top of the tank, and Bradford White states that its storage tanks meet or exceed the ASHRAE 90.1b standard. For a tank that holds hot water at all times, good insulation is part of the basic equipment.

The brass drain valve is low-restriction: yearly draining removes sediment better than with a small plastic valve. Its vandal-resistant design is appreciated in businesses and common areas where several people have access to the mechanical room.

Working pressure and safety

The working pressure is 150 psi (1,034 kPa). Like any hot water tank, the M3ST80R5 must be protected by a suitable relief valve, with a discharge pipe directed to a drain. If the building’s water entrance has a check valve, we also plan a thermal expansion tank. For buildings where ASME construction is required, Bradford White offers it as an option in this series; we check this requirement with you before ordering.

Manufacturer’s warranty

Bradford White provides a 5-year limited tank warranty and a 1-year limited parts warranty.

Dimensions and choice of location

At 58 3/4 in high and 24 in in diameter, the M3ST80R5 fits beside the existing water heater in most mechanical rooms. It weighs 192 lb empty, but much more once filled: it must sit on a concrete floor or a solid, level base, ideally near a floor drain. The shorter the distance to the water heater, the simpler the circulation loop and the less heat it loses.

Installation of the Bradford White M3ST80R5 tank by AirGreen

AirGreen is a family business established in Montreal and active in heating, ventilation and air conditioning for more than fifteen years. Our RBQ licence 5645-9605-01 covers ventilation, refrigeration and electrical work. For adding a storage tank, our work includes:

  • assessment of the hot water demand and of the existing heating unit;
  • choice of location, check of the floor and access to the drain;
  • if needed, removal of an old tank that is out of service;
  • 2 in water connections, the circulation loop and isolation valves;
  • installation of the relief valve, the discharge pipe and, if required, the expansion tank and mixing valve;
  • the electrical connection of the circulating pump and its control;
  • commissioning, temperature settings and maintenance advice, including yearly draining and anode inspection.

We serve businesses and homes in Montreal, Laval, Longueuil, Brossard, Saint-Hubert, Boucherville, Blainville, Repentigny and the entire South Shore and North Shore. Free on-site estimate, written quote and financing available.

Request your free quote for the Bradford White M3ST80R5 tank. Send us a photo of your current water heater and its rating plate: we will tell you whether a storage tank solves your hot water shortage.